Godox TP2R Knowled Pixel Wireless RGB Tube Light Instruction Manual

Godox TP2R Knowled Pixel Wireless RGB Tube Light

Safety Instructions and Attentions

First of all, as the most basic principle: This product is a professional lighting set equipment and should be used by professional lighting engineers or under the guidance of professionals. Basic safety attentions must always be followed during use, as follows:

1. Before use, please read and understand these instructions and attentions.
2. Professional lighting is prohibited for children. When children are near, parents or accompanying persons must supervise closely to prevent children from personal injury due to collision with lamps or private use of lamps.
3. This lighting product is not ordinary lighting product and cannot be used for general lighting. Anyone who has suffered eye damage or has sensitive eyes should avoid using this product.
4. When the lamp is on, it must be used with care. Do not touch high-temperature parts, such as LED lamp beads, to avoid burns.
5. When the lamp is on, it is forbidden to look directly at the lamp beads under any circumstances. Strong light should be used under the guidance of professional lighting engineers. Avoid prolonged exposure to strong light under any circumstances. If eye discomfort, please turn off the lamp in time, suspend use, and see a doctor immediately.
6. If the lamp bead is damaged or deformed by heat, stop using this equipment, and contact the manufacturer, service agent or qualified maintenance personnel to replace the lamp bead in time to avoid accidents.
7. This product is only suitable for use in -10°C to 40°C operating environment and normal humidity environment.
8. Do not use damaged equipment or accessories, and wait for professional maintenance personnel to check and repair to confirm being normal before use.
9. During using, if the casing of this product is broken due to being dropped, squeezed or subjected to strong impact, please do not use it, so as to avoid electric shock injury due to contact with internal electronic components.
10. If an extension cord is required, please use an extension cord with a current rating greater than or equal to that of the equipment. If an extension cord is rated less than the equipment, overheating may result.
11. Some products have long power cords, please place the power cords properly and keep them in a safe place. Avoid contacting the power cord with overheating surfaces, avoid improper placement that could cause pulling damage, or trip on-site personnel. Please use the certified power cord from the original manufacturer. If the product is damaged by using a non-certified power cord, it will not be repaired by our factory.
12. Be sure to unplug equipment from the power outlet before cleaning and repairing. When not in use, do not pull the power cord to unplug the equipment. For normal power-off, please hold both ends of the plug of the equipment with your hands and pull the plug out of power outlet This equipment needs to be connected to a grounded outlet.
13. Do not disassemble the product without permission. If the product fails, it must be checked and repaired by authorized maintenance personnel.
14. Before storing, make sure that the equipment has cooled down completely. For storage, unplug the power cord from the equipment. The equipment should be placed in the carrying case or in a ventilated dry place.
15. Do not place equipment near flammable and volatile solvents such as alcohol and gasoline.
16. Do not use accessories that are not recommended by our factory to avoid fire, electric shock or personal injury.
17. When cleaning, do not wipe it with a damp cloth, please use a dry cloth or a soft cloth to wipe the dirt of the equipment.
18. Please take off the protective cover before using.
19. This product complies with ROHS, CE and FCC certification, please refer to the relevant national standards for use and operation.
20. The safety instructions are formulated according to the strict testing of the factory, and the design and specifications of the equipment are subject to change without prior notice. For latest product information, please check the GODOX website and view latest electronic instruction.
21. Some products have built-in lithium batteries. Please use specified chargers, and use them within a proper range of the specified voltage and temperature according to the correct operating instructions.
22. Some products are battery powered. Do not use any batteries, power sources or accessories not specified in the instructions for such products. Keep batteries and other accessories out of the reach of children and infants. In the instance that a child or infant swallows a battery or accessory, immediate emergency medical attention is required. If the battery leaks, becomes discolored, deformed, emits smoke, or emits an abnormal odor, remove it immediately. Be careful during removal to avoid burns. Continued use could result in fire, electric shock, or burns. Do not use any deformed or modified batteries. Do not disassemble or modify this product or battery. Do not heat or solder the battery. Keep the battery away from fire or water. Do not incorrectly insert the positive and negative ends of batteries, or mix old and new batteries or batteries of different types together.
23. One-year warranty period, accessories such as consumable batteries, adapters, power cords, etc. are not covered by this warranty.
24. If it is found that the equipment is repaired without authorization, the one-year warranty period will be cancelled and relevant fees will be charged for maintenance.
25. Machine failures caused by non-standard operation are not covered by the warranty.
    keep these instructions!

Foreword

Thank you for purchasing!
TP2R, TP4R and TP8R are the latest RGBWW tube lights feature various powerful characteristics such as convenient usage, waterproof grade of IP65, built-in lithium battery, 3/8″ screw holes on both sides, five effect modes (CCT mode, HSI mode, GEL mode and FX mode), support Bluetooth/ DMX512/wireless CRMX/RDM control. This tube light is suitable for professional film and television shooting activities, studio shooting, etc.

Main Features

• Four dimming curves: linear, S-curve, exponential and logarithmic.

• Wide CCT range freely adjustable from 2000K to 1 OOOOK.

• TP2R has built-in 43.2Wh lithium battery which provides working time about l 20min in 100%brightness.

• TP4R has built-in 86.4Wh lithium battery which provides working time about l 20min in 100% brightness.

• TP8R has built-in l 72.8Wh lithium battery which provides working time about l 40min in 100% brightness.

• TP2R: 16 individually controllable pixels, TP4R: 32 individually controllable pixels, TP8R: 64 individually controllable pixels.

• Super high color rendering index: average CRle96, average TLCle96.
  Multiple smart control methods: DMX 512/wireless CRMX/Bluetooth APP/light body/RDM control.
  Protection grade of IP65 keeps the light from dust and water. 17 FX modes: RGB fade, RGB flow, RGB chase, RGB cycle, party, flash, lightning, cloudy, broken bulb, TY, candle, fire, firework, explosion, welding, cop car, SOS.

• Smart battery level indication gives convenient information.

Warnings

Do not look directly at the tube light, visual impairment may occur.
 Do not look at the LED light with a magnifying glass or other optical instrument that may concentrate light output.
Do not operate this device in a high temperature environment or under direct sunlight, otherwise abnormalities or damages may occur.
 Do not store lights when the battery runs out. Please make sure the light has power before storage.
 If the battery runs out, please charge it immediately.
Do not charge it unattended.
Avoid collisions or falls, which may cause fires or explosions.
 Do not turn on the electricity if the light is damaged, and be careful of electric shock.

Name of Parts

Light Body

1. CRMX Indicator
2. Bluetooth Indicator
3. Battery Level Indicator
4. Display
5. Power Switch Button
6. MOD/MENU Button
7. FN Button
8. – Button
9. + Button
10. OMX Port
11. DC Input Port
12. 3/8″ Screw Hole

Display

When   icon is on the display, it means DC power supply.

When icon is on the display, it means lithium battery power supply.

What’s Inside (TP2R/TP4R/TP8R)

• Light Body*l

• Power Cable*1

• Adapter*1

• Carry Bag*l (TP8R doesn’t include a carry bag)

• Clamp• l (TP2R)
  Clamp•2 (TP4R)
  Clamp’4 (TP8R)

• Instruction Manual* 1

• Steel Rope*2

• Screw Bolt *2

Note: Due to continuous updates and upgrades of the products, there may be differences between the actual products and the pictures. Therefore, the pictures are for reference only, products to prevail in kind.

Separately Sold Accessories

Power Box TP-P600, Multi-tube Light Connector (Two Joints) TP-M2, Two-light Bracket Kit TP-B2, Four-light Bracket Kit TP-B4, Eight-light Bracket Kit TP-B8, Softbox TP-S2, Air Soft Tube TP-S2A, OMX Connector Cable OMX-Cl, Floor Stand TP-FS60

Battery

1. This product has built-in lithium battery. The inner circuit is against overcharge, over-discharge, over current, and short circuit
2. Please use the standard adapter for charging.

Indicators Description

Connect to DMX Controller

Wireless DMX Connection

Wired DMX Connection

Operation Instruction

 Power Switch

Long press the power switch button for 2s to turn on or off the device.
Note: The device will be turned on automatically in DC power supply if the quick start function is turned on (available in menu setting).

Mode Settings

Short press the MOD/MENU button to switch among CCT mode, HSI mode, RGB mode, GEL mode and FX mode.

