MINELAB 0054 Metal Detector Instruction Manual

: June 12, 2024
: MINELAB

Table of Contents

SAFETY CONSIDERATIONS
REGULATORY INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MINELAB 0054 Metal Detector Instruction Manual

ADVICE AND SAFETY INSTRUCTIONS
For complete product specification and operational guidance, read the Instruction . www.minelab.com/productmanuals Manual at Alternatively, please contact us to make arrangements for a copy.

ASSEMBLY INSTRUCTIONS
For guidance on detector assembly, please refer to the Getting Started Guide included or visit: . www.minelab.com/product-manuals The Minelab website also provides information on accessories available for your detector.

WARRANTY TERMS
www.minelab.com/support/ Please refer to for full warranty terms and product-warranty conditions. Register your product warranty online at register.minelab.com

SAFETY CONSIDERATIONS

Keep out of reach of children, small parts are a choking hazard.
Do not mutilate the batteries.
Dispose of batteries as per local regulations.
Only charge the detector and accessories according to the instructions in the manual.
Do not dispose of the detector or accessories in a fire.
Disconnect coil before packing/storing as luggage.
CAUTION Risk of explosion if battery is replaced by an incorrect type.
CAUTION — Only charge the battery in ambient temperatures between 0°C and 40°C.
Headphone use at HIGH volume may cause reduced awareness of surroundings and could lead to hearing damage. Use at lower volumes advised.
Adult supervision required when used by children

REGULATORY INFORMATION

Federal Communications Commission (FCC) (as applicable) Statements

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been Part 15.105 NOTE: tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

US Responsible Party: 123 Ambassador Drive, Suite 123, Naperville, IL 60540, USA

ComplianceManager@minelab.com.au

Compliance Statements for Canada This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. This device complies with RSS-Gen notice: Industry Canada’s license-exempt

RSSs. Operation is subject to the following two conditions: 1) This device may not cause interference; and 2) This device must accept any interference, including interference that may cause undesired operation of the device.

Modification

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

Simplified EU & UKCA Declaration of Conformity

Hereby, Minelab Electronics Pty Ltd declares that the radio equipment type [Refer to detectors listed in Table 1] complies with Directive 2014/53/ EU and The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of the EU & UKCA declarations of conformity are available at the following internet address: . www.minelab.com/compliance

EU Importer: MINELAB ELECTRONICS PTY LTD Second Avenue, Mawson Lakes, SA 5095, 2 Australia

License / Permit
The equipment operator is responsible for investigating and obtaining any required local license or permit for metal detecting activities.

WEEE:

This symbol indicates that the equipment and its electrical accessories should not be disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and should be taken to a certified collection point for recycling and proper disposal. Refer 2012/19/EU (Waste Electrical and Electronic Equipment).

RADIO FREQUENCY SPECIFICATION

Table Icon

CERTIFICATION SCHEME ID

Table Icon

Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries. | The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by [Minelab Electronics Pty Ltd] is under license. Other trademarks and trade names are those of their respective owners. M

Certification and logo usage dependant on product and region
Symbols