FYNE AUDIO Vintage Classic X Floorstanding Speaker User Guide
- June 12, 2024
- FYNE AUDIO
Table of Contents
FYNE AUDIO Vintage Classic X Floorstanding Speaker
Product Information
The Fyne Audio Vintage Classic loudspeakers are designed and constructed to
the highest standards by experienced engineers and artisans in Scotland. They
incorporate cutting-edge technology and innovative design to deliver best-in-
class performance. The speakers feature Fyne Audio’s IsoFlareTM point source
driver, which provides outstanding stereo imaging and radiates sound from a
single point. The drivers are built with a custom tooled rigid cast aluminum
chassis to eliminate unwanted vibrations and ensure optimal sound quality. The
speakers also utilize a unique waveguide for the high-frequency unit to
achieve a flat frequency response and avoid internal reflections. The low-
frequency section features a FyneFluteTM surround and a multifibre paper cone
for natural midrange and clean transient behavior.
Product Usage Instructions
- Before installing the loudspeakers, read the manual in full for safety reasons and to achieve the best performance.
- When unpacking, follow the instructions carefully to avoid injury or damage. It is recommended to have the help of an assistant.
- Retain the packing for possible future use.
- Check the contents of the accessories box, which include:
- Floor coupling spike M12 (x8)
- Spike locking wheel (x8)
- Floor protection cups (x8)
- Bi-wire links (x4)
- Position and fit the floor coupling spikes according to the instructions provided.
- Select an appropriate amplifier for optimal performance.
- Choose high-quality cables for connecting the speakers.
- Connect the speaker cables following the recommended guidelines.
- Ensure proper earth connections for safety.
- Make necessary adjustments to optimize speaker performance.
- Store the grille properly when not in use.
- Take care of the cabinet to maintain its condition.
- Refer to the warranty information for any claims or inquiries.
- Review the detailed specifications provided in the manual.
INTRODUCTION
Thank you for choosing Fyne Audio Vintage Classic loudspeakers, proudly designed by our experienced team of engineers, and constructed to the highest standards by artisans in our own facility in Scotland. We believe they will give you many years of listening pleasure.
- Before installing these loudspeakers please read this manual in full, both for safety reasons and to ensure you achieve the best performance possible.
- When unpacking, please follow the instructions carefully, to avoid causing possible injury or damage. Please ensure you have the help of an assistant.
- Please retain packing for possible future use.
- Check the contents of the accessories box
- Your accessories box includes
- Floor coupling spike M12 (x8)
- Spike locking wheel (x8)
- Floor protection cups (x8)
- Bi-wire links (x4)
CROSSOVER
Although simple in topology, the design is computer optimized, and fine-tuned subjectively by critical auditioning. The crossover makes use of high-quality precision components, including low-loss LF laminated iron core inductors, high-power precision resistors, and high-grade HF polypropylene capacitors. High-quality gold-plated bi-wire terminals are used, together with Van den Hul Matched Crystal OFC wiring with high-purity silver coating, for transparent signal transfer. The components are hard-wired on fibreboard panels to minimize vibration. A specially designed autotransformer using the highest grade silicon steel laminations impedance matches the HF compression driver to the amplifier, with varnish vacuum impregnation to eliminate distortion caused by winding vibration. A grounding terminal is fitted to minimize the effect of radio frequency interference masking fine detail. BASSTRAX™ TRACTRIX DIFFUSER SYSTEM The Vintage Series employs a downwards firing port arrangement using a twin cavity reflex loading system. This loading system broadens the tuning frequency to reduce cone excursion and acts as a muffler, blocking standing waves produced by the main internal port.
Below the vent in the base of the loudspeaker, the BassTrax™ Tractrix profile diffuser is used to convert the plain wave energy to an expanding spherical 360-degree wavefront, dispersing energy uniformly into the room. This Tractrix profile has been previously applied to horn loudspeakers by Voight in the 1920s, but the application to a diffuser of this type is novel and has been granted a patent. The BassTrax™ Tractrix profile is known to maintain a 90-degree angle at each intersection of the expanding wavefront, thus avoiding reflections. This clever arrangement also makes the loudspeaker less critical of room positioning.
ENCLOSURE
A high-density fibreboard construction is used to ensure an extremely rigid
and low-coloration structure. The drive unit is coupled to internal bracing
panels through damping material to absorb energy. Each cabinet is uniquely
crafted and walnut veneered, accented with gold anodized metalwork. Heavy-duty
support spikes enable precise leveling, with the provision of machined
aluminum cups for protection on wooden floors.
POSITIONING & FITTING FLOOR COUPLING SPIKES
With the loudspeaker still located on the foam end cushions, start by
positioning the loudspeakers with their rear at least 0.5m from the rear wall.