CCT Mode

Short press the FN button in CCT mode to adjust DIM/CCT/GM, press+ button to increase value while press – button to decrease value.
DIM: 0%-100%
CCT: 2000K-10000K
GM:- 50-+50

HSI Mode

Short press the FN button in HSI mode to adjust H (HUE)/S (saturation)/1 (intensity), press+ button to increase value while press – button to decrease value.
H (HUE): 0°-360°
S (saturation): 0%-100%
I (intensity): 0%-100%

RGB Mode

Short press the FN button in RGB mode to adJust R (red)/G (green)/B (blue)/W (white)/1 (intensity), press+ button to increase value while press – button to decrease value.
R (red): 0-255
G (green): 0-255
B (blue): 0-255
W (white): 0-255
I (intensity): 0%-100%

GEL Mode

Short press the FN button in GEL mode to adjust DIM/GEL/Num/CCT, press+ button to increase value while press – button to decrease value.
DIM: 0%-100%
GEL: L-GEL, R-GEL
L-GELNum: 30
R-GEL Num: 30
CCT: 3200K, 5600K 2.5 FX Mode
GEL 2 □ : □□ oc:i,
DIM- 2%
GEL- R-GEL
► NUM- 65
Short press the+/- button in FX mode to select the desired effect, then short press the FN button to select an effect setting, press+/- button to adjust the setting.Short press the FN button for 2s can return to the previous option
There are 17 effects for choice: RGB fade, RGB flow, RGB chase, RGB cycle, party, flash, lightning, cloudy, broken bulb, TV, candle, fire, firework, explosion, welding, cop car, SOS.

RGB fade

RGB fade effect supports adjustable DIM, speed, color and direction.
DIM: 0%-100%
Speed: 1-100
Color Width: 1-8
Color Num: 1-8 F >< oc:i,
► FX RGB Fade j
DIM: 0% I S eed, 80
Available colors of Cl to CB: 3200K, 5600K, Red, Orange, Yellow, Green, Cyan, Blue, Purple, Magenta DIRL (left)/R (right)
Note: Short press the MOD/MENU button in secondary option can return to the previous menu.
RGB Flow

RGB flow effect supports adjustable DIM, speed,
color and direction.
DIM: 0%-100%
Speed:1-100
Color Width: 1-8
Color Num:2-8
► FX RGB Flow j
DIM: 1% I S eed, 1
Available colors of Cl to CB: 3200K, 5600K, Red, Orange, Yellow, Green, Cyan, Blue, Purple, Magenta
DIR: L {left)/R (right)
Note: Short press the MOD/MENU button in secondary option can return to the previous menu.

RGB Chase

RGB chase effect supports adjustable DIM, speed, color and direction. ► FX : RGB Chase j
DIM: 0%-7 00%
Speed: 7 – 700
Color Width: 7 -8
DIM: 0% I
S eed: 1
Color Num: 2-8
Available colors of Cl to CB: 3200K, 5600K, Red, Orange, Yellow, Green, Cyan, Blue, Purple, Magenta DIR:L (left)/R (right)
Note: Short press the MOD/MENU button in secondary option can return to the previous menu.

RGB Cycle

DIM: 0%-100%
Speed: 7 -7 00
SAT (saturation): 0%-7 00%

Party

DIM :0%-700%
Speed: 7-700
SAT (saturation): 0 %-7 00%

Flash

Trig: Auto, Manual
DIM: 0%-7 00%
Speed: 7 -7 00 (only adjustable in auto mode)
Note: Short press+ button once to trigger flash once in manual mode.

Lightning

Trig: Auto, Manual
DIM: 0%-7 00%
Blinks: Rnd/7-l 0
Freq: Rnd/2-20 (only adjustable in auto mode)
Note: Short press+ button once to trigger lightning once in manual mode.

Cloudy

DIM: 0%-700%
DIM Ratio: 30%-90%
Speed: Rnd/7 -7 00

Broken Bulb

Color: CCT, HSI
CCT: 2000K-7 OOOOK (only adjustable in CCT mode)
HUE: D°-360′ (only adjustable in HSI mode)
DIM: 0%-700%
Speed: Rnd/7 -7 00

TV

Color: CCT, HSI
DIM: 0%-700%
Speed: 1 -700

Candle

DIM: 0%-7 00%
Speed: 7-7 00

Fire

DIM: 0%-7 00%
Speed: 7-7 00

Firework

DIM: 0%-700%
Embers: 7 -7 00
Speed: l-700

Explosion

Note: Short press+ button once to trigger explosion once in manual mode

Trig: Auto, Manual Color CCT, HSI
CCT: 2000K-7 OOOOK (only adjustable in CCTmode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-700%
Embers: 7 -100
Speed: 7 -7 00 (only adjustable in auto mode)

Welding

Color: CCT, HSI
CCT : 2000K-1 OOOOK (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-700%
Speed: l-700

Cop Car

Color: R&B, Red, Blue, B&W, B&Y, Yellow, R&B&W, R&B&Y DIM 0%-700%
MOD: 7-5

sos

Color: CCT, HSI
CCT: 2000K-7 OOOOK (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM : 0%-700%

Setting

Long press the MOD/MENU button to enter Setting, short press the FN button to select DMX/CRMX/Fixture NO./Ordering/Bluetooth/Dimming Curve/Quick Start/Rotate Screen/Preset/Battery/Overheat PROT/Language/Factory Reset/Version (short press FN button twice can return to previous option), short press the+ button to enter the desired setting, after which short press the MOD/MENU button can return to previous setting.

DMX

Short press the FN button to select ADD/Pixels/MOD/Loss/ROM in OMX settings interface, then short press-/+ button to adjust the settings. ROM on: The luminaire ADD and OMX mode are operational via controller.

Note: Please refer to the DMX Practical Table to control the device by OMX, the electronic versions of which
can be downloaded from the official website https://www.godox.com.

CRMX

Short press the – button can turn off CRMX while short press the+ button can turn on CRMX. When the CRMX is turned on, short press the FN button to MOD, then short press the-/+ button to select TX/RX mode.
RX mode: CRMX indicator will be constant on green when linked.
TX mode: Short press the FN button to select Link/Unlink/Power. Short press the+ button to link or unlink. Short press the-/+ button to adjust power. CRMX indicator will be constant on magenta when transmitting OMX data, and blink magenta when unlinked.

Fixture NO

The number of fixture can be adjusted from N0.007 to N0.999 in the fixture NO. interface.

Ordering

Short press the FN button to select Pixels/Order/Length, short press the-/+ button can adjust the desired setting.
Ordering function is suitable for combining multi luminaires to realize effects transit from the main luminaire (the one set as TX mode) to last luminaire in RGB fade, RGB flow and RGB chase modes.

Ordering Illustration

The CRMX mode of main luminaire should be set as transmitter, while the CRMX mode of other luminaires should be set as receiver. Note: Only the main luminaire needs to set the length.

When the pixel is l
First luminaire (main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: l * (M-l) +X (X means order of main luminaire, M means the NO. of luminaire)

The Length calculation formula: l •N+X-l (N means numbers of luminaire used in practical)

When the pixel is 2

First luminaire (main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: 2• (M-1) +X (X means order of main luminaire, M means the NO. of luminaire
The Length calculation formula: 2•N+X-l (N means numbers of luminaire used in practical)

When the pixel is 4

First luminaire (main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: 4• (M-l) +X (X means order of main luminaire, M means the NO. of luminaire)
The Length calculation formula: 4•N+X-l (N means numbers of luminaire used in practical)

When the pixel is 8

First luminaire (main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: 8• (M-l) +X (X means order of main luminaire, M means the NO. of luminaire)
The Length calculation formula: 8•N+X-l (N means numbers of luminaire used in practical)

When the pixel is l 6

First luminaire (main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: l 6• (M-l) +X (X means order of main luminaire, M means the NO. of luminaire)
The Length calculation formula: 16•N+X-l (N means numbers of luminaire used in practical)

When the pixel is 32

First luminaire (main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: 32• (M-l) +X (X means order of main luminaire, M means the NO. of luminaire)
The Length calculation formula: 32•N+X- l (N means numbers of luminaire used in practical)
Note: Only pixel of TP4R/TP8R can be set to 32.

When the pixel is 64

First luminaire {main luminaire)

Second luminaire

Last luminaire (assume it’s the eighth luminaire)

The Order calculation formula: 64•(M- l )+X{X means order of main luminaire, M means the NO. of luminaire)
The Length calculation formula: 64•N+X- l {N means numbers of luminaire used in practical)
Note: Only pixel of TPBR can be set to 64.

Bluetooth

Short press FN button to select BT {Bluetooth switch)/Reset.
BT {Bluetooth switch): Short press the – button to turn off the Bluetooth and the Bluetooth indicator will be off Short press the+ button to turn on the Bluetooth and the Bluetooth indicator will be constant on blue.
Reset: Short press the + button to reset the Bluetooth, and the Bluetooth indicator will blink when resetting and stop blinking after successfully reset

Bluetooth MAC code is on the lower right corner of Bluetooth interface for matching with other luminaires, after which short press the MOO/MENU button can return to the previous setting.

Scan the QR code to download the “Godox Light” smartphone APP (can be used in Android and iOS).

Note: The APP can be used directly on the firstly installed device (smartphone or iPad). When change to other mobile device (smartphone or iPad), the light shall be reset before the normal connection of APP. The APP should be upgraded to version 3.0 or above.

