Hotpoint AH12H15D5B PTAC Heat Pump Unit Instructions

Hotpoint AH12H15D5B PTAC Heat Pump Unit

Product Information

Product Model: AH12H15D5B
Dimensions and Installation Information:

• Wall Case Dimensions:
  • A: 30 inches
  • C: 70 inches
• Maximum Cord Extension: 30 inches
• Wall Opening Dimensions: Add 1/4 to A and C dimensions for all cut-outs. RAB80 16-1/4 Min. H x 42-1/4 Min. W

AH12 ELECTRIC HEATER 230/208 VOLT LINE CORD CONNECTED UNITS:

• Heater Watts: 5,000 / 4,100
• Heater BTU: 15,000 / 12,200
• Heater Amps: 22.3 / 20.1
• Min Circuit: 30
• Recommended Protective Device: 30 amp time-delay fuse or breaker

AH12 HEAT PUMP:

• Heat Pump Watts: 1180 / 1120
• Heat Pump BTU: 13,400 / 13,100
• COP: 3.2

Product Usage Instructions

To install the AH12H15D5B unit, follow these steps:

1. Measure and mark the wall opening dimensions, adding an extra 1/4 inch to the A and C dimensions for all cut-outs.
2. Ensure the wall case dimensions match the specified dimensions for the unit.
3. Connect the line cord to a 230/208 volt power source.
4. For electric heating, ensure the unit is connected to a circuit with a minimum rating of 30 amps.
5. Install a 30 amp time-delay fuse or breaker as the recommended protective device.
6. If using the AH12 as a heat pump, connect it to a power source with the appropriate wattage and voltage.
7. Refer to the product manual for further instructions on configuring and operating the AH12H15D5B unit.

DIMENSIONS AND INSTALLATION INFORMATION

WALL CASE DIMENSIONS
RAB80 WALL SLEEVE Heavy-gauge galvanized steel, with insulation, for quick self-assembly. A – 42”, B – 13-3/4”, C – 16”

MAXIMUM CORD EXTENSION
WALL OPENING DIMENSIONS Add 1/4” to A and C dimensions for all cut-outs. RAB80 16-1/4” Min. H x 42-1/4” Min. W

ELECTRICAL WIRING

All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations.
NOTE : Aluminum wiring may pose special problems – consult a qualified electrician.

GRILLE OPTIONS

• Stamped Aluminum Grille – RAG70

ELECTRICAL CONNECTION

• 230/208 volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
• Power cord is permanently attached on all Hotpoint chassis

SPECIFICATION

AH12 ELECTRIC HEATER

230/208 VOLT| LINE CORD CONNECTED UNITS
Heater Watts| 5,000 / 4,100
Heater BTU| 15,000 / 12,200
Heater Amps| 22.3 / 20.1
Min Circuit| 30
Recommended protective Device| 30 amp time-delay fuse or breaker
AH12 HEAT PUMP
Heat Pump Watts| 1180 / 1120
Heat Pump BTU| 13,400 / 13,100
COP| 3.2

FEATURE AND BENEFITS

• 14,800 / 14,600 cooling BTU
• 10.6 EER
• 13,400 / 13,100 heating BTU
• 3.2 COP
• R32 Refrigerant – Environmental friendly, low GWP (Global Warming Potential)
• 3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
• 4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
• Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
• Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
• Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
• Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
• Auto Power Recovery – In case of power failures, units automatically resume their operation when power restores, reducing maintenance calls
• Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
• Backed by an Industry Leader – With a long history of creating durable products at an affordable price, Hotpoint is your trusted PTAC brand

PRELIMINARY SPECIFICATIONS – SUBJECT TO CHANGE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>