Hotpoint AH12H09D2B PTAC Heat Pump Unit with Electric Heat Backup Instruction Manual

Hotpoint AH12H09D2B PTAC Heat Pump Unit with Electric Heat Backup

Product Information

Product Model : AH12H09D2B

Dimensions:

• Wall Case Dimensions (in inches): A = 30, C = 70
• Wall Opening Dimensions (in inches): RAB80 16-1/4 Min. H x 42-1/4 Min. W

Electric Heater:

• Voltage: 230/208 Volt
• Line Cord Connected Units
• Heater Watts: 2,580 / 2,150
• Heater BTU: 7,800 / 6,300
• Heater Amps: 11.3 / 10.3
• Minimum Circuit: 15 Amps
• Recommended Protective Device: 15 Amp Time-Delay Fuse or Breaker

Heat Pump:

• Heat Pump Watts: 720 / 690
• Heat Pump BTU: 8,400 / 8,200
• COP (Coefficient of Performance): 3.4

Product Usage Instructions

To install the AH12H09D2B unit, follow these steps:

1. Determine the wall opening dimensions by adding 1/4 inch to the A and C dimensions.
2. Cut out a wall opening with the determined dimensions.
3. Place the wall case into the opening and secure it properly.
4. Connect the line cord to an appropriate power source with a minimum circuit of 15 amps.
5. If using the electric heater function, ensure that the recommended protective device (15 amp time-delay fuse or breaker) is installed.
6. For heat pump operation, connect the heat pump to the appropriate power source.

For further assistance or troubleshooting, refer to the complete user manual or contact customer support.

DIMENSIONS AND INSTALLATION

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

ELECTRICAL WIRING

All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations.
NOTE : Aluminum wiring may pose special problems – consult a qualified electrician

GRILLE OPTIONS

• Stamped Aluminum Grille – RAG70

ELECTRICAL CONNECTION

• 230/208 volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
• Power cord is permanently attached on all Hotpoint chassis.

WALL CASE DIMENSIONS

RAB80 WALL SLEEVE
Heavy-gauge galvanized steel, with insulation, for quick self-assembly. A – 42”, B – 13-3/4”, C – 16”

MAXIMUM CORD EXTENSION
WALL OPENING DIMENSIONS Add 1/4” to A and C dimensions for all cut-outs. RAB80 16-1/4” Min. H x 42-1/4” Min. W

SPECIFICATION

AH12 ELECTRIC HEATER

230/208 VOLT| LINE CORD CONNECTED UNITS
Heater Watts| 2,580 / 2,150
Heater BTU| 7,800 / 6,300
Heater Amps| 11.3 / 10.3
Min Circuit| 15
Recommended protective Device| 15 amp time-delay fuse or breaker
AH12 HEAT PUMP
Heat Pump Watts| 720 / 690
Heat Pump BTU| 8,400 / 8,200
COP| 3.4

FEATURE AND BENEFITS

• 9,500 / 9,500 cooling BTU
• 11.4 EER
• 8,400 / 8,200 heating BTU
• 3.4 COP
• R32 Refrigerant – Environmental friendly, low GWP (Global Warming Potential)
• 3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
• 4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
• Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
• Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
• Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
• Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
• Auto Power Recovery – In case of power failures, units automatically resume their operation when power restores, reducing maintenance calls
• Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
• Backed by an Industry Leader – With a long history of creating durable products at an affordable price, Hotpoint is your trusted PTAC brand

PRELIMINARY SPECIFICATIONS – SUBJECT TO CHANGE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>