ZKTeco MB20-VL Time Clock With Ultra Fast Facial Recognition And Fingerprint Reader User Guide

ZKTeco MB20-VL Time Clock With Ultra Fast Facial Recognition And Fingerprint Reader

Overview

Note: Features and parameters with mark are not available in all devices.

Device Installation

Install on the wall

1. Attach the mounting template sticker to the wall, and drill holes according to the mounting paper.
   

2. Fix the back plate on the wall using wall mounting screws.
   

3. After passing the wires through the wiring hole and connecting them to the device, and then attach the device to the back plate from top to bottom.
   

4. Fasten the device to the back plate with a security screw.
   

Standalone Installation

Door Sensor & Exit Button Connection

Lock Relay Connection

The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when powered) is connected with ‘NO’ and ‘COM’ terminals, and the NC LOCK (normally locked when powered) is connected with ‘NC’ and ‘COM’ terminals. Take NC Lock as an example below:

Not sharing power with the lock

Power Connection

• Recommended AC adapter: 5V, 2A
• To share the power with other devices, use an AC adapter with higher current ratings.

Ethernet Connection

Connect the device and computer software over an Ethernet cable. As shown in the example below:

Click on [Comm.] > [Ethernet] > [IP Address], input the IP address and click on [OK].

Note: In LAN, the IP addresses of the server (PC) and the device must be in the same network segment while connecting to the ZK BioAccess IVS software.

Quick Start

User registration

Method 1: Registering on the device

Press [M/OK] > [Main Menu] > [User Mgt.] > [New User]. Enter User ID, Name, User Role, Department, Verification Mode and register Face, Fingerprint, Card Number★ and Password,to register a user.

Method 2: Registering on the software (ZK BioAccess IVS)

Please set the IP address and cloud service server address in the Comm. Menu option on the device.

1. Click [Attendance] > [Attendance Device] > [Device] > [Search] to search the device on the software. When an appropriate server address and port is set on the device, the searched devices are displayed automatically.
   

2. Click [Add]in operation column, a new window will pop-up. Select Attendance Area and Time zone from each dropdowns and click [OK] to add the device.

3. Click [Personnel] > [Person] > [New] and fill in all the required fields to register a new users in the software.

4. . Click [Attendance Device] > [Device] > [Control] > [Synchronize Software Data to the Device] to synchronize all the data to the device including the new users.

For more details, please refer to the ZKBioAccess IVS User Manual.

Method 3: Registering on the phone

Once the ZKBioAccess IVS software is installed, the users could enroll their face via a browser application on their own mobile phone.

1. Click [Personnel] > [Parameters], input ‘’http://server.address: Port’’in the QR Code UGL bar. The software will automatically generate a QR code. Scan the QR code or login onto‘’http://Server.address: Port/app/v1/adreg’’by the mobile phone to register users.
   

2. The users will be displayed in [Personnel] > [Pending Review], click on [Review] option andassignadepartmentandclick[OK]to successfully add the user.

User Authentication

The terminal can detect the face within a range of 0.3m to 1.5m.The device switches to the face verification interface automatically once it detects a change in environmental brightness.The verification result shows the personnel details.

View records

View records on the software
Click [Device] > [Data] > [Transaction] on the software to view the records.

Access Control Settings

Press [M/OK] > [Access Control] to enter the access control management interface and set relevant parameters of access control.

Ethernet and Cloud Server Settings

Press [M/OK] > [Comm.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface.

Press [M/OK] > [Comm.] > [Cloud Server Setting] to set the server address and server port, that is, the IP address and port number of the server after the software is installed. If the device communicates with the server successfully, the icon will be displayed in the upper right corner of the standby interface.

 Customers Support

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 – 82109991
Fax : +86 755 – 89602394
www.zkteco.com

References

• ZKTeco | Biometrics and Computer Vision

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>