Blackview Tab 70 WiFi Tablet User Manual

Blackview Tab 70 WiFi Tablet

Product Information:

Product Name: Tab 70 WiFi Tablet
Language: English

How to insert the TF card:

1. Locate the TF card slot on the tablet.
2. Gently insert the TF card into the slot, making sure it is properly aligned.
3. Push the TF card in until it clicks into place.

Safety Instructions:

• The tablet should be kept at least 15 cm away from any medical implant or rhythm adjuster. Do not put the device in your coat pocket.
• Avoid exposing the device and other batteries to high temperatures or heat-generating equipment such as sunlight, heaters, microwave ovens, ovens, or water heaters. Overheating can cause an explosion.
• When charging is complete or not charging, disconnect the charger from the device and unplug it from the power outlet.
• If the tablet has a non-removable battery, do not attempt to replace it yourself to avoid damaging the battery or device.
• Use only approved and compatible power sources to prevent hazards.
• Do not disassemble or reset the battery, insert other objects, or immerse the device in water or other liquids to avoid battery leakage.
• Avoid dropping, crushing, scratching, or puncturing the battery to prevent excessive external pressure, which can lead to internal short-circuits and overheating. The company is not responsible for accidents caused by non-standard charging equipment.

Maintenance:

• Follow the instructions in the manual to open the tablet and disassemble the accessories. Do not use other methods.

• Avoid falling, knocking, or shaking the tablet as it can cause the screen to rupture and damage the internal circuit board and delicate structure.

• Do not use chemical solvents or detergents to clean the tablet.
  Instead, wipe the tablet case with a soft cotton cloth dampened with water or mild soap.

• Clean the lens and display with a clean, dry, soft cloth (e.g., camera lens).

Troubleshooting:

If you encounter an abnormal image or a crash during use, follow these steps:

• For tablets without removable batteries: Press and hold the power button for more than 12 seconds to force a restart. This can solve general bugs.
• For tablets with removable batteries: Remove the battery, then reinsert it and restart the tablet to solve the bug.

Note: For more information on CE compliance, visit http://www.blackview.hk/ce/

Charger/Type-C: Connect the charger to the tablet using the Type-C port.

Power On/Off:

To power on the tablet, press and hold the power button for 3-5 seconds. To power off the tablet, press and hold the power button until the power options appear, then select “Power off”.

SAR (Specific Absorption Rate): The SAR value of this tablet is 2.0W/kg. It complies with the SAR standards set by 21288-2007.

OVERVIEW

How to insert the TF card

How to boot
Non-removable battery
Press the power button for 3-5 seconds to boot

Language switching settings

• Main menu -settings-system setting language and input method
• Language and input method—language–language adding
• Select the language you need, the system will automatically jump back to the language interface
• Select the icon after the language bar and drag it to the first one.

SAR

• The maximum electromagnetic radiation absorption ratio (SAR) of this product is <2.0W/kg.
• In line with the requirements of the national standard GB 21288-2007.

Safety- In order to ensure safely using the product, you must strictly abide by the following rules

• The pad should be at least 15 cm away from any medical implant or rhythm adjuster and never put the device in your coat pocket.

• Do not expose the device and other batteries together with the high temperatures or heat-generating equipment such as sunlight, heaters, microwave ovens, ovens or water heaters. Overheating of the battery can cause an explosion.

• When charging is complete or not charging, disconnect the charger from the device and unplug the charger from the power outlet.

• Ifthe device is equipped with a non-removable battery, do not replace the battery yourself to avoid damaging the battery or device.

• Use of an unapproved or incompatible power source, charger or battery may cause fire, explosion or other hazards.

• Do not disassemble or reset the battery, insert other objects, immerse in water or other liquids to avoid battery leakage, overheating, fire or explosion.

• Do not drop, crush, scratch or puncture the battery to avoid subjecting the battery to excessive external pressure, resulting in internal short-circuit and overheating of the battery.
  The company does not bear the responsibility for accidents caused by non- standard related charging equipment.

• If you want to read the full CE accompliance, please check this link: http://www.blackview.hk/ce/

Maintenance

• Thoroughly understand the maintenance of this pad to use the pad more safely and effectively, and extend the service life of the pad as much as possible.

• Please follow the instructions in the manual to open the pad, disassemble the accessories, and do not try other methods.

• Please avoid falling, knocking or shaking your pad Rough handling of the pad can cause the screen to rupture, damaging the internal circuit board and the delicate structure.

• Do not use chemical solvents or detergents to clean your pad. Wpe the pad case with a soft cotton cloth dampened with water or a mild soap.

• Clean the lens with a clean, dry, soft cloth.
  (Example: camera lens) and display

• If you encounter an abnormal image such as a crash during use, the processing method is as follows: For a pad that cannot remove the battery, please press and hold the power button for more than 12 seconds, the pad will be iorced to restart (unlock the pad when restarting)
  It can solve the general bug; for the pad that can remove the battery, please remove the battery, then insert the battery and restart to solve the bug.

• When the charger is not in use, please unplug it from the power outlet. Do not connect the battery that has been fully charged to the charger for a long time, as overcharging will shorten the battery life.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Warning
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Th e device for operation in the band 5150–5250MHz is only for indoor use.

RF Exposure Information and Statement
The SAR limit of USA/Canada (FCC/IC) is 1.6 W/kg averaged over one gram of tissue. Device types:
Tab 70 WiFi (FCC ID: 2A7DX-TAB70WF, IC: 25768-TAB70WF) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use the body is 0.168W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Follow Blackview communtiy, a place where you can share and discuss with Blackview user keep posted with most up-to-day news

http://www.blackview.hk

References

• CE | Blackview

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>