SIGMA 18552 Blaze Flash Flashing Rear Light Instruction Manual
- June 12, 2024
- SIGMA
Table of Contents
SIGMA 18552 Blaze Flash Flashing Rear Light Instruction Manual
ACCESSORIES
Art.-Nr. 18552
Art.-Nr. 18553
Art.-Nr. 00481
INFORMATION
EN SIGMA-ELEKTRO GmbH hereby declares that the BLAZE FLASH complies with the
fundamental requirements and other relevant regulations of Directive
2014/30/EU and RoHS Directive 2011/65/EU. You can find the CE declaration at:
ce.sigmasport.com/blazeflash
UKCA STATEMENT
We, SIGMA-ELEKTRO GmbH, declare that the equipment above has been tested in
our facility and found compliance with the requirement limits of applicable
standards, in accordance with the Radio Equipment Regulations 2017 and the
Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012. The test record, data evaluation and
Equipment Under Test (EUT) configurations represented herein are true and
accurate under the standards herein specified.
FCC DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation. The grantee is not responsible for any
changes or modifications not expressly approved by the party responsible for
compliance. Such modifications could void the user’s authority to operate the
equipment. This equipment should be installed and operated with a minimum
distance of 5 millimetres between the radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
MOUNTING
Do not cover the rear light!
Before mounting, clean and degrease the seat post to ensure a tight fit. When
fixing the device, ensure that the silicone strap is tight enough that the
rear light cannot move on its own and is not easily moved. Mounting height
between 250 -1200 mm.
The BLAZE FLASH is a self-calibrating kinetic brake light that is also equipped with a brightness sensor. During calibration, the yellow indicator LED (Fig. 1) flashes for about three seconds, then lights up continuously, indicating AUTO mode.
ALIGNMENT
Final side of the tail lamp perpendicular to the roadway and at right angles to the vehicle center axis.
BUTTON
BATTERY INDICATOR
The battery needs to be charged immediately if the monitoring device/blue indicator has been activated. The LEDs are not replaceable. If an LED fails, replace the tail light.
CHARGING
Ensure that the sealing marked red is always closed correctly after charging.
Energy extraction through the Micro USB port is not possible. These lamp needs to be replaced in case of defective light source.
During charging, the battery monitoring system lights up yellow. If the battery is ready for use again, the battery monitoring system goes out.
LED MODE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>