The proximity of a side wall should be no closer than 1m (Fig. 1). Remember
that proximity to the rear and side wall will influence both the bass
performance and stereo imaging. Excessively reflective or dissimilar adjacent
walls will be detrimental to the stereo image precision. The imaging focus is
influenced by toeing in the cabinets towards the listening position. The
BassTrax™ diffuser system, however, will serve to make the loudspeaker less
sensitive to boundary conditions than with a conventional design Lift the
loudspeaker off the foam end cushions and fit the 4 floor coupling spikes and
locking wheels. When the loudspeaker is in position, level by adjusting the
spikes and tighten the locking wheels (Fig. 2). Ensure the protective cups are
used under the spikes to avoid damage to wooden or other delicate floor
surfaces.
AMPLIFIER CHOICE
The advisable range of amplifier powers is detailed in the Specification. Responsible use with higher-powered amplifiers is possible, due to the robust design of these loudspeakers. We do not advocate any specific amplifier technology, i.e. transistor versus valve (tube). As with any high-resolution loudspeaker system, it is the quality of the amplification that is paramount in extracting maximum performance from your loudspeakers. Some customers may wish to use valve (tube) amplifiers such as single-ended triodes, with output powers less than the minimum recommendation. This will not cause damage to the loudspeakers but will restrict the maximum volume and dynamic range, especially in large rooms. If you are considering the purchase of a new amplifier, your dealer will be able to give you recommendations that work well.
CABLE CHOICE
It is important to use cables of appropriate quality for such high-performance
loudspeakers. While from a technical perspective, adequately low electrical
resistance is necessary to minimize losses and maximize amplifier damping. The
physical construction of the cable including conductor type and purity,
together with insulation characteristics have considerable influence on the
sound quality. The optimum cable is both subjective and system dependent; your
dealer will be able to give advice. Cables should be terminated in high-
quality connectors, either 4mm banana or spade.
CONNECTING SPEAKER CABLES
Ensure the amplifier is switched off before connecting cables, to avoid damage. Ensure connections are made positive to positive and negative to negative between the loudspeaker and the amplifier. The loudspeakers are provided with two sets of terminals, one for the HF and one for the LF section. The wiring may be done in either single-wire mode or bi-wire mode. The latter will provide optimum performance. When using a single cable, wire as shown (Fig. 3), fitting the link cables provided. The best sound quality will generally be achieved when connecting to the HF terminals. For bi-wire operation, ensure the link wires are not fitted, and wire with two sets of cable, or a dedicated bi-wire cable (Fig. 4). This will ensure the best possible sound quality.
A further option is bi-amping, where the LF and HF sections of the loudspeaker are each driven from their own amplifier, for further enhancement in sound quality. Either two stereo power amplifiers or four monoblock amplifiers may be used. If using either two stereo power amplifiers or four monoblock amplifiers may be used. If using two stereo amplifiers, it is recommended that one is used as the LF channel to both loudspeakers and the other HF (Fig. 5). To avoid amplifier damage, the bi-wire link cables must not be in place.
EARTH CONNECTION
The loudspeaker is provided with an earth or ground connection, connected to the drive unit chassis. The purpose of this is to ground any radio frequency interference that may get back to the amplifier, reducing fine detail and resolution. A separate earth wire may be used for this purpose, but the best results will be obtained by using a dedicated screened loudspeaker cable.
ADJUSTMENTS
The Vintage Classic Series are provided with two adjustment controls on the
front panel, to achieve optimal performance in terms of both the listening
environment and the listener preference. The upper ‘Energy’ control alters the
level of signal fed to the tweeter, from the crossover point upwards, giving
control over how bright the presentation sounds (Fig. 6). The lower ‘Presence’
control only affects the lower treble region of 2.5 – 5.0kHz, influences
articulation and vocal clarity, and has an effect on image depth (Fig. 7).
Start with both controls in the central (level) position and make small
adjustments with well-recorded program material that you are familiar with.
Achieving the correct presentation is equivalent to focusing the lens on a
camera, to achieve the most realistic sound-staging depth.
FIG 7. PRECISE ADJUSTMENT
FIG 6.
GRILLE STORAGE
Although the magnetically attached grilles are designed for maximum
transparency, we always recommend removal for the best possible sound quality.
The grilles may be magnetically fixed to the rear of the loudspeaker for
neatness and to avoid damage. Remove the grille from the front of the
loudspeaker (Fig. 8), and locate on the rear (Fig. 9).
CARE OF CABINET
The cabinet may be dusted with a lint-free cloth, such a muslin. Use a
slightly dampened cloth to remove any marks. As wood is a natural material,
avoid exposure to extremes of heat, humidity, and direct sunlight for extended
periods of time.
If unused for long periods of time, you may wish to cover the loudspeakers
with the cloth bags they were packaged in, to provide protection. On no
account use solvents or abrasive materials, as this will cause damage and
invalidate
the warranty.
WARRANTY
- No maintenance of the loudspeaker is necessary.
