Hotpoint AH12E07D2B PTAC with Electric Heat Instruction Manual

Table of Contents

Hotpoint-AH12E07D2B-PTAC-with-Electric-Heat-PRODUCT

Product Information

Product Model: AH12E07D2B

Dimensions and Installation Information:

Wall Case Dimensions:
- A: 30 inches
- C: 70 inches
Maximum Cord Extension: 30 inches
Wall Opening Dimensions: Add 1/4 to A and C dimensions for all cut-outs. RAB80 16-1/4 Min. H x 42-1/4 Min. W

AH12 ELECTRIC HEATER 230/208 VOLT LINE CORD CONNECTED UNITS:

To install the AH12E07D2B electric heater, follow the steps below:

Measure the wall case dimensions (A and C) and ensure they match the requirements of the product.
Determine the maximum cord extension needed, which should not exceed 30 inches.
Prepare the wall opening by adding an additional 1/4 inch to the A and C dimensions for all cut-outs.
Ensure the wall opening dimensions meet the minimum requirements of 16-1/4 inches in height and 42-1/4 inches in width.
Connect the AH12E07D2B electric heater to a 230/208 volt line cord.
Refer to the provided specifications to determine the appropriate electrical settings for the heater, considering the wattage, BTU, amps, and circuit requirements.
Install a 15 amp time-delay fuse or breaker as the recommended protective device.

Please refer to the complete user manual for additional information and safety guidelines.

AH12E07D2B
Hotpoint® PTAC with Electric Heat 15 amps, 230/208 Volt

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

ELECTRICAL WIRING

All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations.
NOTE: Aluminum wiring may pose special problems – consult a qualified electrician.

GRILLE OPTIONS

ELECTRICAL CONNECTION

230/208 volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
Power cord is permanently attached on all Hotpoint chassis.

WALL CASE DIMENSIONS

RAB80 WALL SLEEVE
Heavy-gauge galvanized steel, with insulation, for quick self-assembly.
A – 42”, B – 13-3/4”, C – 16”

MAXIMUM CORD EXTENSION

WALL OPENING DIMENSIONS
Add 1/4” to A and C dimensions for all cut-outs.
RAB80 16-1/4” Min. H x 42-1/4” Min. W

7,400 / 7,300 cooling BTU
13.1 EER
R32 Refrigerant – Environmental friendly, low GWP (Global Warming Potential)
3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
Auto Power Recovery – In case of power failures, units automatically resume their operation when power restores, reducing maintenance calls
Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
Backed by an Industry Leader – With a long history of creating durable products at an affordable price,
Hotpoint is your trusted PTAC brand

Hotpoint-AH12E07D2B-PTAC-with-Electric-Heat-3

PRELIMINARY SPECIFICATIONS – SUBJECT TO CHANGE

| Hotpoint AH12E07D2B PTAC with Electric Heat [pdf] Instruction Manual
AH12E07D2B PTAC with Electric Heat, AH12E07D2B, PTAC with Electric Heat, Electric Heat, Heat
---|---