myGEKOgear SOLARST Wireless Backup Camera User Guide

SOLARST
Solar Wireless Back Up Camera
Quick User Guide

INTRODUCTION

Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. The installation instructions do not apply to all types of vehicles, and are written as guidelines to assist in installing the system.
Consult an experienced technician if you are not comfortable installing the product.
BEFORE using the myGEKOgear SOLARST, please read the safety information provided in this user manual. ALWAYS use the product as outlined in this user manual.
Please make sure to read and understand all local laws and regulations regarding cameras and their use in a vehicle. Laws vary by state.

WHAT’S IN THE BOX

1. Solar Powered Wireless Backup Camera
2. 4.3″ Dash Color Monitor with 3M Mounting Holder
3. Suction Holder (Optional)
4. 12/24VPower Adapter for Monitor
5. USB – DC Cable for Charge License Plate Backup Camera Power
6. User Manual
7. 4 x Mounting Screw
8. lx Screw & Tool

PRODUCT SPECIFICATIONS

1. Frequency: 2.4GHz
2. Operating Voltage: Monitor – DC 12V/24V, Backup Cam – DC 5V
3. Operating Temperature: 14-140F (-100C-600C)
4. Camera Water Resistance: IP67 Rating
5. Battery Capacity: 2100mAh
6. Maximum Signal Range:50M Max (without interference or obstruction)

INSTALLATION GUIDE

1. Place the dash monitor on to the dashboard or windshield and adjust to your desired position and remove the sticker under the bottom.
2. Place the monitor in your desired position, using either windshield mount or 3M sticker mount.
3. Remove the dash monitor protective overlay.
4. To power the dash Monitor: Take the 12V/24V power adapter and plug into 12V/24V power port in your car .
5. Now, the dash monitor is ready to be activated by pressing the monitor “Touch FOR REVIEW” wake-up button .

Notice :

1. When monitor is power on and working command will send to camera , after the camera receive this signal will be enter into standby status at once and send image video to the monitor within 150MS .
2. When in bad signal situation , the monitor and camera will disconnect and monitor will show a image on screen in a short time which means” signal is connecting ” , usually within 3 seconds will be recover to working status . If over 10 seconds no signal then it will power off automatically then it need touch the”Touch FOR REVIEW ” wake-up button by hand to make it normal working .
   Warning: Many vehicles provide constant power to the 12V outlet. If your outlet provides constant power, please remember to unplug the dash monitor when not in use to avoid draining the vehicle battery.
   NOTE: We recommend to fully charge your backup camera overnight before use

SOLARST INTRODUCTION AND INSTALLATION

Introduction

1. Solar Panel
2. Mounting Tab
3. Camera
4. Charging Interface
5. LED Indicator Light for Charging

Introduction (3 figures)

1. Unscrew your license plate.
2. Secure the solar wireless backup camera and license plate with screws back onto the rear of your vehicle.
3. Power on the Monitor with the 12V/24V adapter. You can see the parking view when you wake up the SOLARST camera by touching the monitor’s wake-up button.

• Please follow your local laws and regulations regarding constant monitoring while driving. It isrecommended that you glance at the image only when in reverse, and use as an aid. Do not relysolely on the camera view to back up. * By using the “Touch FOR REVIEW ” wake-up button on the monitor, the image can be shut off while driving. Please remember to turn back on once the vehicle is stopped and ready to reverse.

SETTINGS AND OPERATION

MENU Operation

1. Main Menu While the monitor is showing the rear image, short press the middle button [MENU/OKI to enter the main menu interface, and 5 options are available (Pairing, Image Parameters, Image Mirror, Parking Guideline, Time Setting).
   Icon| | | | |
   ---|---|---|---|---|---
   Function| Pairing| Image Parameter| Mirror/Original
   Camera| Reversing line| Time Setting
   Operation| Default setting| Adjust the brightness contrast tote Operation delais receive Image Parameter irk| Set with PAirrafOriginal image. Operation details reference MirrorfOriginal Camera contents| Chaise different reversing lee setting far different car| Seiecr ‘Arne setting’ and !cog press [Menu 10Xlker. Press IADD1 orgXCI key to select •teking time.

2. Image Parameter
While the monitor is showing the backup camera image , press “MENU” once to enter main menu then press up and down key to choose the Image Parameter ,press and hold MENU button again to enter into the three image (Brightness/Contract/Color) interface to start setting .
1). Brightness setting Select Brightness icon will be grey color , long press to highlight with yellow color and press up and down key to adjust as below and press MENU button three times to exit to memorize the last operation .
2). Contract setting Select Contract icon will be grey color , long press to highlight with yellow color and press up and down key to adjust as below and press MENU button three times to exit to memorize the last operation.
3). Color setting Select Color icon will be grey color , long press to highlight with yellow color and press up and down key to adjust as below and press MENU button three times to exit to memorize the last operation .
3. Mirror/Original Camera
While the monitor is showing the backup camera image , press “MENU” once to enter main menu then press up and down key to choose g0 the Mirror / Original Camera , press and hold MENU button again to see to set Mirror camera ( default setting ) or Original camera and press MENU button two times to exit to memorize the last operation .
4. Reversing Line
While the monitor is showing the backup camera image , press °MENU” once to enter main menu then press up and down key to choose MO the Reversing line ,press and hold MENU button to see thereversingline and press up and down key to choose the suitable reversing line and press MENU button two times to exit to memorize the last operation.
NOTICE : When the monitor is working it will show the backup camera image with Reversing line , if you no need then press “Down” button one time the Reversing line will disappear and press again it will appear . Time Setting
Select 0 and tong press [MENU/OK] key, press [ADD] or [DEC] key to select working time.
NOTICE : The Screen Display Time Setting : The display will stay on for 60 seconds (Default) , 45 seconds or 30 seconds . Please choose the best time to fit your needs .

