saxby lighting 78541 SirioDISC Adjustable Downlight Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

saxby lighting 78541 SirioDISC Adjustable Downlight Instruction Manual
Warning
Layout
Installation
Wiring
Check that…
Technical data
- Supply Voltage:
Care and Safety

saxby lighting 78541 SirioDISC Adjustable Downlight Instruction Manual

Thank you for purchasing this light ﬁtting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.

Warning

This power supply is double insulated and does not require connection to an Earth circuit.
Luminaires not suitable for covering with thermally insulating material.Please read these instructions carefully before commencing any work. This unit must be ﬁtted by a competent and qualiﬁed electrician.

Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.This fitting must always be fitted to a plasterboard ceiling. This must not be fitted to a plaster and lath ceiling.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross section area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking.
The distance between units must be 0.5m minimum.
There is at least 0.2mm distance between the lamp and the inflammable materials. This product must be mounted out of arms reach.

Installation

Existing ﬁttings must be completely removed before installation of a new product. Before removing the existing ﬁtting, carefully note the position of each set of wires.
Note that the power needs to be isolated/switched off at the fuse board. The ceiling surface must be flat and smooth to ensure a good fit.
This product can be recessed mounted and surface mounted on the ceiling.

Spring adjustable instruction refer to Fig 1.
Recessed mounted refer to Fig 2. cut a 65-205mm hole using an appropriate It is recommended to cut the hole slightly smaller than needed, then file the hole until the recessed unit fits snugly. Ensure that the void depth is a minimum of 15mm.
Ensure that the product is sitting properly in the
Surface mounted refer to Fig 3. Ensure the bracket is fixed on the ceiling
Wiring as detailed wiring
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Wiring

Having correctly identified the wiring from your light fitting, pull the wire through the hole and connect to the connection block in the following way:
This unit is double insulated and mud not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.

Check that…

You have correctly identiﬁed the
The connections are

No loose strands have been left out of the connection block.

Technical data

Supply Voltage:

Bulb 220-240 V~, 50 Hz
Type: 18W LED module (SMD), 4000K
This product contains a light source of energy efficiency class F.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the ﬁnish. For your safety, always switch off the power supply before cleaning.
For further information, please visit https://www.lighting- info.co.uk/78541

V2 18/12/2021

UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg