AV Access 4KEX70-H2 HDMI 2.0 Over HDBaseT Extender User Manual

: June 12, 2024
: AV Access

Table of Contents

AV Access 4KEX70-H2 HDMI 2.0 Over HDBaseT Extender
Product Information
Product Usage Instructions
Introduction
Panel
Installation and Application
Operate with RS232
Specification
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AV Access 4KEX70-H2 HDMI 2.0 Over HDBaseT Extender

AV-Access-4KEX70-H2-HDMI-2.0-Over-HDBaseT-Extender-product-
image

Product Information

The HDMI 2.0 Over HDBaseT Extender (model number 4KEX70-H2) is a device that allows you to extend HDMI signals over long distances using HDBaseT technology. It supports HDMI 2.0 with 4K@60Hz 4:4:4 8bit and HDCP 2.2, as well as HDR (High Dynamic Range) format. The extender can transmit a 1080P signal up to 70m/230ft and a 4K signal up to 40m/131ft using a Cat 6a/7 cable. It can also transmit a 1080P signal up to 60m/197ft and a 4K signal up to 35m/115ft using a Cat 5e/6 cable. The extender features bi-directional PoE (Power over Ethernet), allowing you to power both the transmitter and receiver units using a single power adapter. It also supports bi-directional IR/RS232 pass through and has a slim profile for easy installation.

Package Contents:

Transmitter x 1
Receiver x 1
Power Adapter (DC 18V 1A) x 1
IR Emitter x 1
Broadband IR Receiver (30-50 KHz) x 1
Mounting Bracket (with Screws) x 4
Phoenix Male Connector (3.5mm, 3 Pins) x 2
User Manual x 1

Transmitter Panel:
Front Panel:

No.	Name	Description
1	Power LED	On: The device is powered on. Off: The device is powered

off.
2| Status LED| Blinking: The device is working properly. Off: The device is
not working properly. On: HDCP protected content is being
transmitted.
3| HDCP LED| Blinking: Non-HDCP protected content is being transmitted. Off:
No HDMI signal is being transmitted.
4| Link LED| On: HDBT link is normal. Blinking/Off: No link or link
error.

Rear Panel:

No.	Name	Description
1	DC 18V	Connect to the DC 18V power adapter provided. Note: With

Receiver Panel:
Front Panel:

No.	Name	Description
1	Power LED	ON: The device is powered on. OFF: The device is powered

off.
2| Status LED| Blinking: The device is working properly. OFF: The device is
not working properly. ON: HDCP protected content is being
transmitted.
3| HDCP LED| Blinking: Non-HDCP protected content is being transmitted. OFF:
No content is being transmitted.

Product Usage Instructions

Ensure that you have all the package contents mentioned above.
Install the mounting brackets using the provided screws, if necessary.
Connect the DC 18V power adapter to either the transmitter or receiver unit.
Connect the HDBT Out port on the transmitter to the receiver using a Cat 5e/6/6a/7 cable.
Connect the IR In port on the transmitter to the provided IR receiver.
Connect the IR Out port on the transmitter to the provided IR emitter.
Connect the RS232 port on the transmitter to an RS232 enabled device, if needed.
Connect the HDMI In port on the transmitter to an HDMI source device.
Repeat steps 4-8 for the receiver unit, if necessary.
Ensure that all connections are secure and properly plugged in.
Power on the devices using the power LED indicator as a reference.
Verify that the status LED indicators are blinking, indicating proper device operation.

Note: For HDCP protected content, ensure that the HDCP LED indicator is on.

Introduction

Overview
This product is a slim HDBT transmitter receiver set. It supports resolutions up to 4K@60Hz 4:4:4 8bit and HDCP 2.2 compatibility, transmitting HDMI signals up to 40m/131ft at 4K and up to 70m/230ft at 1080P via a Cat 6a/7 cable. It also provides bi-directional PoE, enabling only one power adapter connected to either transmitter or receiver to power both units. Bi-directional IR pass- through allows you to control the source at the display side or control the display at the source side. It also features RS232 pass-through for serial communication.
The transmitter and receiver are easy to install. They are space saving and offering ideal solutions for homes, offices, digital entertainment centers, control centers, conference rooms, schools and corporate training environments.

Features

Supports HDMI 2.0 with 4K@60Hz 4:4:4 8bit and HDCP 2.2.
Supports HDR (High Dynamic Range) format.
Via a Cat 6a/7 cable, transmitting 1080P signal up to 70m/230ft and 4K signal up to 40m/131ft.
Via a Cat 5e/6 cable, transmitting 1080P signal up to 60m/197ft and 4K signal up to 35m/115ft.
Bi-directional PoE, one power adapter is needed to be connected to either transmitter or receiver side to power both units.
Bi-directional IR/RS232 pass through.
Slim profile, space saving and easy-to-install.

Panel

Transmitter

AV-Access-4KEX70-H2-HDMI-2.0-Over-HDBaseT-Extender-01

No.	Name	Description
1	Power LED

On: The device is powered on.
Off: The device is powered off.

2| Status LED|

Blinking: The device is working properly.
Off: The device is not working properly.

3| HDCP LED|

On: HDCP protected content is being transmitted. Blinking: Non-HDCP protected content is being transmitted.
Off: No HDMI signal is being transmitted.

4| Link LED|

On: HDBT link is normal.
Blinking/Off: No link or link error.

AV-Access-4KEX70-H2-HDMI-2.0-Over-HDBaseT-Extender-02

No.	Name	Description
1	DC 18V	Connect to the DC 18V power adapter provided.

Receiver AV-Access-4KEX70-H2-HDMI-2.0-Over-HDBaseT-
Extender-03

No.	Name	Description
1	Power LED

ON: The device is powered on.
OFF: The device is powered off.

2| Status LED|

Blinking: The device is working properly.
OFF: The device is not working properly.

3

|

HDCP LED

|

ON: HDCP protected content is being transmitted.
Blinking: Non-HDCP protected content is being transmitted.
OFF: No content is being transmitted.

4| Link LED|

ON : HDBT link is normal.
OFF: No HDBT link or link error.

AV-Access-4KEX70-H2-HDMI-2.0-Over-HDBaseT-Extender-04

No.	Name	Description
1	DC 18V	Connect to a DC 18V 1A power adapter.

Installation and Application

Brackets Installation
Note: Before installation, please ensure the device is disconnected from the power source.

Position and install the mounting brackets with the four mounting screws provided.
Mount and secure the transmitter/receiver to a surface or a suitable location with the mounting screws (not included in the package).

Application

Note:

Ensure the Cat x cable’s length is within the maximum transmission distance (Detail information, please refer to “Specification” section).
With bi-directional PoE function supported, one power adapter is needed to be connected to the transmitter or receiver to power both units.

Operate with RS232

According to the bi-direction RS232 pass through function, users can use RS232 control system and RS232 controlled device for serial communication by connecting to the devices via serial cables.

Specification

Technical

Video Signal Type| HDMI 2.0 with 4K@60Hz 4:4:4 8bit, HDCP 2.2
| SMPTE:
| 1280x720P1,2,3,4,5,6,7,8,1920x1080I6,8,
| 1920x1080P1,2,3,4,5,6,7,8, 3840×21602,3,5,6,8,
| 4096×21602,3,5,6,8
| VESA:
Input/ Output Resolution Supported| 800×6008, 1024×7688, 1280×7688, 1280×8008, 1280×9608, 1280×10248, 1360×7688, 1366×7688, 1400×10508,
| 1440×9008, 1600×9008, 1600×12008,
| 1680×10508, 1920×12008
| 1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at
| 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94
| Hz, 8 = at 60 Hz
Audio Format Supported| Stereo, PCM 2.0/5.1/7.1, Dolby True HD and DTS HD Master Audio
Maximum Data Rate| 18Gbps
General

Operating Temperature| 0°C to 45°C (32°F to 113°F)
Storage Temperature| -20°C to 70°C (-4°F to 158°F)
Humidity| 10% to 90%, non-condensing
ESD Protection| ±8kV (Air-gap discharge)/ ±4kV (Contact discharge)
Surge Protection| Voltage: ±1 kV
Power Consumption (Max)| 12.8W (Pair)
Device Dimension (W x H x D)|

Transmitter: 136.4 mm ×15.2 mm × 74.2 mm/5.37” x 0.60” x 2.92”
Receiver: 150mm x 20mm x 74.2mm/5.90” x 0.79” x 2.92”

Product Weight|

Transmitter: 0.24kg/0.53lb
Receiver: 0.36kg/0.79lb

Transmission Distance
Note: We recommend the use of T568B straight-through category cables.

Cable Type	Range	Supported Video
Cat 5e/6	60m/197ft	1080P@60Hz 36bpp
35m/115ft

1080P@60Hz 48bpp
1080P@60Hz 3D
4K@60 Hz 4:4:4 with HDR

Cat 6a/7| 70m/230ft| 1080P@60Hz 36bpp
40m/131ft|

1080P@60Hz 48bpp
1080P@60Hz 3D
4K@60Hz 4:4:4 with HDR

HDMI| Input/Output: 15m/49ft| 1080P@60Hz
Input/Output:10m/33ft| 4K@30Hz

Input: 3m/10ft
Output: 5m/16ft

| 4K@60Hz

Warranty

Products are backed by a limited 1-year parts and labor warranty. For the following cases AV Access Technology Limited shall charge for the service(s) claimed for the product if the product is still remediable and the warranty card becomes unenforceable or inapplicable.

The original serial number (specified by AV Access Technology Limited) labeled on the product has been removed, erased, replaced, defaced or is illegible.
The warranty has expired.
The defects are caused by the fact that the product is repaired, dismantled or altered by anyone that is not from an AV Access Technology Limited authorized service partner. The defects are caused by the fact that the product is used or handled improperly, roughly or not as instructed in the applicable User Guide.
The defects are caused by any force majeure including but not limited to accidents, fire, earthquake, lightning, tsunami and war.
The service, configuration and gifts promised by salesman only but not covered by normal contract.
AV Access Technology Limited preserves the right for interpretation of these cases above and to make changes to them at any time without notice.

Thank you for choosing products from AV Access.
If you have any question, please contact us via the following emails: