SALAMANDER DESIGNS EZ-Touch Series Manual Lift Wall Mounts Instruction Manual

June 12, 2024
SALAMANDER DESIGNS

SALAMANDER DESIGNS EZ-Touch Series Manual Lift Wall Mounts

MOODLE

EZ1/ML145
Consists of:
EZ1/MB16/152 Mount Body
EZ1/MA1 VESA Bracket

Displays up to 79-140 lbs (36-64 kg)
VESA Mounting: 200 x 200 – 800 x 670

SALAMANDER DESIGNS EZ-Touch Series Manual Lift Wall
Mounts

EZ1/ML209
Consists of:
EZ1/MB16/209 Mount Body
EZ1/MA1 VESA Bracket

Displays up to 134-197 lbs (61-90 kg)
VESA Mounting: 200 x 200 – 800 x 670

SALAMANDER DESIGNS EZ-Touch Series Manual Lift Wall
Mounts

EZ1/ML095
Consists of:
EZ1/MB16/095 Mount Body
EZ1/MA5 VESA Bracket

Displays up to 41-85 lbs (18-38 kg)
VESA Mounting: 200 x 100 – 800 x 440

PARTS

– EZ1/ML145 / EZ1/ML209 / EZ1/ML095

Parts
Parts

How to use this manual

  1. Read manual carefully before you install the mount
  2. Carry out the actions fully and in the given sequence
  3. The mount guarantee is voided if the product is not correctly installed or modified in any way

Warning symbols used

Warning symbols used

A Sharp edges
B Wear glove
C Physical load
D Two people required
E Entanglement hazard
F Warning: Can cause personal injury or equipment damage

Intended use

The EZ-Touch Mount is a system that compensates the mass of vertically moving displays to ease vertical movement of the display

General warning

The display may only be attached to or removed from the EZ-Touch when the
EZ-Touch is in closed position. The EZ-Touch is under strong spring force. Only operate the EZ-Touch with an adequately balanced display attached to the display frame.
Do not remove any parts of the EZ-Touch. Only the finishing cover can be removed.

Mounting fasteners

Mounting fasteners are not included with the product. Obtain advice from a specialist.

Setting the springs

Adjust only the outer springs:

  • Adjust the height of the outer springs equally
  • Make sure that the height of the display is balanced
  • Increase the spring tension as much as possible
  • Make sure that the display does not move up

Never adjust the inner springs

Disposal of the EZ-Touch

Springs should be unattached before disposal of the EZ-Touch. Sort the EZ- Touch, the accessories and the packaging for the environmentally friendly recycling.

Installation of EZ1/MB16/152 Mount Body Prepare Mounting Site

The EZ-Touch was designed to be installed on a 16” on center 2” x 4” wood stud, or metal studs, using high-quality hollow wall anchor installed in the center of the stud or a solid concrete wall.

WARNING: INSTALLING THE MOUNT IN UNDERRATED OR DAMAGED CONCRETE CAN LEAD TO SERIOUS INJURY OR DAMAGE TO PRODUCT! When installing into concrete only install the mount in a solid concrete wall made of 2500 PSI (17.3 MPa) or stronger concrete. Never install the mount into cracked, chipped or flaking concrete.

WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make sure the structure to which the EZ-Touch is being installed is capable of supporting three times the combined weight of the EZ-Touch and all attached equipment is not to exceed the following weight capacities:

EZ1/MB16/152: 79-140lbs (36-64kg)
EZ1/MB16/209: 134-197lbs (61-90kg)
EZ1/MB16/095: 41-85lbs (18-38kg)

Mounting EZ-Touch Mount Body to Wall

Unpack the EZ-Touch and remove the plastic cover and two foam blocks.

Mounting EZ-Touch Mount Body to Wall

Locating your mount

WOOD CONSTRUCTION:
locate two framing studs (minimum of 16” (405 mm) apart) at the desired location using a stud finder device.

MASONRY: a minimum width of 16” (405 mm) is required between fasteners.

Determine mounting height

See below for recommended mounting height for 55” Display. Other displays can be calculated by adding half the height difference to the top and half the height difference to the bottom of the example shown

Determine mounting height

Mounting bracket level to wall

Unpack the EZ-Touch Take the wall bracket out (A) of the box. Note the slotted/slanted holes for level wall mounting.

Make sure screws are unlocked

Determine mounting height

Touch the mount onto bracket

Determine mounting height

Lock mount with screws

Level vertically with feet at the bottom

Level vertically with feet at the bottom

Insert plastic cover

Attach brackets to mount and display

Attach brackets to mount and display
Attach brackets to mount and display

Warning
Must use M8 x 12mm screws in D-Bag.

Hang display onto horizontal bracket and level

Hang display onto horizontal bracket and level

Lock display with safety lock screws from the bottom

Set balance

Balancing: Springs are always fully tightened for safety. Use a drill driver and 1/2” (13 mm) socket, rotate counter clockwise (loosen) evenly. Do three seconds left and three seconds right until the mount is evenly balanced to support display weightlessly.

Set balance

It may be necessary to tighten if balanced point is exceeded.

SALAMANDER WARRANTY

LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS

Salamander warrants against manufacturing defects for two (2) years from the date of purchase. Salamander will repair or replace, at our option, any product defective in materials or craftsmanship. Batteries are not covered by the warranty.

Customers Support

Full warranty including limitations and warranty claim information may be found at www.salamandercommercial.com

Subject to printing errors and technical amendments.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals