ZEEVA ET-0784-TX COVERT Foldable WiFi Drone Instruction Manual
- June 12, 2024
- Zeeva
Table of Contents
AGES 14+
Instruction Manual
Thank you for purchasing the Wifi Covert drone.
This manual provides more information about this drone, please read the
instructions before using.
DD MM YYYY
Date: 16 06 2023 SKU: ET-0784 Drone| Release N.: DR1
Product Name: RC Drone| Brand:| Customer:five BELW
---|---|---|---
Dev. Stage:
IM DESIGN| Printing: CMYK| Category: Accessories
Season: FW 2023 Guideline Reference:| DOCUMENT: IM ARTWORK|
Product Overview
- Upper Casing
- Lower Casing
- Propeller
- Protective Guard
- Arm
- Battery
- Motor
- Camera
Specification
Frequency 2.46Hz 8 – Camera Power Supply: Covert Drone: 3.7V 600mAh Li-ion
Rechargeable Battery (Included) Remote Controller: 3 x AA 1.5V Alkaline
Batteries (not Included) Play Time: About 6 minutes
Camera: 720p
Photo Resolution: 1280 x 720p Video Resolution: 640 x 480p
Packege Contents
Remote Control
1 – Device Holder
2 – Left side fly fine-tuning
3 – Left joystick
4 – One-key Take off
5 – One-key Landing
6 – Power switch 7 – Backward fine-tuning
8 – Forward fine-tuning| 9 – Right joystick
10 – Right side fly fine-tuning
11 – Headless Mode
12 – High/low speed
13 – One-key Flips & Rolls
14 – One-key calibration
---|---
Drone Battery Charging
Remove the lithium battery from the bottom of the drone.
Connect USB charging cable with the charging interface of the lithium battery.
CAUTION: The micro USB charging cable induded with this item is intended
for use with is product. Only use the induded micro USB charging cable to
charge this product.
Remote Control Batteries Installation
Open the remote control battery cover
Remote control battery installation
Open the battery cover and insert the 3 M batteries correctly according to the electrode instructions. (Batteries not included)
Drone Propellers Installation
To Open:
- Open the front arms first (closet to camera,
- Then open the back arms.
To Fold Close:
- Fold the back arms first
- Then fold the front arms.
Assembling protective guard
- Align the protective guard with the two slots below.
- Press firmly on the arrow position.
Assembling propellers
- Correspond the Propellers with the hex nuts of the crankshaft (the arm Identification Is consistent with the Propellers identification)
- Tighten the screws clockwise.
Connection
Signal connection of transmitter and receiver Turn on the drone and place it
on a level surface, the indicator light of transmitter and the LED of drone
flashing. Push the throttle joystick to the highest point then push back to
the lowest point, and when you hear two beeps, the indicator light of
transmitter and the LED of drone become normally on, the signal connection as
completed.
Transmitter calibration
Apply transmitter calibration when the drone fails to take oft vertically.
Press the “One-key calibration” button when the lights of drone are on and
then start flashing and keep on again, the calibration is complete. The drone
must be placed on a horizontal surface in a steady state when the calibration
is conducted.
Start Your Flight
Press the -One-key Take off’ button, the drone blades rotate and automatically fly to a height of 5 feet.
Basic Flight
Use the left joystick to controf the fight at and turn letthigM, and the right
joystick to control the forward, backward, left and right aide flight
directions.
Left Joystick
Right joystick
Flips & Rolls
When the drone is reaching more than 10 feel high, click ‘One-key Flips &
Rolls- and move the right joystick to a certain direction, the drone we rotate
In that direction.
Speed Settings
Heedless Mode
The flight direct Ion of drone Is subjected to the *recta) of remote control.
- When drone adjust the frequency, the drone Is default as common mode. Then the indication light of drone is normally on. When you press the headless function key of remote control, the remote control beeps once and enters headless state. When you press the headless function key again, you listen to a long beep sound and the drone exits the headless mode.
- In the heedless state, operator doesnl reed to Identify the direction of nose, but control the drone amercing to the operation lever of remote control. Hover Mode When you release the left joystick (throttle) after the ascent / descent action, the drone will hover at a certain height
Left Joystick
Fine-tuning function
When deviating from course, eke ‘line-turning tor calibration unit the drone Is back to normal.
Smartphone App Downlead
Method 1: Scan the QA Code for quick download
Method 2: Search “WOW Drone” in the Apple app store or Google Play as the app
download lirm@tations are not the tame In all the countries.
Please nated the: the method of downinad maybe differant, bus you can try all
the three mathods provided for you above. ‘Compatible With: IOS & Android
Remote Control App
Connection settings:
- Connect the power supply of the module, and the indicator fight ‘Starts to flash, which indicates that the mobile phone ts waiting to be connected.
- Open the mobile phone setiings option, start WiFi, and search “WIFI_BK_DOOCKXX * in the search list . click Connect until connected appears, which means the connection Is successiul.
