Panasonic WV-S2231L Network Camera Installation Guide

Panasonic WV-S2231L Network Camera

Product Information:

The product is a network camera with the following model numbers:

• WV-S2231L
• WV-S2211L
• WV-S2131L
• WV-S2131LRF
• WV-S2131LEG
• WV-S2131
• WV-S2130
• WV-S2111L
• WV-S2110

The product should be installed and operated following the provided instructions. The model number is abbreviated in some descriptions in the manual. The manual also provides contact information for i-PRO Americas Inc., i-PRO Co., Ltd. in Fukuoka,Japan, and i-PRO EMEA B.V. UK Branch.

Product Usage Instructions

Before attempting to connect or operate the product, please read the instructions carefully and save the manual for future reference.
To understand the basic description of the product, refer to the Important Information on the provided CD-ROM.
To learn how to perform settings and operate the camera, refer to the Operating Instructions on the provided CD-ROM.
The model number and serial number of the product can be found on its surface. It is recommended to note down these numbers for identification purposes in case of theft.

For safety reasons, follow these important instructions:

1. Read and keep these instructions.
2. Heed all warnings.
3. Follow all instructions.
4. Avoid using the product near water.
5. Clean the product only with a dry cloth.
6. Ensure ventilation openings are not blocked during installation.
7. Avoid installing the product near heat sources.
8. Use only attachments/accessories specified by the manufacturer.
9. Use the recommended cart, stand, tripod, bracket, or table when using the product.
10. Unplug the product during lightning storms or when unused for long periods of time.
11. Refer servicing to qualified personnel if the product is damaged or not operating normally.

Network Camera

Model No. WV-S2231L / WV-S2211L
WV-S2131L / WV-S2131LRF
WV-S2131LEG / WV-S2131
WV-S2130 / WV-S2111L / WV-S2110

WV-S2131L

• Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
• For information about the basic description of this product, refer to the Important Information on the provided CD-ROM. For information about how to perform the settings and how to operate the camera, refer to the Operating Instructions on the provided CD-ROM.
• The model number is abbreviated in some descriptions in this manual.

For U.S. and Canada:
i-PRO Americas Inc.
https://www.i-pro.com/

For Europe and other countries:
i-PRO Co., Ltd. Fukuoka, Japan
https://www.i-pro.com/
i-PRO EMEA B.V. UK Branch
1010 Cambourne Business Park,
Cambridgeshire CB23 6DP
Authorised Representative in EU:
i-PRO EMEA B.V.
Laarderhoogtweg 25, 1101 EB
Amsterdam, Netherlands

Important safety instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damagedin any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Troubleshooting

Before requesting service, refer to the Important Information (included in the CD-ROM) and “Troubleshooting” in the Operating Instructions (included in the CD-ROM) and confirm the trouble.

Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU Lesser General Public License), etc.
• Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.
• Refer to the “readme.txt” file on the provided CD-ROM for further information about open source software licenses and the source code.
• Please note that we shall not respond to any inquiries regarding the contents of the source code.

WARNING:

• To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance with the installation instructions.
• To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.
• The apparatus should not be exposed to dripping or splashing.
• All work related to the installation of this product should be made by qualified service personnel or system installers.
• The installation shall be carried out in accordance with all applicable installation rules.
• The connections should comply with local electrical code.
• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunlight, fire or the like.

CAUTION:

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• The network camera is only intended for a connection to an ethernet or PoE network without routing to the outside plant.

Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

The model number and serial number of this product may be found on the surface of the unit.
You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: To assure continued compliance, (example – use only shielded interface cables when connecting to computer or peripheral devices).
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Direct current symbol

Hot surface symbol

Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

About notations

The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.

• S2131L:The functions with this notation are available when using the model WV-S2231L / WV-S2131L/ WV-S2131LRF / WV-S2131LEG / WV-S2131.
• S2130:The functions with this notation are available when using the model WV-S2130 / WV-S2110.
• S2111L:The functions with this notation are available when using the model WV-S2211L / WV-S2111L.

About the user manuals

Product documentation is composed of the following documents.

• Installation Guide (this document): Explains installation, mounting, cable connections, and adjusting the field of view. This manual uses the WV-S2111L as an example in the explanations.
• Important Information (included in the CD-ROM): Provides basic information about the product.
• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera.

Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site and install it.
The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.

Standard accessories

• Installation Guide (this document)…………………….1 set
• IMPORTANT SAFETY INSTRUCTIONS……………. 1 pc
• CD-ROM*1………………………………………………….. 1 pc.
• Code label*2……………………………………………….. 1 pc.

The CD-ROM contains the operating instructions and different kinds of tool software programs.
This label may be required for network management. Use caution not to lose this label.

The following parts are used during installation procedures.

