Sharkoon Rebel P30 Golf ATX 3.0 Power Supply Unit Instructions
- June 12, 2024
- sharkoon
Table of Contents
Rebel P30 Gold ATX 3.0 Power Supply Unit
Manual
Safety Instructions
This device is only to be used as a power supply unit for powering PCs and is intended exclusively for this purpose. Even when it is not being used for a long period of time, a power supply unit can still possess a high electric charge. For your own safety, be sure to follow the instructions below before using the device. The manufacturer’s guarantee will become void if damage occurs to the product as a result of improper use or non-compliance with the following safety instructions.
CAUTION!
- Only use the device with accessories approved by the manufacturer and do not unscrew or modify the device without the manufacturer’s consent. Repairs must only be carried out by authorized specialist personnel.
- Do not use the device in extreme environments. Also make sure that it always has sufficient distance to household heating appliances and radiators and other such sources of heat.
- Do not insert any objects into the openings of the device.
- The device is only intended for indoor use and within the appropriate level of humidity. Keep liquids away from the device and do not touch it with wet hands.
- Immediately disconnect the device from your household electricity supply if it comes into contact with liquid, or if smoke occurs, or if you notice any damage, for example, to the cables. Do not then use the device again.
- Only the outside of the power supply unit may be cleaned and only using a dry cloth. Before doing this, completely disconnect the device from your household electricity supply by pressing the power switch to “ ” and pulling the plug of the power cord out of your wall outlet.
Safety Standards and Protections
This power supply unit is designed for a household power voltage of 100 – 240
volts. It complies with CE, FCC, UKCA and CB safety standards and is equipped
with protection features that are designed to protect the device itself as
well as the components connected to it. The device will unexpectedly shut down
in the event of a protection function.
You should then check immediately if there is a specific cause for the
shutdown.
OPP (Over-Power Protection)
If the system demands more power than the specifications allow, the power
supply unit will switch itself off to protect the electronics from damage.
OVP (Over-Voltage Protection) / UVP (Under-Voltage Protection)
This function shuts off the power supply unit to protect the components as
soon as the internal voltage exceeds or falls below the specified limits.
SCP (Short-Circuit Protection)
Should a short circuit occur, the SCP function switches off the power supply
unit and protects the electronics from damage.
OCP (Over-Current Protection)
If the current measured on a rail exceeds a specified value, the OCP function
switches off the power supply unit to prevent damage.
OTP (Over-Temperature Protection)
If the heat level inside the power supply unit reaches a critical point, the
OTP function switches off the device to protect the electronics.
Installation
Remove the old power supply unit from the PC case
Install the power supply unit into the PC case
PLEASE NOTE!
Make sure that only the supplied modular cables are used. The use of other
cables (for example, cables from an older Sharkoon PSU series or cables from
other manufacturers) can damage the device and the peripheral hardware. Make
sure all cables are properly connected and fully inserted into the power
supply unit and the peripheral hardware.
Cooling Options
The Rebel P30 Gold is equipped with two functions for flexibly adjusting the cooling behavior, which are explained below.
Zero RPM Mode
When the Zero RPM mode is on, the fan rotation is stopped at low and medium
loads to enable silent operation. When the load on the system increases, the
fan will automatically turn on again to cool the power supply unit
sufficiently. When the Zero RPM mode is off, the fan runs continuously at low
speed to produce a constant airflow.
Fan Delay Mode
The power supply unit’s fan continues to run for 60 seconds at constant speed
after the system has been switched off. As a result, hot spots are avoided,
and remaining waste heat is transported out of the system. In addition, this
increases the service life of the installed components.
Connection Options
850 WATT
1x 20+4-pin mainboard (2x M/B)
1x 4+4-pin CPU (CPU)
2x 6+2-pin PCIe (PCI-E)
4x SATA (IDE/SATA)
1x 12VHPWR
CABLE SET
1000 WATT
1x 24-pin mainboard (2x M/B)
2x 4+4-pin/8-pin CPU (CPU)
3x 6+2-pin PCIe (PCI-E)
5x SATA (IDE/SATA)
1x 12VHPWR
CABLE SET
1300 WATT
1x 24-pin mainboard (2x M/B)
2x 4+4-pin/8-pin CPU (CPU)
4x 6+2-pin PCIe (PCI-E)
5x SATA (IDE/SATA)
1x 12VHPWR
CABLE SET
Troubleshooting
If the power supply unit is not functioning correctly, check the following points:
- Is the power cord correctly inserted into your wall outlet and the power supply unit?
- Make sure the on/off switch is in the “I” position.
- Check that the 24-pin mainboard connector and the 4+4-pin /8-pin CPU connector are correctly connected to the mainboard.
- Check if the connectors of the cables are firmly plugged into the ports and headers of the peripheral hardware.
- Pull the plug of the power cord out of your wall outlet and leave the power supply unit without power for approximately 10 minutes. This will cause a reset of the protective circuits.
If the system still fails to function, please contact support@sharkoon.com
Note
Legal Disclaimer
For potential loss of data, especially due to inappropriate handling, Sharkoon
assumes no liability.
All named products and descriptions are trademarks and/or registered
trademarks of the respective manufacturers and are accepted as protected.
As a continuing policy of product improvement at Sharkoon, the design and
specifications are subject to change without prior notice. National product
specifications may vary.
All rights reserved especially (also in extracts) for translation, reprinting,
reproduction by copying or other technical means. Infringements will lead to
compensation. All rights reserved especially in case of assignation of patent
or utility patent. Means of delivery and technical modifications reserved.
Disposal of your old products
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
**** When this crossed-out wheeled bin symbol is attached to a product, it
means the product is covered by the European Directive 2012/19/EU.
Please be informed about the local separate collection system for electrical
and electronic products. Please act according to your local rules and do not
dispose of your old products with your normal household waste. The correct
disposal of your old product will help prevent potential negative consequences
to the environment and human health.
Follow us on
Facebook
Instagram
YouTube
TikTok
**** Twitter
Sharkoon Technologies GmbH
Griininger Weg 48
35415 Pohlheim Germany
© Sharkoon Technologies 2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>