MAYFAIR 238002 Exterior Wall Down Light Bracket Instruction Manual

June 12, 2024
MAYFAIR

Installation Instructions
SEASIDE WALL DOWNLIGHT
SKU# 238002, 230092
Rated Voltage 220-240V~ 50Hz

To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this luminaire. Please keep instructions for future reference.

Warranty

  • This luminaire is covered by a 5-year warranty. The warranty is from date of purchase, not the date of installation.
  • If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
  • Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
  • Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
  • Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

  • This luminaire must be assembled and installed by a licensed electrician.

  • All wiring and installation of the luminaire must adhere to the latest local and national wiring rules. E.g. AS/NZS 3000 Electrical Installations.

  • This luminaire is a Class I product and must be earthed during wiring and installation.

  • This luminaire is rated IP65, this must be maintained during wiring and installation

  • Do not exceed the maximum wattage rating.

  • Select a suitable location for installation:
    − The mounting point must support 2 times the weight of the luminaire.
    − This luminaire is protected against water penetration to IP65 standards, which is against low-pressure jets of water from all practicable directions.

  • The luminaire must not be used if the protective shield has cracked. Replace any cracked protective shield before using the luminaire.

  • Take care not to pull any electrical wires during unpacking as this may damage the connection.

  • Lay out all the components on a smooth surface and make sure no components are missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.

  • Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

  • Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

  1. Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

  2. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.

  3. Remove the mounting bracket (E) by loosening the grub screws (F) on the side, with the supplied Allen key (G).

  4. Use the mounting bracket (E) as a template to mark the screw positions on the wall.

  5. Install the mounting bracket (E) onto the wall by using appropriately sized mounting screws (C), sealing rubber washers (D), mounting gasket (H) and anchors (I). Ensure the screws (C) and anchors (I) used are suitable for the mounting surface and the surrounding environment.
    NOTE: A non-corrosive bead of silicon MUST be applied before installation onto the wall, ensuring that no water can run down into the cabling.

  6. Connect the mains supply wire to the terminal block (B). Ensure the wires are secure and no bare wires are exposed.
    Mains Supply Wire| Luminaire Wire / Terminal label
    ---|---
    Earth – Yellow/Green | Yellow/Green or
    Neutral – Blue or Black| Blue or N
    Live – Brown or Red| Brown or L

NOTE: This luminaire is a Class I product and must be earthed during wiring and installation.

  1. Install the luminaire (A) back onto the mounting bracket (E) and secure by tightening the grub screws (F).
  2. Remove the shade (K) from the luminaire (A) by twisting it anti-clockwise.
  3. Install a globe (J – not included) into the lamp holder. Do not exceed the maximum wattage rating.
  4. Install the shade back (J) onto the luminaire (A) and secure by twisting it clockwise
  5. After the installation, switch on the luminaire to test all the lighting functions and enjoy your new luminaire.

MAYFAIR 238002 Exterior Wall Down Light Bracket - Fig1

Safety Tips

  • Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
  • To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
  • To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
  • Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
  • The luminaire must not be used if the protective shield has cracked. Replace any cracked protective shield before using the luminaire again.

Specifications

SKU # 238002 230092
Colour Aged Solid Bronze Solid Brass
Rated Voltage 220-240V— 50Hz
Rated Wattage 28W Max.
Lamp Holder GU10
IP Rating IP65
Weight 0.9kg
Dimensions H:128mm W:75mm E:85mm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals