Henn Hart AC1694 Alston Accent Cabinet User Manual

June 17, 2024
Henn Hart

ASSEMBLY INSTRUCTIONS
Henn Hart AC1694 Alston Accent Cabinet ACCENT CABINET

PRE-ASSEMBLY:

Two people are recommended to assemble this furniture.
Carefully remove all parts and hardware from carton, along with any protective packaging.
Locate and set aside the hardware kit before discarding packaging.
Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
Assemble the furniture on a soft surface, and take extra care not to scratch or damage parts during the assembly.
Save these instructions
Made in China
AC1694 AC1695 AC1906 AC1907
AC1935 AC1936 rev052523EFS FG2B
PRECAUTIONS — READ ALL BEFORE BEGINNING ASSEMBLY
Do not place items on the shelf which exceed the maximum weight limits of:
Top shelf: 45 lbs. (20.4 kg)
Middle Shelf: 25 lbs. (11.3 kg)
Bottom Shelf: 35 lbs. (15.9 kg)
Usage with loads heavier than the maximum weights specified may result in instability, causing tip-over and
resulting in death or serious injury.
When in use, this furniture must be placed on a flat, solid and level surface.
Do not climb or step on the shelves.
Remove ALL items from the furniture before attempting to move the furniture.
Do not use a drill or power tools to assemble this furniture, as it may weaken or damage parts.

PARTS

Henn Hart AC1694 Alston Accent Cabinet - PARTS NOTE: This illustration is for parts identification/orientation purposes only. For assembly, see following pages.Henn Hart AC1694 Alston Accent
Cabinet - PARTS 2

HARDWARE

Henn Hart AC1694 Alston Accent Cabinet - PARTS 3

TIPPING RESTRAINT HARDWARE

Henn Hart AC1694 Alston Accent Cabinet - PARTS 4 (See pages 22-24 for installation)
CARE INSTRUCTIONS:

  • Wipe clean with a soft, dry cloth or static duster.
  • Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the table’s finish.
  • Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if necessary.

INSTALLING THE CAM LOCKS

Screw the Cam Screw into the prethreaded hole. Tighten with a screwdriver until snug.Henn Hart AC1694 Alston Accent Cabinet - assembly
1The base of the Cam Screw should be flush with the panel.

       Connect the panels. Insert the Cam Screw into the small hole in the adjoining panel. Henn Hart AC1694 Alston Accent Cabinet - assembly
3The head of the Cam Screw should be visible through the large hole. Henn Hart AC1694 Alston Accent Cabinet - assembly
4Insert the Cam Lock into the large hole. Make sure the arrow and the opening in the Cam Lock are facing the Cam Screw. Henn Hart AC1694 Alston Accent Cabinet - assembly 5Using a screwdriver, turn the Cam Lock at least 90° clockwise to lock the two panels firmly together.Henn Hart AC1694 Alston Accent
Cabinet - assembly 6MAKE SURE THE ASSEMBLY IS DONE ON A LEVEL AND SOFT SURFACE (SUCH AS BLANKETS)
TO PREVENT DAMAGING THE PARTS DURING ASSEMBLY.Henn Hart AC1694 Alston Accent
Cabinet - assembly 7 NOTE: DO NOT OVERTIGHTEN SCREWS.Henn Hart AC1694 Alston Accent Cabinet - assembly
8Henn Hart AC1694 Alston Accent Cabinet -
assembly 9![Henn Hart AC1694 Alston Accent Cabinet

  • assembly 10](https://manuals.plus/wp-content/uploads/2024/02/Henn-Hart- AC1694-Alston-Accent-Cabinet-assembly-10.png)Henn Hart AC1694 Alston Accent
Cabinet - assembly 11Henn Hart AC1694 Alston
Accent Cabinet - assembly 12Henn Hart AC1694
Alston Accent Cabinet - assembly 13 NOTE: DO NOT OVERTIGHTEN SCREWS.
    An assistant is recommended to HOLD the cabinet backing (H) in place while installing screws (6) into the pilot holes.
    DO NOT TO OVERTIGHTEN SCREWS. Align cabinet backing (H) with cabinet frame before continuing.Henn Hart AC1694 Alston Accent Cabinet - assembly
14 An assistant is recommended to HOLD the cabinet backing (H) in place while installing screws (6).
    DO NOT TO OVERTIGHTEN SCREWS.Henn Hart AC1694 Alston Accent Cabinet -
assembly 15 With the help of an assistant, turn accent cabinet upright.Henn Hart AC1694 Alston Accent Cabinet - assembly
16Henn Hart AC1694 Alston Accent Cabinet -
assembly 17 NOTE: DO NOT OVERTIGHTEN SCREWS.Henn Hart AC1694 Alston Accent Cabinet - assembly
18 NOTE: DO NOT OVERTIGHTEN SCREWS.
    SEE PAGE 21 FOR DOOR ALIGNMENT INSTRUCTIONS.
    FinishedHenn Hart AC1694 Alston Accent Cabinet - assembly
19 NOTE: Use the leveling feet to make sure furniture is level on the floor before using.
    NOTE: USE THE LEVELING FEET TO MAKE SURE FURNITURE IS LEVEL ON THE FLOOR BEFORE USING. LEVELING THE CABINET MAY AFFECT THE LEVEL OF THE DOORS. SEE NEXT PAGE FOR DOOR ALIGNMENT INSTRUCTIONS. REMOVE ALL ITEMS FROM CABINET BEFORE ADJUSTING THE LEVELING FEET.

Adjusting the doors

IMPORTANT — The furniture MUST be level on a flat, solid floor surface for the doors to work properly. Remove all items from furniture, then turn the leveling feet under the cabinet to make sure the furniture is level. Once the furniture is level, align the doors as shown for proper operation.

FRONT VIEW

** UP AND DOWN
Use screws to adjust the gaps at the top and bottom of door.Henn Hart AC1694
Alston Accent Cabinet - assembly 22
FRONT VIEW**

LEFT AND RIGHT
Use screw to adjust the gaps at left and right of the door. TOP VIEWHenn
Hart AC1694 Alston Accent Cabinet - assembly 25 IN AND OUT
Use screw to move the door in or out.![Henn Hart AC1694 Alston Accent Cabinet

FURNITURE TIPPING RESTRAINT

WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Manufacturer assumes no liability for improper installation or excessive loads placed on screws, brackets, or straps. Young children may be injured by tipping furniture and the use of a tipping restraint is required. Never climb or step on shelves.
When properly installed, this restraint will provide protection against tipping of furniture. This tipping restraint must be secured to a wall-stud or wall structure of similar strength.
Note: For safe mounting it is essential to use the proper hardware for your wall type. The included hardware is for drywall or wood stud mounting only. For other wall types (e.g., metal studs, plaster, concrete, and brick) please consult your local hardware store for fastener advice.
Hardware included:Henn Hart AC1694 Alston Accent Cabinet - Hardware
included See next page for installation instructions

FURNITURE TIPPING RESTRAINT

Henn Hart AC1694 Alston Accent Cabinet - assembly 27 NOTE: DO NOT OVERTIGHTEN SCREWS.
FURNITURE TIPPING RESTRAINTHenn Hart AC1694 Alston Accent Cabinet -
assembly 28

  1. Hold Bracket (K1) up to the wall and mark hole locations using a pencil.
  2. Drill pilot holes 1-1/4″ deep. Use only Screws (K2) if going directly into wood studs. If going into drywall (no stud), use Wall Anchors (K3) with Large Screws (K2).
  3. Install Bracket (K1) and make sure securely fastened.
  4. Install zip tie (K4) and wrap around furniture and tighten.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals