ASUS VS278 Series LCD Monitor User Guide
- June 13, 2024
- Asus
Table of Contents
- Notices
- Safety information
- Care & Cleaning
- Conventions used in this guide
- Where to find more information
- Takeback Services
- Product Introduction
- Welcome!
- Package contents
- Monitor introduction
- Back view
- QuickFit Function
- Assembling the monitor arm/base
- Adjusting the monitor
- Detaching the arm/base (for VESA wall mount)
- Connecting the cables
- Turning on the monitor
- OSD (On-Screen Display) menu
- OSD function introduction
- Specifications summary
- Troubleshooting (FAQ)
- Supported operating modes
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ASUS VS278 Series LCD Monitor
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference – Causing Equipment Regulations.
Cet appareil numérique de la classed B respected touts les exigence’s du
Regalement sur le materiel broiler du Canada.
Safety information
- Before setting up the monitor, carefully read all the documentation that came with the package.
- To prevent fire or shock hazard, never expose the monitor to rain or moisture.
- Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury.
- If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
- Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
- Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided.
- The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.
- Use the appropriate power plug which complies with your local power standard.
- Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
- Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface.
- Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges.
- Never push objects or spill liquid of any kind into the slots on the monitor cabinet.
- To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC.
- If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.
- Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the ear-/headphones output voltage and therefore the sound pressure level.
This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Please check local regulations for disposal of electronic products.
Care & Cleaning
- Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.
- Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner.
- Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the monitor. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
- The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears.
- You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
- When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours.
- When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Where to find more information
Refer to the following sources for additional information and for product and software updates.
1. ASUS websites
The ASUS websites worldwide provide updated information on ASUS hardware and
software products. Refer to http://www.asus.com
2. Optional documentation
Your product package may include optional documentation that may have been
added by your dealer. These documents are not part of the standard package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions
for our customers to be able to responsibly recycle our products, batteries
and other components as well as the packaging materials.
Please go to
http://csr.asus.com/english/Takeback.htm
for detail recycling information in different region.
Product Introduction
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing
experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
Package contents
Check your package for the following items:
- LCD monitor
- Monitor base
- Quick start guide
- Warranty card
- Power cord
- VGA cable
- Audio cable
- HDMI-DVI cable
If any of the above items is damaged or missing, contact your retailer immediately.
Monitor introduction
Front view
-
button:
• Activates the QuickFit function.(Please refer to 1.3.3 QuickFit Function). -
button:
• Selects a desired preset mode.
• Exits the OSD menu or goes back to the previous menu when the OSD menu is active.
• Automatically adjusts the image to its optimized position, clock, and phase by pressing this button for 2-4 seconds (for VGA mode only). -
button:
• Decreases values or moves your selection left/down.
• Volume hotkey -
MENU button:
• Turns on the OSD menu. Enacts the selected OSD menu item. -
button:
• Increases values or moves your selection right/up.
• Brightness hotkey -
button:
• Selects an available input source.
Press (Input Select button) to display HDMI/DisplayPort signals after you\ connect HDMI/DisplayPort cable with the monitor. -
Power button/power indicator
• Turns the monitor on/off.
• The color definition of the power indicator is as the below table.
Status | Description |
---|---|
Blue | ON |
Amber | Standby mode |
OFF | OFF |
Back view
Rear connectors
- AC-IN port. This port connects the power cord.
- Power Switch. To switch the display on and off.
- DisplayPort. This port is for connection for a DisplayPort compatible device.
- HDMI port. This port is for connection with an HDMI compatible device.
- VGA port. This 15-pin port is for PC VGA connection.
- Audio-in port. This port connects PC audio source by the bundled audio cable.
- Earphone jack. This port is only available when an HDMI/DisplayPort cable is connected.
QuickFit Function
The QuickFit function allows users have a preview of the document or photo
layout directly on screen without printing test copies.
To activate QuickFit, press the QuickFit hotkey, and then press the MENU key
to switch between different pattern sizes.
When QuickFit is activated, press the control buttons on the front panel to make adjustments. The QuickFit OSD displayed in the lower right corner of the screen will guide users to make selections.
The QuickFit OSD shown on the screen is not accessible by tapping on it.
Assembling the monitor arm/base
To assemble the monitor base:
- Have the front of the monitor face down on a table.
- Attach the base into the arm, making sure the tab on the arm fits into the groove on the base.
- Fix the base to the arm by fastening the bundled screw.
We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.
Adjusting the monitor
For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you.
- Hold the stand to prevent the monitor from falling when you change its angle.
- The recommended adjusting angle is +20˚ to -5˚.
It is normal that the monitor slightly shakes while you adjust the viewing angle.
Detaching the arm/base (for VESA wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
- Have the front of the monitor face down on a table.
- Remove the rubbers in the four screw holes. (Figure 1)
- Remove the base (Figure 2).
- Pry the rear hinge cover (Figure 3).
- Use a screwdriver to remove the four screws on the hinge (Figure 4), then remove the hinge.
|
---|---
Figure 1| Figure 2
|
Figure 3| Figure 4
We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.
Connecting the cables
Connect the cables as the following instructions:
-
To connect the power cord: connect one end of the power cord securely to the monitor’s AC input, the other end to a power outlet.
-
To connect the VGA/HDMI/DisplayPort cable:
a. Plug one end of the VGA/HDMI/DisplayPort cable to the monitor’s VGA/ HDMI/DisplayPort port.
b. Connect the other end of the VGA/HDMI/DisplayPort cable to your computer’s VGA/HDMI/DisplayPort port.
c. Tighten the two screws to secure the VGA connector. -
To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer’s audio-out port. -
To use the earphone (only when an HDMI/DisplayPort cable is connected): connect the end with plug type to the monitor’s earphone jack.
When these cables are connected, you can choose the desired signal from the Input Select item in the OSD menu.
Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The power indicator lights up in blue to show that the monitor is ON.
OSD (On-Screen Display) menu
How to reconfigure
-
Press the MENU button to activate the OSD menu.
-
Press and to navigate through the functions.
Highlight the desired function and press the MENU button to activate it. If the function selected has a sub-menu, press and again to navigate through the sub-menu functions. Highlight the desired sub-menu function and press the MENU button to activate it. -
Press and to change the settings of the selected function.
-
To exit and save the OSD menu, press the button repeatedly until the OSD menu disappears. To adjust other functions, repeat steps 1-3.
OSD function introduction
Splendid
This function contains six sub functions you can select for your preference.
Each mode has the Reset selection allowing you to maintain your setting or
return to the preset mode.
- Scenery Mode : best choice for scenery photo display with SPLENDID™ Video Enhancement.
- Standard Mode : best choice for document editing with SPLENDID™ Video Enhancement.
- Theater Mode : best choice for movies with SPLENDID™ Video Enhancement.
- Game Mode : best choice for games playing with SPLENDID™ Video Enhancement.
- Night View Mode : best choice for dark-scene games or movies with SPLENDID™ Video Enhancement.
- sRGB : best choice for viewing photos and graphics from PCs.
In the Standard Mode, the ASCR, Saturation and Sharpness functions are not user-configurable.
Color
You can adjust Brightness, Contrast, Saturation, Color Temp., Skin Tone, and
Smart View from this menu.
- Brightness: the adjusting range is from 0 to 100. is a hotkey to activate this function.
- Contrast: the adjusting range is from 0 to 100 .
- Saturation: the adjusting range is from 0 to 100.
- Color Temp.: contains four modes including Cool, Normal, Warm, and User Mode.
- Skin Tone: contains three color modes including Reddish, Natural, and Yellowish.
- Smart View: provides better display quality under big viewing angle.
In the User mode, colors of R (Red), G (Green), and B (Blue) are user configurable; the adjusting range is from 0 100.
Image
You can adjust Sharpness, Trace Free, Aspect Control, ASCR, Position (VGA
only), and Focus (VGA only) from this menu.
- Sharpness: the adjusting range is from 0 to 100.
- Trace Free: adjusts the response time of the monitor.
- Aspect Control: adjusts the aspect ratio to full, 4:3, 1:1 or Over Scan.
4:3 is only available when input source is in 4:3 format. Over Scan is only available for the HDMI input source.
- ASCR: turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
- Position: adjusts the horizontal position (H-Position) and the vertical position (V-Position) of the image. The adjusting range is from 0 to 100.
- Focus: reduces Horizonal-line noise and Vertical-line noise of the image by adjusting (Phase) and (Clock) separately. The adjusting range is from 0 to 100.
- Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows horizontal disturbances.
- Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image is not proportional.
Input Select
In this function, you can select your desired input source.
System Setup
Allows you to adjust the system.
-
Splendid Demo Mode:
splits the screen into two for Splendid modes comparison. -
Volume: the adjusting range is from 0 to 100.
-
ECO Mode: reduces power consumption.
-
OSD Setup:
-
Adjusts the horizontal position (H-Position)/the vertical position (V-Position) of the OSD from 0 to 100.
-
Adjusts the OSD timeout from 10 to 120 seconds.
-
Enables or disables the DDC/CI function.
-
Adjusts the OSD background from opaque to transparent.
- Information: shows the monitor information.
- Language: there are 21 languages for your selection, including English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesia, Persian.
- All Reset: “Yes” allows you to restore the default settings.
Specifications summary
Panel Type | TFT LCD |
---|---|
Panel size | 27”W (16:9, 68.58 cm) wide screen |
Max. Resolution | 1920 x 1080 |
Pixel pitch | 0.3114 mm |
Brightness (Typ.) | 300 cd/m2 |
Contrast Ratio (Typ.) | 1000:1 |
Contrast Ratio (Max.) | 80,000,000:1 (with ASCR on) |
Viewing angle(H/V) CR >10 | 170˚/160˚ |
Display colors | 16.7 M |
Response time | 1 ms |
SPLENDID™ Video Enhancement | Yes |
SPLENDID™ selection | 6 video preset modes (by hotkey) |
Auto adjustment | Yes (by hotkey) |
Color temperature selection | 4 color temperatures |
Skin-Tone selection | 3 skin-tones |
Digital input | HDMI v1.4 x 2, DisplayPort v1.1a (VS278Q) |
Analog input | D-Sub |
Audio-in port | 3.5 mm Mini-jack |
Earphone jack | Yes (VS278Q/VS278H) |
Colors | Black |
Speaker (Built-in) | 2 W x 2 Stereo, RMS |
Power LED | Blue (On)/Amber (Standby) |
Tilt | +20˚~ -5˚ |
VESA wall mount | 100 x 100 mm |
Kensington lock | Yes |
Voltage rating | AC: 100~240V |
Power consumption | Power On: < 45 W, Standby: < 0.5 W, Power Off: Hard |
Switch 0 W
Temperature (Operating)| 0˚C~40˚C
Temperature (Non-operating)| -20˚C~+60˚C
Dimensions (W x H x D)| 646.86 mm x 470.11 mm x 225 mm (machine)
725 mm x 541 mm x 175 mm (package)
Weight (Esti.)| 5.080 kg (Net); 7.228 kg (Gross)
Multi- languages| 21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech, Croatia, Polish, Romanian,
Hungarian,
Turkey, Simplified Chinese, Traditional Chinese,
Japanese, Korean, Thai, Indonesia, Persian)
Accessories| VGA cable, HDMI-DVI cable, audio cable, power cord, Quick
start guide, warranty card
Regulation approvals| CB, CE, Gost-R, CCC, UL/cUL, FCC, C-Tick,
BSMI, VCCI, RoHS, WEEE, J-MOSS, ErP, PSE,
KC, Windows 7 WHQL
Troubleshooting (FAQ)
Problem | Possible Solution |
---|---|
Power | LED is not ON |
- Press the button to check if the monitor is in the ON mode.
- Check if the power cord is properly connected to the monitor and the power outlet.
The power LED lights amber and there is no screen image|
- Check if the monitor and the computer are in the ON mode.
- Make sure the signal cable is properly connected the monitor and the computer.
- Inspect the signal cable and make sure none of the pins are bent.
- Connect the computer with another available monitor to check if the computer
is properly working.
Screen image is too light or dark|
- Adjust the Contrast and Brightness settings via OSD.
Screen image is not centered or sized properly|
- Press the button for 2-4 seconds to automatically adjust the image (for VGA mode only).
- Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is present in the image|
- Make sure the signal cable is properly connected to the monitor and the computer.
- Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does not look white)|
- Inspect the signal cable and make sure that none of the pins are bent.
- Perform All Reset via OSD.
- Adjust the R/G/B color settings or select the Color Temperature via OSD.
Screen image is blurry or fuzzy|
- Press the button for 2-4 seconds to automatically adjust the image (for VGA mode only).
- Adjust the Phase and Clock settings via OSD.
No sound or sound is low|
- Ensure that the HDMI cable is properly connected to the monitor and the computer.
- Adjust the volume settings of both your monitor and HDMI device.
- Ensure that the computer sound card
driver is properly installed and activated.
Supported operating modes
Resolution Frequency| Horizontal Frequency (KHz)|
Vertical Frequency (Hz)| Pixel (MHz)
---|---|---|---
640×480| 31.5| 60| 25.18
640×480| 35.0| 67| 30.24
640×480| 37.9| 72| 31.50
640×480| 37.5| 75| 31.50
720×400| 31.5| 70| 28.32
800×600| 35.16| 56| 36.00
800×600| 37.9| 60| 40.00
800×600| 48.1| 72| 66.75
800×600| 46.9| 75| 49.50
832×624| 49.7| 75| 57.28
1024×768| 48.4| 60| 65.00
1024×768| 56.5| 70| 75.00
1024×768| 60.0| 75| 78.50
1152×864| 67.5| 75| 108.00
1280×720| 45| 60| 75.25
1280×768| 47.78| 60| 79.50
1280×800| 49.7| 60| 83.50
1280×960| 60.0| 60| 108.00
1280×1024| 63.4| 60| 108.00
1280×1024| 79.97| 75| 135.00
1360×768| 47.71| 60| 85.50
1366×768| 47.71| 60| 85.50
1440×900| 55.94| 60| 106.50
1600×1200| 75.0| 60| 162.00
1680×1050| 65.3| 60| 146.25
1920×1080
(Primary)
| 67.5| 60| 148.50
References
- Global Take Back Service | Resource Regeneration | Circular Economy | ASUS ESG website, ASUS ESG goal
- How.To – For Those Who Love to Learn
- ASUS Global
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>