HENN IA19 Crib Labyrinth Instruction Manual
- June 12, 2024
- HENN
Table of Contents
HENN IA19 Crib Labyrinth Instruction Manual
Assembly Requirements
Illustrative images, not included with the product.
NOTICE
To clean your furniture, use a dry or wet cloth, and do not use chemicals
that may damage your product.
ASSEMBLY SYSTEM
The products’ assembly system works according to the increasing order of the
indicated numbers. For example: 01, 02, 03, 04 … to the end of the assembly.
TECHNICAL ASSISTANCE
To request Technical Assistance, the consumer must contact the retailer from whom you purchased this product and request technical assistance for the damaged parts. The warranty covers all parts, parts and components that may eventually present a manufacturing defect within a period of 03 (three) months, counting from the delivery of the product to the consumer, by means of a purchase invoice. If there is any change in the structure of the product or defect occurs due to negligence of the assembler/consumer in relation to the assembly and handling instruction, free technical assistance will not be provided.
WARNING READ WITH ATTENTION AND SAVE FOR EVENTUAL CONSULTATIONS
- Warnings: Do not position or use the product near open fl ame and other sources of heat such as electric heaters, gas heaters or other sources as the material is fl ammable.
- Do not use the crib if any part is broken, torn or missing. Use only replacement parts recommended by the manufacturer.
- Do not leave any object in or near the crib that may serve as a foothold or risk of suffocation, choking or strangulation, such as ropes, blinds / curtain cords, protectors, cushions, toys, wires and cables of electrical appliances.
- Never use more than one mattress in the crib.
- Small children may not play, unattended, in the vicinity of a crib.
- Caution: when the child is able to climb the crib, it can no longer be used by this child, as this crib was built for use by children with motor ability to sit, kneel and / or get up alone but not yet able to climb the crib.
- For cribs with more than one function, not subject to regulation: This product complies with regulations for baby cribs, and its other functions are not subject to regulation.
- This crib can not be altered, either in its structure or in its adornments, because risks to the child’s safety can be generated.
- The length and width of the mattress used with the crib must comply with the specifi cations of this Manual.
Instruction
-
Guidelines: The Brazilian Society of Pediatrics advises to place the baby to sleep on his belly up, as it reduces the risk of sudden death by 70%. We recommend talking to your child’s pediatrician for more information.
-
Only use the crib when fully assembled in accordance with the instructions in the Instruction Manual and after making sure that your locking systems are properly engaged.
-
The crib must be placed on a horizontal fl oor.
-
For cribs with adjustable base height: The lowest position is the safest and the base should always be used in this position as soon as the baby is old enough to sit.
-
When there are detachable supporting devices to support the crib base above its lowest position: Before the crib is used in its lowest position, the devices used to support the crib in the highest positions should be removed.
-
The mounting connections must always be tightened properly and checked regularly, throughout the use of the crib, and retightened as necessary.
-
If any part of the crib breaks or is defective, you should look for expert technical assistanceand no home repairs.
-
Guidelines for the thickness of the mattress, which may be given in the following ways:
a) The length and width of the mattress used with the crib shall be such that it is never possible to form a space greater than 30 mm between the sides or ends and the mattress.
b) The thickness of the mattress shall be such that the inner height (from the mattress surface to the upper edge of the cradle frame) is at least 480 mm in the lowest position of the cradle base and at least 180 mm in the highest position of the cradle of the crib.
c) When a marking is used on the crib to indicate the maximum thickness of the mattress:The marking on the crib indicates the maximum thickness of the mattress to be used with the crib. -
Recommendation on the minimum size of mattress to be used with the crib. For Crib Labirinto, the use of a 1,30 m ± 0.5 cm mattress is recommended length, 60 cm ± 0,5 cm wide and 12 cm ± 0,5 cm high, with a minimum density of 18 kg / m³ ± 2,0 kg / m³ (D18).
THE INMETRO REGISTRATION AND THE CONFORMITY IDENTIFICATION SEAL REFER ONLY TO THE CRIB
A: 8x C: 4x D: 4x E: 4x
Use the screwdriver with the torque at 15 to attach the rail and base frame.
B: 12x
For the higher option the distance between the end base frame to the sides should be 11mm
The end base frames (05) and (06) must be 8,5mm from the fi xed rail (02).
Use the screwdriver with the torque at 15 to attach the rail and base frame.
The distance between ballast should be 10mm
For the lower option the distance between the end base frame to the sides
should be 11mm.
The end base frames (05) and (06) must be 2mm from the fi xed rail (02).
A: 4x
Use the screwdriver with the torque at 15 to attach the rail and base frame.
Base ballasts should not be removed for transportation and / or storage purposes.
List of parts
Item
| Box| Qty| Description| Size (measurements) (mm)
---|---|---|---|---
01| 1/1| 01| Lateral| 866x660x12
02=07| 1/1| 01| Fixed Rail| 1300x670x25
03| 1/1| 01| Side with label| 866x660x12
04| 1/1| 02| Crib Frame| 1301x36x22
05| 1/1| 01| 6mm Larges base Frame with seal| 595x420x6
06| 1/1| 02| 6mm Largest Base Frame| 595x420x6
07=02| 1/1| 01| Fixed Rail| 1300x670x25
Hardware
A: Screw 1/4x50mm PAN.
B: Screw 4,5x25mm CHT.
C: Zamac nut 12×12
D: “U” shoe 12x15mm
E: Ringed Nails 12x12mm