• Attachment plate…………………………………………. 1 pc.
• Template A (for the attachment plate)…………………..1 sheet
• Power cord plug*3 S2131L S2111L ……………. 1 pc.

*External I/O terminal plug3**

• S2131L ,S2111L………………………………………… 1 pc.
• MONITOR OUT conversion plug…………………….. 1 pc.
• Auxiliary handle S2111L S2130 ………………. 1 pc.
• Bit (WV-S2231L/WV-S2211L only)
• (Hex wrench, screw size 6.35 mm {1/4 inches} T10)….. 1 pc.

3 The external I/O terminal plug and power cord plug are attached to the camera. S2131L S2111L

Preparations

Prepare the required parts for each installation method before starting the installation. The following are the requirements for the various installation methods.

IMPORTANT:

• Procure 4 screws (M4) to secure the attachment plate (accessory) to a ceiling or a wall.

• The minimum required pull-out capacity of a single screw or anchor bolt is 196 N {44 lbf} or more when mounting with the installation method【 Type 1】 or【 Type 2】 described in the right table.

• Select screws according to the material of the location that the camera will be mounted to.
  In this case, wood screws and nails should not be used.

• If the mounting location such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced.

When using WV-Q174B camera ceiling mount bracket, if the built-in microphone port is blocked by the cover of bracket, the collectable volume may decrease and the sound of attic is likely to be collected by mistake. Therefore, please confirm the installation conditions before use. S2130

Installation

The installation tasks are explained using 6 steps.

Remove the camera using the reverse order of the installation procedures.

Step 1 Fixing the attachment plate

There are 2 methods to install the camera to a ceiling or wall.

Common

Note:

•  Attach the attachment plate (accessory) so that the marking (part number) faces toward the ceiling or wall to be installed.

Type

1. Mount the camera on the two-gang junction box using the attachment plate (accessory).
2. Directly mount the camera onto the ceiling or wall using the attachment plate (accessory).
   Align the FRONT direction of the template A (accessory) with the desired direction, and drill through a 25.4 mm {1 inch} diameter hole to attach the attachment plate. Then, the direction of the marker “FRONT⇩” on the camera (see the figure in [3] of “Step 4 Mount the camera”) should face the desired direction of the camera.

1 If the mounting direction of the camera is not determined yet or if you want to change the direction of the camera after it has been installed
If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inches} diameter hole in the center. By doing so you can adjust the mounting direction of the camera in 90° increments.

Step 2 Remove the enclosure from the camera.

1. Remove the enclosure and cushion from the camera.
2. Remove the power cord plug (accessory) and the external I/O terminal plug (accessory) attached to the camera. S2131L S2111L

WV-S2231L / WV-S2211L

• Do not remove the auxiliary wire.

Using the side cable access hole
When installing the camera directly on the ceiling or wall with cables exposed, or when mounting the camera using the ceiling mount bracket WV-Q174B (option), cut out a portion of the dome cover to open a cable access hole.

IMPORTANT:

• To prevent injuries and protect the cables, finish the side cable access hole with a file to avoid sharp edges.

Step 3 Making connections

Refer to the Important Information on the provided CD-ROM for details about each cable.

As necessary, use a cable tie (locally procured) to tie the cables together.

Note:

• Since the connector storage section does not have a sufficient space, use audio cables S2131L S2111L and an Ethernet cable that do not exceed the sizes described in the illustrations.

IMPORTANT:

• Turn off each system’s power supply (PoE hub or device to supply power to the camera) before making a connection.

The 12 V DC power supply shall be insulated from the commercial AC power. S2131L S2111L

1. Connect an Ethernet cable (category 5e or better, straight) to the network connector.

2. If needed, connect a microphone or the line out of an external device to the audio input connector.S2131L S2111L

3. If needed, connect a powered speaker to the audio output connector. S2131L S2111L
   Note:

   • The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on the provided CD-ROM for descriptions of how to switch the output.

4. When connecting an AC adaptor or an external power supply, use the power cable plug (accessory) to connect it to the camera. S2131L S2111L
   Caution:

5. A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

6. ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).

7. Loosen the screw of the power cable plug (accessory), strip 3 mm to 7 mm {1/8 inches to 9/32 inches} from the end of the wire, twist the stripped part of the wire sufficiently to avoid short circuit, and then connect the output cable to the power cable plug (accessory).
   When connecting an external power supply to the camera, use the 16 AWG to 24 AWG singlewired or stranded wired cables.

8. Tighten the screw of the power cable plug (accessory).
   (Recommended tightening torque: 0.34 N·m {0.25 lbf·ft})

9. Connect the power cable plug to the camera.

10. If needed, connect the alarm input/output cables to the EXT I/O terminal plug (accessory). S2131L S2111L
    Connect the cables of external devices to the EXT I/O terminal plug (accessory).