Note: CRMX wireless and Bluetooth both use 2.4G frequency, so it’s recommended not to turn on at the same time to avoid disturbance.
Please avoid or turn off the 2.4G transmitting signal nearby for the sake of stability when using Bluetooth.

Dimming Curve

Short press the FN button to select Linear/ S-curve/Exp/Log in dimming curve interface.

Quick Start

Short press the FN button to turn on/off the quick start function.

Rotate Screen

Short press the FN button to select upward/downward in rotate screen interface. Press the FN and – button at the same time can rotate screen quickly.

Preset

Short press the FN button to select from Pl to P20 in preset interface. Short press the+ button to enter the desired preset, then short press the FN button to select Apply/Save/Cancel, and short press the+ button to confirm. If you select apply, it will go to the preset effect interface.

Note: Short press the FN button twice can return to the previous setting. There will be no “Apply” option if no effect is set in the Preset.

Battery

The battery level and estimated working time is displayed in the battery interface.

Overheat PROT

Short press the FN button to select reduce max DIM or black out

Language

Short press the FN button to choose Chinese or English in the language interface. after which short press the MOD/MENU button can return to the previous setting.

Factory Reset

Short press the FN button to choose No or Yes in the factory reset interface. If you choose “No”, short press the+ button or MOD/MENU button can return to the previous setting. If you choose “Yes”, short press the + button can restore to factory setting, after which it will turn to 100% brightness and return to the previous setting.

Version

The firmware version and upgrade information are displayed on the Version interface. For Bluetooth upgrade, please refer to the detailed tutorial of “Godox Light” APP.

Upgrade via USB disk

1. Download the new firmware to the USB disk from official websit(https://www.godox. corn/firmware-continuous-light).
2. Turn off the device. Insert the USB disk with new firmware into the Type-C USB port.
3. Turn on the device, and it will automatically enter the upgrading interface.
4. It will return to main interface after completion.
   Notes:1. New firmware must be downloaded from the official website, and keep only one BIN file in the root directory of the USB disk.

Setting Instruction

First setting| Secondary setting| Option in secondary setting| Instruction
---|---|---|---
DMX| ADD| 007-57 2| Initial address
Pixels| 7| l Pixel
2| 2 Pixels
4| 4 Pixels
8| 8 Pixels
76| 16 Pixels
32 (only available for TP4R/TP8R)| 32 Pixels
MOD| CCT 8 bit| CCT 8 bit
HSI 8 bit| HSI 8 bit
RGBWBBit| RGBWSBit
RGBWWSBit| RGBWWSBit
xyBBit| xySBit
CCT&HSI Sbrt| CCT&HSI Sbrt
CCT&RGBW 8bit| CCT&RGBW 8bit
CCT&xy 8bit| CCT&xy 8bit
GEL 8bit| GEL 8bit
CCT 76 bit| CCT76 bit
HSI 76 bit| HSI 76 bit
RGBW 76 bit| RGBW 76 bit
RGBWW76Bit| RGBWW76Bit
xy 16Bit| xy 16Bit
CCT&HSI 16bit| CCT&HSI 16bit
CCT&RGBW 16bit| CCT & RGBW 16bit
CCT & xy 16bit| CCT & xy 16bit
GEL 16bit| GEL 16bit
FX 8bit| FXS bit
FX 16bit| FX 16bit
Ultimate 8bit| Ultimate 8bit
Ultimate 16bit| Ultimate 16bit
Loss(DMX Loss Status)| Hold| After the OMX control signal is lost, continue to use the last received OMX control signal until power down

or a yal1d D X control signal is received again.

Black Out| The light is off immediately.
Hold 2 min| AfteR ( the OMX control signal.is lost. continue to use the last received OMX control signal for 2 minutes then black out Note lf ava lidOM X control signal is received wth in 2 minutes,then use the new OMX control signal
Turn on ROM
OFF| Turn off ROM
Turn on CRMX
OFF| Turn off CRMX
CRMX is in TX mode
RX| CRMX is in RX mode
Output power value = l 2dBm (only adjustab le in transmitter mode)
7 6d Bm| Output power value = l 6dBm (only adjustable in transmitter mode)
20dBm| Output power value = 20dBm (only adjustable in transmitter mode)
22dBm| Output power value = 22dBm (only adjustable in transmitter mode)
24dBm| Output power value = 24dBm (only adjustable in transmitter mode)
26dBm| Output power value = 26dBm (only adjustable in transmitter mode)
Please refer to the chapter “Ordering”
|
|
|
16|
32 (only available for TP4R/TP8R)|
64(on ly available for TPBR)|
The initial addresses of mu lti-lights combined in RGB fade/RGB flow/ RGB chase mode
The final addresses of multi – lights combined in RGB fade/RGB flow/ RGB chase mode
Turn on the Bluetooth
OFF| Turn off the Bluetooth
Reset the Bluetooth to factory setting and it will turn on automatically.
The device will automatically boot up when in adapter power supply.
Long press the device for 2s to boot up.
Easy for viewing
Apply the preset
Save| Save the preset
Cancel| Return to previous setting
Battery information
Reduce the brightness when overheating
Turn off the light when overheating
The language is Chinese
The language is English
Cancel factory reset
Restore to factory setting
Device information

