SELKA Electro Smart L WW ELECTRO L 78×50 Electric Desk Instruction Manual
- June 4, 2024
- SELKA
Table of Contents
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations! You chose a SELKA product! Hope you will enjoy using it as
much as we enjoyed making it!
PACKAGE INCLUDES
An 8 pl M6x12mm* head screw
B 2 pl M8x16 mm thread pin
C 2 kpl M5x25mm* head screw
D 8 kpl M6x16 mm countersunk screw
E 1 kpl 3 mm hex key
F 1 kpl 4 mm hex key
G 2 kpl cable holder
with oak table top 16 mm
** with oak table top 30 mm
TABLE COMPONENTS:
- Tabletop
- Table pedestal
- Table leg with power cords (connect two cords)
- Top plate
- Control panel
- Power cord the ELECTRO SMART model comes with Lithium Ion Battery and a charger
- Electro Smart top plate
- Electro Smart charger
Note the leg orientation
Attach the top plate to the table leg with the D countersunk screws by using the F hex key.| Protect the tabletop with cardboard and place the top plate on top of it.
Do not use a power drill
Place the A head screws by hand and then tighten them carefully with the F hex
key.| Attach the control panel with the C head screws using the E hex key.
Fasten the B thread pins to the table leg hex slot outward by turning them a few rounds.| Turn the table sideways and attach the pedestal with D countersunk screws.
Connect the cables according to the picture.
Attach the G cable holders to the bottom of the tabletop.| Turn the table upright and you’re finished!
ADJUSTING THE HEIGHT
Adjust the height of the table by gently pushing the entire control panel, either up or down. Press until the table is at your preferred height.
See video instructions: selkastore.eu/ pages/how- ouse-electro| Electro
troubleshooting codes:
---|---
|
---|---
https://qrgo.page.link/VNXMG|
https://cdn.shopify.com/s/files/1/0505/1757/3822/files/ELECTRO_troubleshooting_guide.pdf?v=1623406638
CHARGING THE ELECTRO SMART BATTERY:
The Battery can be charged either via the Control Box or via the Battery Box.
You can also charge the battery removed from the table. To remove the battery,
press the clip on the end of the battery and slide the battery out.
Charging via Control Box
Connect the main cable to the control box and plug the cable into the mains.
When the charging starts, the battery beeps twice. After approximately five
hours, the battery is fully charged, and the LED light bars turn off.
Charging via Battery
Disconnect the DC cable from the battery. Connect the DC charging cable to the
battery and plug the cable into the mains. When the charging starts, the
battery beeps twice. During charging, the LED light bars indicate the actual
capacity. When the charging is complete the LED light bars turn off. Charging
will not start if the capacity is above 75 %.
Capacity
Turn on the light for a few seconds by pressing the small black button below
the LED light bars. The four LED light bars to indicate the actual capacity.
| Capacity
0 to 5 %
5 to 25 %
25 to 50 %
50 to 75 %
75 to 100 %| Lit up LED light bars
None
LED1
LED1 and LED2
LED1, LED2, and LED3
LED1, LED2, LED3, and LED4
---|---|---
Notes
When the capacity is below 25 %, the audio alarm sounds once each time the
battery is activated.
The battery turns off to protect itself when the capacity is approx. 5 %.
Below 5 % capacity, the audio alarm sounds once each time the battery is
activated. No LED light bars can be lit.
Read the entire battery user manual here:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>