ORREN ELLIS W007156331 LED Bathroom Mirror Instruction Manual

ORREN ELLIS W007156331 LED Bathroom Mirror

Product Information: LED BATHROOM MIRROR

The LED Bathroom Mirror is a high-quality mirror designed for installation in bathrooms. It features LED lighting for enhanced visibility and a sleek design that complements any bathroom decor.

Electrical Safety Instructions

Installation of the LED Bathroom Mirror should be done by a qualified and registered electrician to ensure safety. The following electrical safety guidelines should be followed:

• Do not attempt to install the mirror yourself if you are not a qualified electrician.
• Ensure that the power is turned off before starting the installation process.
• Follow all local electrical codes and regulations.

Installation Procedure

To install the LED Bathroom Mirror, follow these steps:

1. Make sure the power is turned off.
2. Position the mirror in the desired location on the wall.
3. Mark the spots where you will need to drill holes for mounting.
4. Drill the holes according to the marked spots.
5. Securely mount the mirror on the wall using appropriate screws and anchors.
6. Connect the electrical wiring according to the provided instructions or consult a qualified electrician for assistance.
7. Turn on the power and test the functionality of the LED lights.

Installation Care & Safety

When installing the LED Bathroom Mirror, it is important to take care and follow these safety precautions:

• Avoid striking the glass components with hard or pointed items.
• Avoid placing very hot or very cold items against or in close proximity to the glass surfaces. If necessary, use an adequately thick insulation material to prevent direct contact with the glass.
• Comply with all applicable safety regulations and guidelines.

By following these instructions and safety precautions, you can safely install and enjoy the LED Bathroom Mirror in your bathroom.

| ON &OFF/Dimmer Switch

Press the button  , the button will change from red to blue, and the light in ON. Press the button  again, the button will change from blue to red, and the light is OFF.

Press the button for 3 seconds, the light brightness will be adjusted from 100% to 10%.

Press the button for another 3 seconds, the light brightness will be adjusted from 10% to 100%.

---|---

| ****

Adjustable Color Temperature

Adjustable color temperature could be switched among cold white light (6500K), natural light (4500K) and warm white light(3500K).

| ****

Defogger Function Swich

Press the button , the buton will change from red to blue, and the anti-fog iS ON.

Press the button again, the button will change from blue to red, and the anti- fog is OFF.

Our mirror controller has the memory function which can memorize the final status of:

1. The light ON or OFF.

2. The light brightness.

3. The light temperature.

4. The anti-fog ON or OFF.

Electrical Safety Instructions

INSTALLATION has to be made by a qualfed/registered electrician.

1. Read this instruction carefully and refer back to them during installaton to ensure that your product is fitted safely and correctly.
2. Always switch off the electrical supply at the mains during installation and maintenance.lt is recom-mended that the fuse is withdrawn or the circuit breaker is switched off for the necessary circuit before installation.
3. This product is only suitable for permanent instalation. DO NOT connect to a trailing plug and socket outlet Altough this product has an Ingress Protection rating of IP44 it is only suitable fir indoor use. DO NOT attach the product to surfaces that are damp or otherwise electrically conductive.

Installation Care & Safety

1. Wear suitable eye protection when drilling.

2. Take care when using power tools near water the use of a residual current device (RCD) is advised.

3. Beware of hidden cables or pipes.Take care if drilling on tiled surfaces in case the drill slips. A piece of masking tape applied to the wall before marking out the fixing holes will stop the drill from wandering.

4. This product should be positioned well away from curtains and other fabrics.Never cover the mirror This product is heated.
   We recommend that it is turned off after use and should never be left on for prolonged periods of time.
   WHEN THE MIRROR MUST BE CLEANED, IT IS NECESSARY TO SWITCH IT OFF FIRSTLY!

   • DO NOT strike glass components with hard or pointed items.
   • DO NOT place very hot or very cold items against or in clase proximity to glass surfaces unless an adequately thick insulation material isused to prevent such items coming in contact with the glass.

COMPLIANCE

All electronic components used in this products are UL listed.
Please read follow installation proce-dure Before install

Installation Procedure

Before starting your installation

1. The wall surface must be of suitable strength and construction
2. The main electricity supply has been power-off

STEP 1:
Measure the distance(X) between the key-hole centers on the backof the mirror (can behang vertically or horizontally).
Draw a horizontal line on the wall according to the height you want hang the mirror. Mark the dril positions on the horizontal line using dimension(X) taken from step 1. Ensure the hole positions are horizontal by using a spirit level.
Accurately mark the 2 hole positions with a pencil, drills and fit the wall plugs.

NOTE:
The wall plugs supplied are only suitable for solid stone / brick walls.
For any other wall types,please go to stores to buy the correct plugs & screws after checking.

STEP 2:

1. Make the electrical connection from the mirror to the mains supply. Use the connection wire found at the rear of the mirror to make the necessary connections.
2. Insert the wall screws supplied into the wall plugs. Leave approximately 5-10mm of the screw standing proud of the walL. Mount the mirror onto the screws fitted to the wall Ensure mirror is securely mounted.
3. To remove the mirror, the mirror should first be lifted and then pulled away from the wall.

Wiring
This product is designed and manufactured in class II category.no need earth connection.
The product need hardwired with the supply cable lead from the wall.

Light & Control
The integrated LED light source and system are not support to replaced by consumers.
Please DO NOT change by yourself.
The lights(and defogger) are controlled by touch sensor on mirror surface to turn on/off and adjust brightness and color temperatures.
Keeping the mirror lights on, then you also could control it on&off by wall switch, if connect with it. The last working condtion before switching off would be kept while turn on again, either brightness level or color temperature.

TOOLS

Please prepare below tools before assembly .

Locate and mark centres using mirror assembly as template

INSTALLATION SPECIFICATIONS

1. 120V hardwire electrical connection; junction box required. This mirror was designed and produced according to CLASS II level （Double Insulation), no need ground wire connection. Ensure all connection are tight in place.
2. Mirror should be mounted to wall studs; wall bracket provided.
3. Controlled by capacitive touch button on fixture or non-dimming on/off wall switch.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>