DISPLAY ICONON SCREEN

1. Signal strength
2. Solar charging
3. Camera battery
   Low Battery Prompt: When built in battery power is low it will automatically show Low Battery words on the screen , then you have to charge the battery with USB-DC cable, otherwise the camera and the monitor will not work .

CHARGING INFORMATION

1. When the monitor is charging there is beep voice to reminder without indicator light on it . When touching the ” Touch for Review ” button power on or power off , the RED light on back camera shell will flash quickly.
2. When Use the USB-DC cable to charge for the battery, the RED light will be bright all the time till it full charged then the light will off.
3. When the solar panel is charging , there is Solar Charging icon on the screen will be appear. NOTICE: If the products parking in the house for long time ,usually it need charge one time within 6 month , otherwise the battery will be easy to broken.

SAFETY INFORMATION

WARNING: A failure to read and follow these warnings and instructions may result in a serious accident, including damaged property or a serious injury, including loss of life.

1. The SOLARST camera is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. However, you, the driver, must use it safely and properly. Use of the SOLARST camera is not a substitute for safe, proper and legal driving.
2. Never back up while looking only at the screen. You should always check behind and around the vehicle when backing up just as you would if the vehicle did not have the SOLARST camera. Always make sure your intended path is clear. If you back up while looking only at the monitor, you may hit a vehicle, pedestrian, bicyclist, child, pet or other object resulting in injury or death. Always back up slowly.
3. Never depend on the SOLARST camera entirely when backing up. The image on the screen is different from actual conditions. Objects viewed in the rear-view monitor differ from actual distance because a wide-angle lens is used. Objects in the rear-view monitor will appear visually opposite than when viewed in the rear view and outside mirrors. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.
4. The SOLARST camera “night vision” feature that is high performance brightness with colorful image is an aid to a driver but is limited. Always use your own eyes to confirm the vehicle’s surroundings, as the displayed image may be faint or dark, distorted, or not entirely visible. Always check behind and all around the vehicle visually SOLARST camera is limited. The SOLARST camera does not display objects that are close to or below the bumper, underneath the vehicle, or objects out of the camera’s field of view. The area displayed on the screen may vary according to vehicle orientation or road conditions.
5. Be sure to check the camera’s position and mounting angle before each use.
6. Make sure the trunk, hatch, or backdoor is completely and securely closed when backing up.
   • If the back of the vehicle is hit, the position and mounting angle of the SOLARST camera may change.
   • When washing the vehicle with high pressure water, be sure not to spray it around the SOLARST camera. Otherwise, water may enter the camera unit causing water condensation on the lens causing a malfunction, fire, or an electric shock.
   • Do not strike the SOLARST camera. It is a precision instrument. Otherwise, it may malfunction or cause damage resulting in a fire or an electric shock.
   • This product will only provide images of items that are within the field of view of the SOLARST. Thus, it is imperative that the SOLARST camera should be kept clean and unobstructed; should be mounted so that its field of view includes the entire area behind your vehicle.
   • Adhere to all applicable traffic laws and motor vehicle regulations applicable to the device.
   • Consult local laws and regulations for any restrictions on installation or use.
   • Never allow children to play with the device. Small parts may be a choking hazard.
   • If you replace the tires, the area displayed on the monitor may change and you may need to adjust the camera.
   • The SOLARST camera has a water-resistant construction. Do not detach, disassemble or modify it. This may cause incorrect operation.
   • Do not submerge the SOLARST camera in water, this can cause internal damage to the camera.
   • If the temperature changes rapidly, such as when hot water is poured on the vehicle in cold weather, the system may not operate normally. The digital camera can withstand the effects of rain, snow, and inclement weather.
   • When strong light directly enters a camera, objects may not be displayed clearly.
   • The screen may flicker under fluorescent light.
   • The colors of objects on the rear-view monitor may differ somewhat from those of the actual object.
   • If dirt, rain or snow attaches to the camera, the monitor may not clearly display objects. If water droplets, snow or mud adhere to the camera lens, rinse with water and wipe with a dry cloth.
   • Do not use alcohol, benzene or thinner to clean the camera. This will cause discoloration. To clean the camera, wipe with a clean cloth dampened with mild cleaner diluted with water and then wipe with a dry cloth.
   • Will work up to 50M.
   • ALWAYS engage Parking/Emergency/Hand Brakes of the vehicle when testing the system.

SAFETY AROUND AND BEHIND OTHER VEHICLES

Using a solar powered camera is not enough to completely overcome a vehicle’s blind spot. Many preventable injuries and deaths occur in driveways or parking lots when drivers do not see children, pets, or others near their vehicles. Here are a few safety tips that will help you to avoid a back-over accident: Walk completely around your vehicle before getting in. Check for kids, toys, and pets before entering the vehicle and starting the engine. Know where children are. Have children stand in a place where they are in full view. Be aware of young children. Young children are small and hard to see. Parents, care givers and all adults need to be vigilant in supervising children, especially when children are in the yard, driveway or parking lot playing near parked cars. Roll down your window so you will be able to hear what is happening outside your vehicle. Owners of SUVs, trucks, and vans need to take extra care to avoid hitting or running over a child. Teach children to move away from a vehicle whenever it is started.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>