GPI 01N31GM Compact 1 NPT(F) Electronic Totalizer User Manual
- June 12, 2024
- GPI
Table of Contents
01N31GM, 01N31LM and
01N12LM Electronic Water Meters Batteries Included
IMPORTANT NOTICE
Use this meter for water only. Do not use to meter fuel or chemicals.
This meter is not legal for trade applications.
The meter is very sensitive to electrical “noise” and may not operate
correctly if located near some electrical equipment.
CALIBRATION
This meter has a permanent factory calibration for measuring water. If installed and used correctly, inaccuracies of no greater than ±5% will be obtained.
INSTALLATION
This meter may be installed in-line either horizon- tally or vertically or at the end of the hose adjacent to the nozzle, if present. Installation to metal connections is not recommended. Install as follows:
- If necessary, remove nozzle from hose.
- Apply pipe sealant to all threaded connec- tions.
- Attach meter to hose with arrow on outlet port pointed in the direction of flow.
- If necessary, attach nozzle to meter.
- Hand tighten the meter at the housing ends. Do not use a wrench or similar tools to tighten the meter housing. The plastic housing could be damaged.
OPERATION
Batch and Accumulative Totals
The meter maintains two totals. The batch total may be reset to measure flow
during a single use.
The accumulative total provides continuous measurement and may not be manually
reset. The batch total is labeled as TTL1. The accumulative total is labeled
TTL2.
When the accumulative total reaches a maximum reading of 9999, it will
automatically reset to zero. Press the DISPLAY button briefly to switch
between the batch and accumulative totals.
Activate the Meter
Turn the meter ON by starting water flow or briefly pressing the DISPLAY
button. The meter will display the batch or accumulative total from last use.
Press DISPLAY briefly to display the batch total.
Hold the DISPLAY button down for three seconds to reset the batch total to
zero.
The meter is programmed to turn off automatically if not used for about one
minute.
MAINTENANCE
Proper handling and care will extend the life and service of the meter.
Turbine Rotor
The 01N Series meter is virtually maintenance- free. However, it is important
that the rotor move freely. Keep the meter clean and free of contami- nants.
If the rotor does not turn freely, apply a pene- trating lubricant on the
rotor, shaft, and bearings.
Remove any debris or deposits from the rotor using a soft brush or small
probe. Be careful not to damage the turbine rotor or supports.
CAUTION: Blowing compressed air through the turbine assembly could damage
the rotor.
Battery Replacement
The meter is powered by two AAA alkaline batteries that may be replaced while
the meter is installed. When batteries are removed or lose power, the batch
and accumulative totals reset to zero but the factory calibration is retained.
If the meter display becomes dim or blank, replace the batteries as follows:
- Remove the four Phillips-head screws from the face of the meter and lift the faceplate from the turbine.
- Remove the old batteries and clean any corrosion from the terminals.
- Install new batteries. Make sure the positive post is in the correct position.
- When the batteries are replaced, the faceplate will power ON. Check the display to ensure normal functions have resumed before assembling again.
- Reseat batteries, if necessary, and position the faceplate on the turbine housing. To avoid moisture damage, make sure the O-ring is fully seated. Tighten the four screws on the faceplate.
SPECIFICATIONS
Model: | 01N31GM |
---|---|
Unit of Measure: | Gallons |
Flowrate: | 3 to 30 GPM |
Working Pressure: | 150 PSIG |
Operating Temperature: | +14°F to +130°F |
Storage Temperature: | -40°F to +158°F |
Threads: | 1 inch NPT |
Model: | 01N31LM |
--- | --- |
Unit of Measure: | Litres |
Flowrate: | 10 to 100 LPM |
Working Pressure: | 10.3 bar |
Operating Temperature: | -10°C to +54°C |
Storage Temperature: | -40°C to +70°C |
Threads: | 1 inch NPT |
Model: 01N12LM | 01N12LM |
--- | --- |
Unit of Measure: | Litres |
Flowrate: | 10 to 100 LPM |
Working Pressure: | 10.3 bar |
Operating Temperature: – | 10°C to +54°C |
Storage Temperature: | -40°C to +70°C |
Threads: | 1 inch ISO |
GPI® TWO-YEAR LIMITED WARRANTY
Great Plains Industries, Inc. 5252 E. 36th Street North, Wichita, KS USA
67220-3205, hereby provides a limited warranty against defects in material and
workmanship on all products manufactured by Great Plains Industries, Inc. This
product includes a 2-year warranty from date of purchase as evidenced by the
original sales receipt. A 30-month warranty from product date of manufacture
will apply in cases where the original sales receipt is not available.
Reference product labeling for the warranty expiration date based on 30 months
from date of manufacture. Manufacturer’s sole obligation under the foregoing
warranties will be limited to either, at Manufacturer’s option, replacing or
repairing defective Goods (subject to limitations hereinafter provided) or
refunding the purchase price for such Goods theretofore paid by the Buyer, and
Buyer’s exclusive remedy for breach of any such warranties will be enforcement
of such obligations of Manufacturer. The warranty shall extend to the
purchaser of this product and to any person to whom such product is
transferred during the warranty period.
This warranty shall not apply if:
A. the product has been altered or modified outside the warrantor’s duly
appointed representative;
B. the product has been subjected to neglect, misuse, abuse or damage or has
been installed or operated other than in accordance with the manufacturer’s
operating instructions.
To make a claim against this warranty, or for technical assistance or repair,
contact the GPI Customer Service Department at one of the locations below.
In North or South America contact
Great Plains Industries, Inc.
5252 East 36 th St. North
Wichita, KS 67220-3205
USA
800-835-0113
www.greatplainsindustries.com
(North America)
Outside North or South America contact
GPI Australia
(Trimec Industries Pty. Ltd.)
12/7-11 Parraweena Road
Caringbah NSW 2229
Australia
+61 02 9540 4433
www.flomec.com.au
The company will step you through a product troubleshooting process to
determine appropriate corrective actions.
GREAT PLAINS INDUSTRIES, INC., EXCLUDES LIABILITY UNDER THIS WARRANTY FOR
DIRECT, INDIRECT, INCIDENTAL AND CONSEQUENTIAL DAMAGES INCURRED IN THE USE OR
LOSS OF USE OF THE PRODUCT WARRANTED HEREUN-
DER.
The company herewith expressly disclaims any warranty of merchantability or
fitness for any particular purpose other than for which it was designed.
This warranty gives you specific rights and you may also have other rights
which vary from U.S. state to U.S. state.
NOTE: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT – Part 702
(governs the resale availability of the warranty terms).great in
Wichita / Sydney
Wichita • Sydney
GREAT PLAINS INDUSTRIES
© 2021 Great Plains Industries, Inc., All Ria hts Reserved.
Great Plains Industries, Inc.
800-835-0113
greatplainsindustries.com
12/2021
920756-01 Rev. B
Documents / Resources
| GPI
01N31GM Compact 1 NPT(F) Electronic
Totalizer
[pdf] User Manual
01N31GM Compact 1 NPT F Electronic Totalizer, 01N31GM, Compact 1 NPT F
Electronic Totalizer, NPT F Electronic Totalizer, Electronic Totalizer,
Totalizer
---|---
References
- Great Plains Industries Fuel Transfer Pumps and Flow Meter Systems — GREAT PLAINS INDUSTRIES
- FLOMEC Flow Meters - Flow Meter & Instrumentation Manufacturer
- Great Plains Industries Fuel Transfer Pumps and Flow Meter Systems — GREAT PLAINS INDUSTRIES
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>