- Open the software and click the “Start Flying’ icon to enter the real-time image transmission intertace.
Notice
Pisase read this instruction manual carefully before operating the product.
Please do not operate the product in the gale.
The flying ground should be the local field and legal for remote contro!
flying.
Please do not operate the product in forbidden zone or around people or
animals.
Keep the aircraft a certain distance (at least 2-3 meters) from others when
playing together.
Warning
This product is suitabie fo be used by people who has operating experience in
flying model or aged no teae than 14 yeers old.
This product is not a toy but 8 precise equipment integrating mechanics and
electronice with expertise of Berodynamics and high-frequency tranamitiing. 8
requires correct assembly and debug 80 as to prevent the accident from
happening. The ueer should operate or control it in a sele way.
Please do not put the product in your mouth 10 prevent choling hazard of email
parts.
Pleaes do not put the finger into available interspaces.
Pteace do not play the product in a brutal way such as throwing, crashing or
twisting it.
Pleage store the amaller-sized product accessories in places that are out of
reach of children, in order to avoid the occurrence of accidents.
The product is very powerful. When ftying for the first time, obeerve
carefully. The joystick muat be slowly pushed in order to prevent the product
from ascending 100 quickly and reauit in unnecessary collision and damages.
When the flight has ended, the power supply of the remote conirol should be
awitched off and also switch Off the power supply of the product.
Avoid placing the batteries in places in high temperatures and avoki exposure
to heat.
When young children ere operating the product, it shall be ensured that the
adulla are guiding and making eure the product control is within the viewing
range of the controller ( or inetructor}so thei t makes the control of the
drone more convenient.
‘When the product is not in uee, please switch off the power supplies of both
the aircrak and the remote control, and remove the batteries trom the remote
control.
Please note that we won’t take any reaponelbility for any wrong operation as
this may result In severe injury or loss ol property, and we cannot control
the operating procees during the tine when the user assembles or uses this
product.
Once this product ie sold, we won’t be responsible for any saiety
responsibility during the time the user operates or uses cortrots this
products.
Care and Maintenance
Always use dry and soft cloth to clean this product.
Avoid this product from being exposed to sunlight or heat.
Avoid Inmersing these toys in water, otherwise, the electronic parts may be
damaged.
Check regulary and Inapect the plug and other accessories. If ary damages are
discovered, please stop using immediately, und it ts completely repaired in
good working condition.
IMPORTANT: BATTERY INFORMATION
CAUTION: TO PREVENT BATTERY OVERHEAT
- Wf the product needs to recharge, please wait 10-15 minutes to let battery cool before charging.
- Do not over charge the battery. If the battery becomes too hot to touch while charging, then remove from charger immediately and leave to cool, othenvise battery may become damaged. Always pay attantion to when you are charging the battery. Do not disassemble of reconstruct battery. Do not connect the battery to an electrical outlet.
LHON BATTERY CHARGING WARNING STATEMENT:
The input to the product is SV 1A.
In order to charge the product in safe manner and reiiable conditions, plaase
onty adopt Certified appropriate charger! adapter for charging the product.
Only charge the product st ambient temperatures between 10 °C/ 50 °F and 40
°C/104 °F.
Do not heat above 70 °C/158 °F, eg. Do not expose to sunlight or throw into
fire. Please note that we won’t take any responsibility for any wrong
operation (eg. Voltage higher than 5V) as this may result in severe injury or
loss of property, and we cannot control the operating process during the time
the user using this product.
BATTERES:
WARNING: TO AVOID BATTERY LEAKAGE
- Be sure to insert the batteries correctly, and always follow the toy/game and battery manufacturers’ instructions.
- Do not mix oid and new batteries or alkaline, standard(carbon-zinc) or rechargeable (nickel-cadmium) batteries,
- Always remove weak or dead batteries from the product. 4) Remove the battery if the product is is left unused for a long period of time.
CAUTION
The micro USB charging cable included with this Item is intanded for use with
this product. Only use the included micro USB charging cable to charge this
product.
FCC Statement
This device complies with the part 15 of the FCC rules. Operation is subject
to the following two conditione:(1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limés
for a Class 8 digital device. pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used In
accordance with instructions may cause hermful interference to radio or
television reception, which can be determined by tuming the equipment off and
on. The user is encouraged to try to correct the interference by one or more
cf the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect ths squipment into an outlet on a circuit different from that to which the receiver Is connected.
- Consult the dealer or experienced radio / TV technician for help.
RF Warning Statement.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
FCC ID: 2ADMS-ET-0784-RX
FCC ID: 2ADM5-ET-0784-TX
Itemn# ET-0784
Distributed by 1616 Holdings, Inc.
701 Market Street, Suite 200
Philadelphia, PA 19106
Made in Shantou, China
Keep All Relevant information for Future Reference
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>