Outwell 651066 Colmar Gas Grill Instruction Manual

Outwell 651066 Colmar Gas Grill Instruction Manual

COLMAR GAS GRILL
MODEL: 651066 / H-4000

INNOVATIVE FAMILY CAMPING

COLMAR GAS GRILL

Read the Instructions before using the appliance. Keep these instructions for future reference.

1. Lid
2. Heat resistant lid handle
3. Side tables
4. Piezo ignitor
5. Drip tray
6. Chrome plated steel grill
7. Injector
8. Gas inlet connection with tap
9. Tap
10. Removable hose stud

TECHNICAL DATA

ASSEMBLY

You will need a crosshead screwdriver for the assembly.

PARTS LIST

ASSEMBLY INSTRUCTION

OPERATION

• WARNING: Use only outdoors

• Do not misuse the appliance or use it for other purposes than what it is intended for.

• Do not modify the appliance.

• Never leave the appliance unattended when lit.

• Handle the appliance with care. Make sure not to drop it.
  WARNING: Do not move the appliance during use.

• Use gloves and sturdy long barbecue tools when cooking on the gas grill.

• Hot fat may drip out at the bottom of the fire bowl. Do not light your gas grill on a surface that may be damaged by the hot fat or heat generated by the gas grill.

• Do not use an appliance which is leaking, damaged or which does not operate properly.

• WARNING: Accessible parts may be very hot. Keep young children away.

• WARNING: Turn off the gas supply at the gas cylinder after use

• Always disconnect the gas cylinder from the appliance when not in use.

• Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance.

• Any LPG cylinder not connected for use should not be stored in the vicinity of this or any other appliance.

• The appliance shall be operated on a horizontal surface

  • non likely to impair its operation
  • free from dry grass, sand etc.
  • do not place it on any combustible materials.

• The appliance shall be used away from flammable materials during use with minimum distances as shown below.

Connecting your gas grill to a gas cylinder

Please see TECHNICAL DATA table for information regarding regulator and hose. Only use a regulator complying with EN16129 and a hose complying with EN16436. The length of the hose shall not exceed 150 cm. Both regulator and hose must also comply with national regulations. Replace the hose according to national regulations. Avoid twisting the hose.

Always read the manual regarding the regulator and hose.

Never leave the regulator attached to the gas cylinder if disconnected from the gas hose.

1. To be able to use your gas grill you will need to purchase an LPG gas cylinder, a regulator and a hose. The type of gas can be butane or propane or a mixture. The regulator needs to fit the chosen gas cylinder and deliver a supply pressure of 28-30mbar if the gas is butane. 30 or 37 mbar if the gas is propane. The hose needs to fit the regulator as well as the gas grill. The gas grill can be used with either ¼” LH thread, 8mm ID or 10/11mm ID.
   a) If your hose has an internal diameter of 8 mm, push the hose over the first ribbed half of the removable hose stud. Thread the hose and stud onto the gas inlet connection.
   b) If your hose has an internal diameter of 10/11 mm, push the hose all the way over the ripped part of the removable hose stud. Thread the hose and stud onto the gas inlet connection.
   c) If your hose is equipped with a ¼“ left hand thread, thread the hose directly onto the gas inlet connection.
   The hose should be threaded hand tight plus a ¼ of a turn.
   

2. Once you have successfully connected your gas grill to a gas cylinder, position the gas cylinder at the side of your gas grill. Keep in mind that the cylinder must be kept away from heat and in a safe and upright position.

3. Attach the regulator to the gas cylinder tap correctly (refer to the instruction manual provided with the regulator).

4. Always check for leaks at all joints using soapy water.
   NEVER USE A NAKED FLAME TO CHECK FOR LEAKS.

Lighting Your Gas Grill

1. Open the lid. CAUTION: the lid must always be open when lighting the burner!
2. Close the tap (9) by turning it clockwise (in direction of the arrow next to the word ‘CLOSED’) until it stops (do not over tighten).
3. Open the regulator on the gas cylinder.
4. Turn the tap (9) a ¼ of a turn (this will release the gas into the burner) and at the same time press the piezo ignitor (4).
5. If the burner does not light after 4-5 attempts, close the tap and wait 5 minutes, then repeat steps 3 and 4.
6. Use the tap to adjust the heat.

For your safety – if you smell gas

• If there is a leak on your appliance (smell of gas), turn off the gas supply and take it outside immediately into a well-ventilated flame free location where the leak may be detected and stopped. If you wish to check for leaks on your appliance, do it outside. Do not try to detect leaks using a flame, use soapy water.
• If odour persists, stop using the appliance immediately and contact your dealer or gas supplier.

CHANGING THE GAS CYLINDER

• Turn off the unit completely. Be careful the gas appliance could be hot.
• The gas cylinder shall be changed in a well-ventilated location, preferably outside, away from any sources of ignition, such as naked flames, pilots, electric fires and away from other people.
• Follow the instructions supplied with the gas cylinder and gas regulator.
• To ensure a safe connection of a new gas cylinder to your appliance please follow the instructions in the section ‘Connecting your gas grill to a gas cylinder’.
• If gas pressure drops or the gas will not light, check if there is gas left in the cylinder. If there is gas left in the cylinder the injector on the appliance might be blocked.

CLEANING & MAINTENANCE

• Visually check the general condition of the appliance and clean it on a regular basis.
• Ensure the appliance has cooled off completely before cleaning.
• Use a wire brush, steel wool or a scouring pad to clean the griddle.
• Interior surfaces of the gas grill housing cover should also be washed with hot soapy water.
• The drip tray (5) should be cleaned regularly.
• Periodically check the burner to see that it is free from insects and spiders which may block the gas system.
• Clean the venturi tube on the burner very carefully, checking to see it is free from obstructions. We recommend that you use a pipe cleaner to clean the venturi tube area.

• Do not manipulate with any parts sealed by the manufacturer.
• WARNING: Any modification of the appliance may be dangerous.

STORAGE

• Ensure the appliance has completely cooled down.
• Disconnect the gas cylinder before you store the appliance away. Keep both the appliance and cylinder in a dry and well-ventilated place, safe from dust and dirt, and away from heat and direct sunlight.

If you are not able to rectify any fault following the abovementioned instructions, contact the dealer or Outwell Customer Service.

Outwell Customer Service
e-mail: [email protected]
Tel.: +45 70 50 59 00

outwell.com

Outwell® is a reg. trademark of Oase Outdoors
EU: Kornvej 9, DK-7323 Give, Denmark
UK: One Glass Wharf, Bristol, BS2 0ZX

P.I.N. 8504DN-0064 P.I.N. 2531/CT/0001

© 09/2022 Oase Outdoors ApS. Made in China

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>