Outwell 220V1-BT Olida Stove Instruction Manual
- June 12, 2024
- Outwell
Table of Contents
JIMBU STOVE
MODEL: 650800 / 218-BT| 
---|---
OLIDA STOVE
MODEL: 650604 / 220V1-BT| 
ANNATTO STOVE
MODEL: 650804 / 204PI-BT| 
INSTRUCTION MANUAL
Read these instructions for use carefully so as to familiarize yourself with
the appliance before connecting it to its gas cartridge.
Keep these instructions for future reference.
TECHNICAL DATA:
Appliance name:| Jimbu Stove (650800/218-BT)| Olida Stove (650604/220V1-BT)|
Annatto Stove (650804/204P1-BT)
---|---|---|---
Type of gas:| Butane-propane mixture
Category:| Direct pressure
Type of gas cartridge:| All 3 appliances should only be used with Primus
220693, 220794
or 220294 Butane-propane mixture gas cartridges compliant with EN 417.
Injector size:| 0 0.30 mm (Burner) & 0 0.20 mm (Grill)| 0 0.28 mm| 0 0.30 mm
Nominal rate in g/h and
in kW (Hs):| 3.5 kW (255 g/h) (Burner) & 1.5 kW (109 g/h) (Grill)| 2 x 3.0 kW
(218g/h)| 2 x 3.5 kW (255 g/h)
ASSEMBLY
- 1. Windshield protection
- Grate for pots or pans
- Grill grate with non-stick coating (Only applicable for Jimbu Stove / 650800-218-BT)
- Appliance lid
- Individually controlled burner knob
- Individually controlled burner knob
- Auto piezo ignition
- Inlet for connector / gas hose
- Drip tray (only applicable for Jimbu Stove / 650800-218-BT)
- Easy-close latch
- Gas hose
- Connector with female valve and female thread
- Gas valve adaptor with tap
- Connection points
INSTRUCTION MANUAL
- Make sure that the appliance has been assembled correctly before using it
- Open the lid (4) and attach both side windshield protections (1) to the lid. Make sure to connect the two small hooks on the inside of the lid properly to the small connection holes molded on each windshield (1).
- Take the gas hose (11) with the connector (12) and push the female valve gently but firmly into the inlet before screwing the female threaded collar tightly to the inlet of the appliance.
Applicable for Jimbu Stove:
- Make sure to place the grill grate (3) in the molded holes on the right-hand side of the appliance so it fits properly. It should not be loose.
- Place the grate (2) into the molded holes on the left-hand side of the appliance.
- Slide in the drip tray (9) from the back and under the appliance.
Applicable for Olida & Annatto Stove:
- Place the grate (2) into the molded holes on the appliance.
OPERATION
- CAUTION: Use outdoors only.
- When in use the appliance should be placed in a location that is well-ventilated and protects it from direct draughts.
- Accessible parts may be very hot. Use gloves and sturdy long barbecue tools when cooking.
- Keep young children away from the appliance.
- Do not misuse the appliance or use it for other purposes than what it is intended for.
- Do not modify any parts of the appliance.
- Do not try to repair the appliance. If you are not able to rectify any fault following these instructions, contact the dealer or Outwell Customer Service (contact details below).
- Never leave the appliance unattended when lit.
- Handle the appliance with care. Make sure not to drop it. Do not move the appliance during use.
- Check that seals are in place and in good condition before connecting to the gas cartridge.
Do not use the appliance if a seal is damaged or worn.
- Do not use the appliance if it is leaking, damaged or does not operate properly.
- The appliance shall be operated on a stable and horizontal surface.
- The appliance shall be used away from flammable materials with minimum distances to any adjacensurfaces (wall, ceiling) as shown below:
- Applicable for Jimbu Stove: Hot fat may drip out at the bottom of the appliance. Do not light your appliance on a greasy surface.
Connecting your appliance to a gas cartridge
To be able to use your appliance you will need to purchase a gas cartridge
which is suitable for this specific appliance. Please see TECHNICAL DATA table
for information regarding the gas cartridge.
-
Position the gas cartridge at the side of your appliance, keeping in mind that the cartridge must be
kept away from heat and in a safe and upright position. -
Make sure that the tap on the adaptor (13) is fully closed by turning it clockwise towards the symbol “–“.
-
Make sure that both individually controlled knobs (5+6) are closed by turning them fully clockwise towards the small “•” symbol.
-
Carefully screw the gas cartridge onto the adaptor (13) while taking care not to cross thread.
Screw down until the sealing washer meets the cartridge (hand-tight only). -
Always check for leaks at all joints before lighting the appliance.
-
Never leave the adaptor (13) attached to the gas cartridge if the hose with connector (12) is disconnected from the appliance.
Lighting Your Gas Appliance
- Make sure your gas appliance is assembled and gas cartridge connected according to above instructions.
- Open the tab on the adaptor (13) by screwing the tab counterclockwise towards the “+” symbol.
- Open the individually controlled burner knob 1, 2 or both (5+6), depending on which burner you want to use, by screwing the knob(s) counterclockwise x away from the small “•” symbol.
- Hold and push the auto electric igniter (7) to ignite the burner(s).
- If it fails to ignite after 3-5 attempts close the tap and wait 5 minutes to allow for the unburned gas to evaporate before making a new attempt.
- When the burner is lit, turn the control knob(s) (5+6) clockwise to decrease the heat intensity or extinguish, and counterclockwise to increase.
- Do not open the valves beyond the point where maximum intensity is reached as this may cause unnecessary flaring and waste gas.
- Do not move the appliance or gas cartridge once lit as this may result in flaring. A warm-up period of about 1 minute is required to avoid flaring.
- Avoid twisting of the flexible hose.
- If the gas pressure drops or the gas will not light, check if there is still gas left in the cartridge.
If there is gas left in the cartridge the gas temperature may be too low.
For your safety – if you smell gas
- If there is a leak on your appliance (smell of gas), take it outside immediately into a well- ventilated, flame free location where the leak may be detected and stopped. If you wish to check for leaks on your appliance do it outside. Do not try to detect leaks using a flame, use soapy water.
- If odour persists, contact the dealer or Outwell Customer Service (contact details below) and stop using the appliance immediately.
CHANGING OR DISCONNECTING GAS CARTRIDGE
- Always disconnect the gas cartridge from the appliance when not in use.
- The cartridge can be dis- or reconnected even if some gas remains.
- Make sure to turn off the appliance completely by screwing the tab on the regulator (13) fully clockwise towards the symbol “-“ & both knobs (5+6) fully clockwise towards the symbol “•”. Be careful as the appliance could be hot.
- The gas cartridge shall be changed in a well-ventilated location, preferably outside, away from any sources of ignition, such as naked flames, pilots, electric fires and away from other people.
- Carefully unscrew the gas cartridge from the adaptor (13).
- Check the contents of a cartridge by shaking it and listening for the sound of liquid gas.
- Dispose of the cartridge as per instructions printed on the cartridge.
- To ensure a safe connection of a new gas cartridge to your appliance please read the sections ‘ASSEMBLY’ and ‘OPERATION’.
CLEANING & MAINTENANCE
- Visually check the general condition of the appliance and clean it on a regular basis.
- Ensure the appliance has cooled off completely before cleaning.
- Use a wire brush, steel wool or a scouring pad to clean the grate (2).
- Interior surfaces of the appliance housing cover should also be washed with hot soapy water.
- Check the burner regularly to see that it is free from insects and spiders which may block the gas system.
- Check the seals regularly to ensure that they are in good condition. If there is any sign of wear and tear the seals must be replaced with new ones. Contact the dealer or Outwell Customer Service (contact details below).
Applicable for Jimbu Stove:
- Use a soft cloth with warm soap water to clean the grill grate with non-stick coating (3) to avoid any scratches on the coating.
- Do not use metal utensils on the grill grate (3) as this will damage the coating.
Please discard grill grid (3) if the coating is cracked or damaged.
HOW TO CHECK FOR LEAKS WITH SOAPY WATER
- Use a soft cloth and wring it up in soapy water.
- Apply a small amount of soapy water to all joints of gaseous parts.
- If there is a leak, you will be able to see bubbles in the soapy water.
- If you detect a leak stop using the appliance immediately and contact the dealer or Outwell Customer service (contact details below).
STORAGE
- Ensure the appliance has completely cooled down.
Disconnect the gas cartridge before you store the appliance away. Keep both the appliance and cartridge in a dry and well-ventilated place, safe from dust and dirt, and away from heat and direct sunlight.
Applicable for Jimbu Stove:
- Remove the drip tray (9) and clean it with soapy water.
outwell.com
Outwell® is a reg. trademark of Oase Outdoors
EU: Kornvej 9, DK-7323 Give, Denmark
UK: One Glass Wharf, Bristol, BS2 0ZX
Outwell Customer Service
e-mail: info@outwell.com
Tel.: +45 70 22 85 00
**** P.I.N. 2531/CS/0063
© 12/2021 Oase Outdoors ApS. Made in China