- Please register your Fyne Audio Limited product online at www.fyneaudio.com. All of our products have been produced and tested with care and precision to give first-class service.
- All passive loudspeakers are guaranteed for a period of 7 years from the date of purchase from an authorized Fyne Audio Limited dealer. This warranty is subject to the absence or evidence of misuse, overload, or accidental damage, applies only to the original registered owner, it is nontransferable, and covers only genuine Fyne Audio Limited products with the original undamaged serial number and proof of purchase.
- All active and electronic components are guaranteed for a period of 2 years from the date of purchase from an authorized Fyne Audio Limited dealer subject to the absence of, or evidence of, misuse, overload or accidental damage.
- If at any time during this warranty period, the equipment proves to be defective for any reason other than an accident, misuse, neglect, unauthorized modification, incorrect installation or connection, matched with improper equipment or fair wear and tear, we will repair any such manufacturing defect or, at our option, replace it without charge for labor, parts or return carriage.
- If you suspect a problem with a Fyne Audio Limited product, in the first instance, discuss it with your Fyne Audio Limited dealer. If you require further assistance, then we ask that you deal directly with your local Fyne Audio Limited distributor. If you cannot locate your distributor please contact Fyne Audio Limited Customer Services, via our website listed above or at the e-mail enquiries@fyneaudio.com
- Do not ship any product to Fyne Audio Limited without previous authorization.
LIABILITY
Other than the warranty and services set out in this warranty, to the fullest
extent permitted by law, Fyne Audio Limited and its Authorised Distributors
shall not be liable to you and/or any third party or entity whatsoever for:-
any loss, damages, and/or malfunction caused to any product(s) which is/are
connected to any of the Fyne Audio Limited products any damages, loss and
liability (except for any personal injuries or death), whether direct,
indirect, incidental, consequential special, punitive or otherwise, howsoever
caused by, arising out of, or otherwise in relation to the installation,
delivery, use, service, repair, replacement and/or maintenance of the Fyne
Audio Limited product; or any damages, loss and liability (except for any
personal injuries or death) under this warranty in respect of any act,
omission, or negligence of any of their technicians, employees, agents,
representatives or independent contractors relating to the actual or purported
performance of any of the obligations under this warranty. Without limiting
the above, the maximum liability of Fyne Audio Limited and its Authorised
Distributors under this warranty shall not in any event or under any
circumstances exceed the actual purchase price paid for the Fyne Audio Limited
product(s).
SPECIFICATIONS VINTAGE CLASSIC X
- System type 2 way, downwards firing port, with BassTrax™ Tractrix diffuser
- Recommended amplifier 20 – 280
- power (Watt RMS)
- Peak power handling (Watt peak) 560
- Continuous power 140
- handling (Watt RMS)
- Sensitivity (2.83 Volt @ 1m) 94dB
- Nominal impedance 8 Ohm
- Frequency response 28Hz- 26kHz
- (-6dB typical in the room)
- Drive unit complement
- t 1 x 250mm IsoFlare™ point source driver, multi-fiber bass/midrange cone, with 75mm titanium alloy dome compression tweeter, ferrite magnet system
- Crossover frequency 750Hz
- Crossover type Bi-wired passive low loss, 2nd order low
- pass, 2nd order high pass
- Cryo-Lite treated
- System adjustments High frequency energy (750Hz – 26kHz) +/- 3dB
- Presence (2.5kHz – 5.0kHz) +/- 3dB
- Dimensions – HxWxD 918 x 450 x 381mm
- (40.9 x 18.4 x 19.3”)
- Cabinet construction High-density fibreboard, walnut veneered with extensive internal bracing
System type 2 way, downwards firing port, with BassTrax™ Tractrix diffuser
- Recommended amplifier 20 – 350 power (Watt RMS)
- Peak power handling (Watt peak) 700
- Continuous power 175
- handling (Watt RMS)
- Sensitivity (2.83 Volt @ 1m) 96dB
- Nominal impedance 8 Ohm
- Frequency response 25Hz- 26kHz
- (-6dB typical in the room)
- Drive unit complement 1 x 300mm IsoFlare™ point source driver, multi-fiber bass/midrange cone, with 75mm titanium alloy dome
- compression tweeter, ferrite magnet system
- Crossover frequency 750Hz
- Crossover type Bi-wired passive low loss, 2nd order low pass, 2nd order high pass
- Cryo-Lite treated
- System adjustments High frequency energy (750Hz – 26kHz) +/- 3dB
- Presence (2.5kHz – 5.0kHz) +/- 3dB
- Dimensions – HxWxD 1102 x 572 x 591mm (43.4 x 22.5 x 23.3”)
- Cabinet construction High-density fibreboard, walnut veneered with extensive internal bracing
Thank you for choosing Fyne Audio loudspeakers, proudly designed by our experienced team of engineers in Scotland, and constructed to the highest standards