ANKER A1634 Powerbank and Dual USB Wall Charger Instructions
- June 12, 2024
- Anker
Table of Contents
A1634 Powerbank and Dual USB Wall
Charger Instructions
Important Safety Instructions
When using this product, basic precautions should always be followed:
- Store this product in a cool and dry place.
- Do not store this product in a hot or humid environment.
- Using a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or personal injury.
- Operating temperature should be between 32 to 95°F / 0 to 35°C.
- Do not disassemble this product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or personal injury.
- If this product is not used for an extended period, you should charge and discharge it once every three months.
- When charging a device, this product may feel warm. This is a normal operating condition and should not be a cause for concern.
- Under normal operating conditions, the battery performance will decline over several years.
- Do not expose the product to heat or fire.
- Do not clean this product with harmful chemicals or detergents.
- Misuse, dropping, or excessive force may cause product damage.
- When disposing of secondary cells or batteries, keep those of different electrochemical systems separate.
- Beware that a discharged battery may cause fire or smoke.
- CAUTION: There is a risk of explosion if the battery is replaced by an incorrect type.
- WARNING: The batteries (battery pack or installed batteries) shall not be exposed to excessive heat, such as from the sun or fire.
- A battery subjected to extremely low air pressure may result in an explosion or leakage of flammable liquid or gas.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance with Directives 2014/35/EU, 2014/30/EU & 2011/65/ EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance
with Electrical Equipment (Safety) Regulations 2016 & Electromagnetic
Compatibility Regulations 2016 & The Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
The full text of the GB declaration of conformity is available at the
following internet address: https://www.anker.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon,
Hong Kong
The following importers are the responsible parties (contracts for EU and UK
matters):
Anker Technology (UK) Ltd
GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United
Kingdom
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
**** This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from the connected receiver.
- Consult a dealer or an experienced radio / TV technician for help.
Product Name: Anker 511 Power Bank(PowerCore Fusion 30W) Model: A1634
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973
IC Statement
This digital apparatus complies with CAN ICES-3(B)/NMB-3(B).
https://rainbowbridge.anker.com/qrscan?key=anker-221202
Lifetime technical support
18-month limited warranty
Please note that your rights under applicable law governing the sale of
consumer goods remain unaffected by the warranties given in this Limited
Warranty.
support@anker.com
support.mea@anker.com (For Middle East and
Africa Only)
(US/CA) +1 (800)988 7973
(UK) +44 (0) 1604 936200
(DE) +49(0)69 9579 7960
(Middle East & Africa) +971 520750842
(UAE) +971 8000320817
(KSA)+966 8008500030
(Kuwait) +965 22069086 0
(Egypt) +20 8000000826
(AU) +61 3 8331 4800
(TR) +90 (850) 460 14 14
(RU) +8 (800) 511-86-23
(中国) +86 400 0550 036
For FAQs and more information, please visit: anker.com/support
| @anker_offcial @anker_jp
---|---
| @AnkerDeutschland
@AnkerJapan
@Anker
| @Anker Oficial
@Anker_JP
Product Number: A1634 51005003886 V01
PAP22
Raccolta Carta
Documents / Resources
|
ANKER A1634 Powerbank and Dual USB Wall
Charger
[pdf] Instructions
A1634, A1634 Powerbank and Dual USB Wall Charger, Powerbank and Dual USB Wall
Charger, Dual USB Wall Charger, USB Wall Charger, Wall Charger, Charger
---|---