11. When connecting an external device, remove 8 mm – 9 mm {5/16 inches – 11/32 inches} of the outer jacket of the cable and twist the cable core to prevent the short circuit first.
    Specification of cable (wire): 20 AWG – 26 AWG, Single core, twisted

12. Push down the button of the desired terminal on the external I/O terminal plug with a ballpoint pen, and release the button when the cable of the external device is fully inserted into the terminal hole.

External I/O terminal plug

Note:

• Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2 or more wires, use a splitter.
• Check whether the stripped part of the wire is not exposed and is securely connected.
• The default of EXT I/O terminals is “Off”. Refer to the Operating Instructions on the provided CD-ROM for further information about the EXT I/O terminal settings.

Step 4 Mount the camera

1. Align the OPEN mark of the camera side panel with the tab of the attachment plate, insert 2 attachment mounting screws into the attachment plate, and rotate the camera by approximately 15°. The LOCK mark is moved to the tab position of the attachment plate and the camera is temporarily secured.
   The fixing angle of this unit can be adjusted in the interval of 90°.

2. Secure the camera by tightening the camera fixing screw (red).
   IMPORTANT:

   • Be sure to tighten the camera fixing screw. Failure to observe this may cause camera trouble due to camera falling.
     (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})

3. Loosen the cross-head side of tilt table fixing screw (on one side), and incline the tilt table while keeping the TOP mark on the camera lens head facing the front (i.e. the direction of FRONT mark on the camera).

4. Unhook each piece of four nails provided at both sides of the inner cover from the tilting table by pressing surroundings of the PUSH mark of the cover, and remove the inner cover. S2111L S2130
   Note:

   • When using WV-S2231L / WV-S2131L / WV-S2131LRF /WV-S2131LEG / WV-S2131, do not remove the inner cover.

5. Connect the MONITOR OUT conversion plug (accessory) to the MONITOR OUT terminal of the camera, and then connect the monitor for adjustment with a RCA pin cable (locally procured).

6. Insert an SD memory card into the slot, if necessary. S2131L S2111L

   • Refer to the “Important Information” on the provided CD-ROM for how to insert/remove the SD memory card.

Step 5 Adjustment

1. Turn on power for the camera.

2. Loosen the pan table fixing screw.
   Adjust the angle of the camera with the tilt table, pan table, and image tilt adjustment ring.
   Horizontal: +120 ° – -240 °
   Image tilt adjustment range: ±100 °
   WV-S2131/WV-S2130/WV-S2110
   Vertical: ±85 °
   Others
   Vertical: +85 ° – -30 °
   Note:

   • When mounting the camera on a ceiling, adjust the tilt angle so that the TOP mark above the lens always comes to the top side.
   • When mounting the camera on a wall, rotate the pan table by 180° to the left and rotate the tilt table till the TOP mark above the lens always comes to the top side.

3. Tighten the cross-head side of tilt table fixing screw (on one side) and the pan table fixing screw, and fix the camera.
   (Recommended tightening torque:
   0.59 N·m {0.44 lbf·ft}) S2111L S2130

4. Adjust the zoom and focus.

5. Loosen the zoom knob equipped with auxiliary handle (accessory) by rotating the knob to the left, and move it between TELE and WIDE to obtain the appropriate angle of view. Then, lock the zoom knob by rotating it back to the right.

6. Adjust the focus by pressing the auto focus (AF) button. S2111L S2130

7. Adjust the screen size and focus by repeating steps A and B. Readjust the angle of the camera with the tilt table, pan table, and azimuth adjustment ring if necessary.
   After the adjustment, remove the auxiliary handle (accessory).S2111L S2130

8. Press the PUSH mark on both sides of the inner cover, and install the inner cover to the place where it was removed.

9. Disconnect the MONITOR OUT conversion plug (accessory).
   Attach the enclosure and secure it by tightening the enclosure fixing screws (For WV-S2231L/WV-S2211L, use a bit (accessory) to tighten the screws.).
   Attach the enclosure by aligning the i-PRO logo to the direction marker (FRONT ) on the camera.
   (Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}) Adjust the zoom and focus.

10. adjust the viewing angle by pressing the WIDE or TELE buttons.

11. Adjust the focus by pressing the auto focus (AF) button.

12. Adjust the screen size and focus by repeating steps A and B. Readjust the angle of the camera with the tilt table, pan table, and azimuth adjustment ring if necessary.

13. After complete installation, remove the protection film from the dome cover.

Step 6 Configure the network settings
Download and start [IP Setting Software] or [i-PRO Configuration Tool (iCT)] on our technical information support site
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information), and connect to the network.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>