MARCARD N300 WiFi Extender User Guide

MARCARD N300 WiFi Extender

Product Information

The product is a Wi-Fi Extender designed to boost the range and coverage of your existing Wi-Fi network. It extends the wireless signal to areas in your home or office that have weak or no Wi-Fi coverage.

Product Specifications

• Dimensions: 1 25mm x 75mm
• Power : Connects to a power outlet
• Switch: ON/OFF switch located on the left side of the device
• Reset Button: Used to activate the Extender and initiate a reboot

Macard Phone setup

View full video setup tutorial at: themacard.com/guide

Product Usage Instructions

• Step 1: Plug the Extender into a power outlet near your existing Wi-Fi Router.
  Turn ON the Extender by flicking the ON/OFF switch upward. The switch is located on the left side of the device.

• Step 2: Activate the Extender by pressing and holding the RESET button for 15 seconds. The Extender will reboot within 30 seconds.

• Step 3: Open the settings on your mobile device and disable mobile data. This step ensures that your device connects to the Extender instead of relying on mobile data.

• Step 4 : Go to your Phone settings Open Wi-Fi, and turn it ON. Search for the network name ”Wi-Fi Extender”and click on it to connect.
  NOTE: To open the setup page, you MUST connect to the WI-Fl Extende内 network一[extende?s default name]. You will connect the Extender to your primary Wi-Fi network during a later step.

• Steps 5: Open a web browser and input: go.macard.online

Note: For optimal performance, place the Extender in an area where it can receive a strong Wi-Fi signal from your existing router. This will help maximize the coverage and range extension provided by the Extender.

Step 5: Click “LOGIN” and wait 10 seconds. The system scans all networks.

Step 7: Click on the name of the existing Wi-Fi Network you want to extend, e.g., Home Wi-Fi.
Steps 8: Type your Wi-Fi password into the Password box. Click the “Save Setting” button.

NOTE : Enter the password you use to connect to your main Wi-Fi router. Double-check the password and remember that it is case-sensitive.
Once you ‘1./ complete the steps, your Extender reboots automatically Place the Extender halfway between your Wi-Fi Router and the area with poor signal coverage. The Extender’s default name is your [Wi-Fi name – Plus], e.g.. HOME WI-FI – Plus. The password remains the same as the existing Wi-Fi Router’s password.

• How do I reset the Extender?
  Press the “RESET” button for 15 seconds. The Extender will reboot within
  50 seconds. You can setup the Extender again.

• How far should the Extender be from the router?
  The Extender should be halfway between the Wi-Fi Router and the area with poor
  signal coverage. The Extender must receive a good signal from the Wi-Fi Router.

• Should I connect the ethernet cable from the Wi-Fi Router to the Extender?
  No, you should only connect the network cable from the Extender to a computer.

• Does the Extender increase my internet speed?
  No, it increases the range of your Wi-Fi Network.

• Does the Extender work with 5GHz?
  No, the Extender only operates in the 2.4GHz band.

Need help?
We’re here for you!
IF YOU HAVE ANY ISSUES WITH THE DEVICE, PLEASE CONTACT US FOR ASSISTANCE BEFORE OPENING A RETURN REQUESY

WARNING:

• Unplug the dence in the event of a thunderstorn to prevent darr age.
• Keep the device away from any heat source and moke sure the device is we ventilated

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limit are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body

Macard PC Setup

View full video setup tutorial at:themacard.com/guide

Step 1: Plug the Extender into a power outlet near your existing Wi-Fi Router. Tum ON the Extender with an upward flick of the “ON/OFF” switch. The switch is on the left side of the device

Step 2: Activate the Extender by pressing the “RESET” button for 15 seconds. The Extender will reboot within 30 seconds

Step 3: If you have a PC with Wi-Fi settings: Go to your PC Wi-Fi settings. Open Wi-Fi, and turn it ON. Search for the network name “Wi-Fi Extender” and click on it to connect

OR

If you have a PC without Wi-Fi settings: Use the included Wi-Fi network cable to connect your Extender to the computer.

NOTE: T o open the setup page, you MUST connect to the Wi-Fi Extender’s network-[extender’s default name]. You will connect the Extender to your primary Wi-Fi network during a later step.

Step 4

Open a web browser and input: go.macard.online

Step 5: Click “LOGIN” and wait 10 seconds. The system scans all networks

NOTE: If after login, the Extender opens a page with all settings, please click the “REPEATER” mode, and the Extender will start scanning networks

Step 6: Click on the name of the Wi-Fi network you want to extend, e.g., Horne WI-Fl.

Step 7: Type your Wi-Fi password into the Password box Click the “Save Setting” button

NOTE: Enter the password you use to connect to your main Wi-Fi router. Double-check the password and remember that it is race_concitive

Once you complete the steps, your Extender reboots automatically.
Place the Extender halfway between your Wi-Fi Router and the area with poor signal coverage.

The Extender’s default name is your [WI-Fi name – Plus], e.g., HOME WI-FI – Plus.
The password remains the same as the existing WI-Fi Router’s password

Need help?
We’re here for you!

• IF YOU HAVE ANY ISSUES
• WITH THE DEVICE,
• PLEASE CONTACT US
• FOR ASSISTANCE BEFORE
• OPENING A RETURN REQUESY

WARNING

1. Unplug the device in the event of a thunderstorin to prevent damage.
2. Keep the device away from any heat source and make sure the device is well ventilated

ISED Statement
This device contains licence-exempt transmitters receivers) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   The digital apparatus complies with Canadian CAN ICES-3 (B)NmB-3(B).

Online support
Available Mon-Sun 9:00 am – 9:00 pm (CST)
care@themacard.com

Available 24/7
themacard.com/help

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>