luminance Data

TP2R

TP4R

6500Klux 8500Klux 10000Klux

TPBR

Technical Data

Note: V-mount battery should be 14.8Vor 26V lOOWh above (sold separately).

Battery Life(in 100% brightness)| Approx. l 20min
Charging Time| Approx 120min| Approx l SOmin
Waterproof Grade| IP65
Average TLCI| e96
Average CRI| 2:96
CCT Range| 2000K-10000K
Mode| 5 modes: CCT mode, HSI mode, RGB mode, GEL mode, FX mode
FX Types| 17
Controlling Methods| r 1.2Rio t llle etooth APP control, CRMX control, Light body
Bluetooth Controlling Distance| Max. 30m
Wireless Controlling Distance| Max. 150m
Working Environment Temperature| – 10°C~40°C
Dimension| 47mm47mm600mm| 47mm47mml 200mm
Net Weight==| 0.84kg| 1.5kg

Specifications and data may subject to changes without notice.

Power Supply
Note: The V-mount battery should be 14.8V or 26V l DDWh above and sold separately
Battery Life ( in l 00%

brightness)

| Approx 140min
Charging Time| Approx. 180min
Waterproof Grade| IP65
Average TLCI| e96
Average CRI| 2:96
CCT Range| 2000K- l 0000K
Modes| 5 modes: CCT mode, HSI mode, RGB mode, GEL mode, FX mode
FX Types| 17
Controlling Methods| OMXSl 2 control, Bluetooth APP control, CRMX control, ROM Control, Light body control
Bluetooth Controlling Distance| Max 30m
Wireless OMX Controlling Distance| Max. 1OOm
Working Environment Temperature| -1Q°C~40°C
Dimension| 47mm..47mm*2300mm
Net Weight==| 2.94kg

Warning

Operating frequency:2402MHz – 2480MHz(2.4G)/2402MHz – 2480MHz(BT)
TP2R Maximum EIRP Power: 4.58dBm(2.4G)/3.88dBm(BT)
TP4R Maximum EIRP Power: 8.63dBm(2.4G)/8.23dBm(BT)
TPBR Maximum EIRP Power: 5dBm(2.4G)/5dBm(BT)
Declaration of Conformity
GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(1 O), this product is allowed to be used in all EU member states.For more information of DoC, Please click this web link:

https://www.godox.com/eu-declaration-of-conformity/

The device complies with RF specifications when the device used at 0mm from your body.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/1Y technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you1

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases: G). The product or accessory has expired its warranty period; Q>. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;®· Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;@. The original identifying information of product or accessory is modified, alternated, or removed;@. No valid warranty card;@. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;(!). Breakage or damage caused by force majeure or accident;®· Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance

Period(month)

| Warranty Service Type
---|---|---|---
Parts| Circui t board| 7 2| Customer sends the product to designated site
Battery| | Customer sends the product to designated site
Electrical parts e.g.battery charger,

etc

| 7 2| Customer sends the product to designated site
Other Items| Lamp body, lamp cover, loc king device, package.etc| NO| Without warranty

Godox After-sale Service Call 0755-29609320-8062

Wechat Official Account

0755-25723423 W!’lll: godox@godox.com
GOOOX Photo Equipment Co., Ltd.
Add.: Building 2, Yaochuan Industrial Zone, Tang wei Community, Fuhai Street, Bao’ an District, Shenzhen
518103, China Tel: +86-755-29609320(8062) Fax: +86-755-25723423 E-mail: godox@godox.com
www.godox.com
Made in China I 705-TP2R00-03
6odox
KNOWLED
TP2R/TP4R/TP8R
RGBWW{lit~n
KNOWLED
www.godox.com
Made in China I 705-TP2R00-03

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>