Ai-Thinker Ai-M61EVB-S2 Open Source Hardware WiFi6 Multi-Functional Development Board User Manual
- June 12, 2024
- Ai-Thinker
Table of Contents
Ai-Thinker Ai-M61EVB-S2 Open Source Hardware WiFi6 Multi-Functional
Development Board
Product Information
| Version | Date | Formulation/Revision | Author | Approved by |
|---|---|---|---|---|
| V1.0 | 2023.06.15 | First Edition | Zekai Qian | – |
Product Usage Instructions
Flashing preparation
-
Hardware preparation:
Hardware list:- Ai-M61EVB-S2 board
- USB to TTL module
- DuPont Line (several)
-
Hardware Wiring Instruction:
| Hardware | Ai-M61EVB-S2 | USB to TTL module |
|---|---|---|
| QTY | 1 | 1 |
| Wiring | 3V3 GND RXD TXD | USB TTL 3V3 GND TXD RXD |
Software preparation:
- Flash software, prepare firmware:
- The software compression package is provided. After decompression, the directory structure is as follows:
- The software version used in this fixed frequency test is 1.8.3. The firmware is provided.
Firmware burning:
- To burn the firmware:
- Run BLDevCube.exe
- Select BL616/618 in Chip Type
- Click Finish
- Enter the programming interface
- Flashing steps:
- Connect the TTL connected to the module to the computer.
- After confirming the power on, set the module to the burning mode.
- Specific operation process:
- Long press the S2 button (BURN) without releasing it.
- Press the S1 button (RST).
- Release the S2 button (BURN).
- Select the COM port number connected to the chip.
- Select 921600 for Uart Rate.
- Click the Create & Download button to start downloading the firmware.
- When ALL Success is displayed, it means that the firmware download is complete.
AiPi-Eyes-S2 function test:
-
Hardware preparation:
Hardware list:- AiPi-Eyes-S2
- Type-C cable
- GC9307N, 3.5inch SPI interface capacitive touch screen
- Speaker
Connect the screen, speaker, and Type-C cable to the board.
-
Power-on test:
Power on the module using the Type-C interface with a 5V power supply. After power on, the startup screen will be displayed. -
Configure WiFi:
- Swipe down from the top of the screen and click Network to enter the WiFi configuration interface.
- Enter the WiFi name and password, and click Connect.
- The status will display the connection status (OK means success, Fail means failure).
- After successfully connecting to WiFi, the time will be updated to Beijing time synchronously. Note: Restarting the module will require re-timing, and WiFi needs to be re-entered.
-
Button function test:
Swipe down from the top of the screen and there will be three buttons: Network, Restore, and Info. The corresponding functions are as follows:- Network: Configure network
- Restore: Restart
- Info: Display system information
Flashing preparation
Hardware preparation
Hardware list：
| Hardware | QTY |
|---|---|
| Ai-M61EVB-S2 | 1 |
| USB to TTL module | 1 |
| DuPont Line | several |
Wiring Instruction：
| Ai-M61EVB-S2 | USB 转 TTL 模块 |
|---|---|
| 3V3 | 3V3 |
| GND | GND |
| RXD | TXD |
| TXD | RXD |
Board wiring diagram：
Board connect TTL：
Software preparation
- Flash software, prepare firmware
- The software compression package is as follows:
* The directory after software decompression is as follows:
* The software version used in this fixed frequency test is 1.8.3
* The firmware is as follows:
- Firmware burning
Run “BLDevCube.exe”, select BL616/618 in Chip Type, click Finish, and enter the programming interface as follows.
Flashing steps:
- Connect the TTL connected to the module to the computer. After confirming the power on, you need to set the module to the burning mode. The specific operation process is Long press the S2 button (BURN) without releasing it, press the S1 button (RST), and then release the S2 button (BURN)
- COM Port： Select the COM port number connected to the chip (if there is no COM port displayed, click the “Refresh” button to refresh the COM port option), select 921600 for Uart Rate, click the “Create & Download” button to start downloading the firmware, when “ALL Success” is displayed, It means that the firmware download is complete.
- The flashing success interface is as follows:
AIPi-Eyes-S2 function test
- Hardware preparation
**** Hardware| QTY
---|---
AIPi-Eyes-S2| 1
Type-C cable| 1
GC9307N,
3.5inch SPI interface capacitive touch screen
| 1
speaker| 1
- Connect the screen, speaker, Type-C cable to the board.
- Power-on test
- Power on the Type-C interface that supplies power to the module, and the module uses 5V for power supply. After power on, the startup screen is as follows:
* The main interface is as follows:
-
Configure WiFi
-
Swipe down from the top of the screen with your finger, you can see three buttons, click Network to enter the WiFi configuration interface.
-
Enter the WiFi name and password, and click Connect.
-
After entering the correct WiFi name and password, the status will display the status of the connection, OK means success, and Fail means failure.
-
* After successfully connecting to WiFi, the time will be updated to Beijing time synchronously. Note: the time required to restart the module will be re-timed, and WiFi needs to be re-entered.-
Button function test
-
Two buttons are provided in the main interface, which are switch and button. At present, the buttons have no redundant functions. Only the speaker responds to the state of the button after being pressed, and the voice broadcasts “turn on the switch” and “turn off the switch”.
-
When the sleep button in the lower right corner is pressed, the screen will enter sleep mode. The screen will automatically enter sleep mode if there is no touch for 30s.
-
In sleep mode, the brightness of the screen is low and only the time is displayed.
-
Swipe down from the top of the screen with your finger and there will be three buttons, namely Network, Restore, and Info. The corresponding functions are, configure network, restart, and system information. After clicking info, the following information appears.
-
Contact us
- Official website：https://www.ai-thinker.com
- Development DOCS：https://docs.ai-thinker.com
- Official Forums：http://bbs.ai-thinker.com
- Purchase sample：https://ai-thinker.en.alibaba.com/
- Business cooperation：overseas@aithinker.com
- Support：support@aithinker.com
- Office address： Room 410, Building C, Huafeng Intelligence Innovation Port, Gushu, Xixiang, Baoan District, Shenzhen 518126, China
- Tel ：0755-29162996
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>