robbe SCIROCCO XL 4 5M PNP Full-Grp High Performance Glider Instruction Manual

robbe SCIROCCO XL 4 5M PNP Full-Grp High Performance Glider

Product Information

• Product Name: Modellsport
  • PNP-Version Nr.: 2675 ARF-Version Nr.: 2674
  • PNP-Version Nr.: 2669 ARF-Version Nr.: 2668
  • PNP-Version Nr.: 2671 ARF-Version Nr.: 2670
  • PNP-Version Nr.: 2673 ARF-Version Nr.: 2672
• Website: www.robbe.com
• Version: V3_08/2022
• Country of Origin: Made in China

Product Usage Instructions

1. Assembling the Model:
   • Before starting the assembly, carefully read the instruction manual.
   • Follow the provided instructions step by step for proper assembly.
   • Use fine sandpaper or a file to remove any rough edges or imperfections from the parts.
   • Ensure the model is securely assembled before proceeding to the next steps.
2. Safety Instructions for Model Operation:
   • Read and understand the safety instructions provided in the manual.
   • Follow all safety precautions while operating the model.
   • Be aware of potential risks and take necessary precautions to avoid injuries.
   • Pay attention to the safety instructions for controllers and rechargeable batteries.
3. Insurance and Warranty:
   • Ground-based models are usually covered by personal liability insurance.
   • Additional insurance or extension may be required for aircraft models.
   • Check your insurance policy (private liability) and take out suitable insurance if necessary.
   • The product comes with a warranty. Refer to the warranty terms and conditions for more details.
4. Disposal:
   • The symbol on the product indicates that small electrical and electronic devices should be disposed of separately from household refuse.
   • Dispose of the product at your local municipal collection point or recycling center.
   • This disposal guideline applies to all countries of the European Union and other European countries with a separate collection system.

Note: For detailed flight instructions and specific component usage, please refer to the complete user manual available on the official website of Robbe Modellsport (www.robbe.com). Please ensure you follow all safety guidelines and instructions provided in the user manual for safe and proper usage of the Modellsport product.

GENERAL INFORMATION

• The model is designed for the components specified by us. Unless otherwise stated, servos and other electronic components are designed for standard supply voltage. Recommended cell count for Lipo batteries also refers to standard Lipos voltage of 3.7V per cell. If you use other servos, a different motor and controller, batteries, or propellers, please make sure they fit first. In the event of deviations, corrections and adjustments must be made by yourself.
• Before starting construction, always put the servos into neutral. To do this, switch on the remote control and move the joysticks and trim buttons (save the one for the throttle) to the middle position. Connect the servos to the corresponding outputs of the receiver and supply them with a suitable power source. Please observe the connection diagram and the operating instructions of the remote control system manufacturer.
• Do not leave your model in the blazing sun or in your vehicle for long periods of time. Too high temperatures can lead to deformation/distortion of plastic parts or blistering of covering foils.
• Before the first flight, check the wing symmetry, tail unit and fuselage. All parts of the model should have the same spacing from the left and right wing or tail plane to the center of the fuselage or the same angle.
• If necessary, rebalance the propellers if vibrations are noticeable when the motor is running up.
• Bubble formation in the covering foils normal to a certain extent due to temperature and humidity differences and can be easily eliminated with a foil iron or hairdryer.
• For models in shell construction („full GFRP/CFRP“), burrs may occur at the seams due to the production process. Carefully remove them with fine sandpaper or a file.

GENERAL SAFETY INFORMATION

• Be sure to read the safety instructions carefully before operating your model.

• Always follow the procedures and settings recommended in the instructions.

• If you are using remote-controlled model aircraft, helicopters, cars or ships for the first time, we recommend that you ask an experienced model pilot for help.

• Remote-controlled models are not toys in the usual sense and may only be used and operated by young people under 14 years of age under the supervision of adults.

• Their construction and operation requires technical understanding, careful craftsmanship and safety-conscious behavior.

• Mistakes or negligence during construction, flying or driving can result in considerable damage to property or personal injury.

• Since the manufacturer and seller have no influence on the proper construction/assembly and operation of the models, these risks are expressly pointed out and any liability is excluded.
  Propellers on aircraft and all moving parts in general pose a constant risk of injury. Avoid touching such parts at all costs.
  Note that motors and controllers can reach high temperatures during operation. Avoid touching such parts at all costs.

• Never stay in the danger area of rotating parts with electric motors with connected drive battery.

• Overcharging or incorrect charging can cause the batteries to explode. Make sure the polarity is correct.

• Protect your equipment and Models from dust, dirt and moisture. Do not expose the equipment to excessive heat, cold or vibration.

• Use only recommended chargers and charge your batteries only up to the specified charging time. Always check your equipment for damage and replace defects with original spare parts.

• Do not use equipment that has been damaged or got wet due to a fall, even if it is dry again! Either have it checked by your specialist dealer or in the Robbe Service or have it replaced. Hidden faults can occur due to wetness or a crash, which lead to a functional failure after a short operating time.

• Only the components and accessories recommended by us may be used.

• Do not make any changes to the remote control which are not described in these instructions.

SAFETY NOTE FOR MODEL OPERATION

Attention, danger of injury!

• Always keep a safe distance from your model aircraft.
• Never fly over spectators, other pilots or yourself.
• Always perform flight figures in a direction away from the pilot or spectators.
• Never endanger people or animals.
• Never fly near power lines or residential areas.
• Do not operate your model near locks or public shipping.
• Do not operate your model on public roads, motorways, paths and squares, etc., but only in appro-ved locations.
• Do not operate the model in thunderstorms.
• Before each flight, check your remote control system for sufficient function and range.
• After flying, remove all batteries from the model.

Do not „aim“ the transmitter antenna at the model during operation. In this direction, the transmitter has the lowest radiation. The best position of the antenna is to the side of the model.
Use of devices with image and/or sound recording function:
If you equip your model with a video or image recording device (e.g. FPV cameras, action scams etc.) or the model is already equipped with such a device at the factory, please note that you could violate the privacy of one or more persons by using the recording function. An overflight or driving on private ground without the appropriate permission of the owner or approaching private ground can also be regarded as an invasion of privacy. You, as the operator of the model, are solely and fully responsible for your actions.
In particular, all applicable legal requirements must be observed, which can be found in the roof associations or the relevant authorities. Failure to comply can result in substantial penalties.

SAFETY INSTRUCTIONS FOR CONTROLLERS

• Observe the technical data of the controller.
• Observe the polarity of all connection cables.
• Avoid short circuits at all costs.
• Install or package the regulator so that it cannot come into contact with grease, oil or water.
• Effective interference suppression measures on the electric motor with, for example, interference suppression capacitors
• Ensure adequate air circulation.
• Never reach into the turning circle of the propeller during start-up Risk of injury

Dealing with model aircraft and vehicles requires technical understanding and a high level of safety awareness. Incorrect assembly, incorrect adjustment, improper use or the like can lead to personal injury or damage to property. Sudden starting of connected motors can lead to injuries due to rotating parts such as propellers. Always stay away from these rotating parts when the power source is connected. All drive components should be safely and securely mounted during a function test. Use is only permitted within the scope of the technical specification and only for RC hobby applications. Be-fore use, check that the speed controller is compatible with your drive motor or power source. Never operate the speed controller (correct speed controller) with external power supply units. Speed controllers should always be protected from dust, moisture, vibration and other mechanical stresses. Even splash-proof or waterproof equipment should not be permanently exposed to moisture or moisture. High operating temperatures or poor cooling should be avoided. The recommended temperature range should be approximately between -5°C and +50°C. Ensure proper connection and do not cause reverse polarity which would permanently damage the speed controller. Never disconnect the device from the motor or battery during operation. Use high-quality plug systems with sufficient load capacity. Avoid strong bending or tensile stress on the connecting cables. After termination of flight or driving operation, disconnect the battery to prevent deep discharge of the battery. This would cause permanent damage. For the BEC version of the controller, check that the BEC power of the device is sufficient for the servos used. Speed controllers should be installed as far away as possible from other remote control components. We recommend carrying out a range test before operation. We recom- mend regular checking of the controller for function and externally visible damage. Do not continue operating the controller if you notice any damage. The connection cables must not be extended. This can lead to unwanted malfunctions. Despite existing safety and protective devices of the device, damage may occur which is not covered by warranty. The warranty also expires if changes are made to the device.

Important information:
The receiver system is powered by the built-in BEC system of the controller.
For commissioning, always move the throttle stick to the „Motor off“ position and switch on the trans-mitter. Only then connect the battery. To switch off always disconnect the connection battery motor controller, first then turn off the transmitter. During the functional test, move the servos of the rudders to neutral position with the remote control (stick and trimming lever on the transmitter to the middle positi-on). Please make sure to leave the throttle stick in the lowest position so that the engine does not start. For all work on to the parts of the remote control, motor or controller, follow the instructions supplied with the units. Also read the instructions of the battery and the charger carefully before commissioning. Check the engine mounting bolts in the fuselage regularly for tightness.

WARRANTY

Our articles are equipped with the legally required 24 months warranty. Should you wish to assert a justified warranty claim, always contact your dealer, who is responsible for the warranty and the processing. During this time, any functional defects that may occur, as well as manufacturing or other problems, will be rectified.
Material defects corrected by us free of charge. Further claims, e.g. for consequential damages, are excluded.
The transport to us must be free, the return transport to you is also free. Freight collect shipments can-not be accepted. We cannot accept liability for transport damage and loss of your consignment. We recommend appropriate insurance.

To process your warranty claims, the following requirements must be met:

• Attach the proof of purchase (receipt) to your shipment.
• The units have been operated in accordance with the operating instructions.
• Only recommended power sources and original robbe accessories have been used.
• There is no moisture damage, external interference, reverse polarity, overloading or mechanical damage.
• Attach relevant information for finding the fault or defect.

DISCLAIMER

Robbe Modellsport cannot monitor compliance with the assembly and operating instructions or the conditions and methods for installation, operation, use and maintenance of the model components. Therefore, we accept no liability for losses, damage or costs arising from or in any way connected with incorrect use and operation. To the extent permitted by law, the obligation to pay damages, irrespective of the legal grounds, shall be limited directly to the invoice value of the claims arising from the event causing the damage.

INSURANCE

Ground-based models are usually covered by personal liability insurance. Additional insurance or extension is required for aircraft models. Check your insurance policy (private liability) and take out suitable insurance if necessary.

CONFORMITY

Robbe Modellsport hereby declares that this device complies with the essential requirements and other relevant regulations of the corresponding CE directives. The original declaration of conformity can be found on the Internet at www.robbe.com, in the detailed product view of the respective device description or on request. This product can be operated in all EU countries.

DISPOSAL

This symbol means that small electrical and electronic devices must be dis- posed of at the end of their useful life, separated from the household refuse. Dispose of the device at your local municipal collection point or recycling centre. This applies to all countries of the European Union and other European countries with a separate collection system.

BOX CONTENT

TECHNICAL DATA

SCIROCCO XS: 2674 / 2675

SCIROCCO S: 2668 / 2669

SCIROCCO L: 2670 / 2671

SCIROCCO XL: 2672 / 2673

FUSELAGE

First install the motor on the motor mount by two M3x6 Allen screws.

Draw the positions of the servo board and battery board supports in the fuselage. Sand these locations thoroughly and clean the surface.

The servo board should be centered under the fuselage cutout, about 28mm below the wing root.

The battery board is fitted centrally under the cabin cut-out. Note: only the support bridges are glued, NOT the battery board itself.

Glue both parts into the fuselage with 10-min. epoxy.

The servos must be placed into the designated wooden frame by already put in neutral position. The servo arm has to be fixed in 90° position.

Make a fuselage harness from four servo wires and a green MPX connector. The positive and negative terminals can be combined. This will leave four pins for the impulse lines.

The rudder and elevator linkage are pre-built. It just has to be adjusted in its lenght.

For the ARF version, the second M3 threaded piece must be glued into the carbon tube by thikened epoxy and the clevis mounted. Make two linkages, each approx. 935mm and 1000mm long.

The elevator linkage will be installed and adjusted also at 90° servo position and neutral pivot arm. This also results in the total length of the linkage.

Sand the rudder control horn well and glue into the rudder by using thickened epoxy resin.

Open the linkage outlet with a round file.
Then clip the linkage to the servo and rudder horn and adjust the linkage by the clevis to achieve a neutral rudder at 90° servo arm.

Connect the ESC to the motor and install it under the wooden tray in the front by velcro stripe. Check the running direction of the mo-tor already now and replace if necessary two of the three cables.

Make sure the cables are clean and can not drag on the motor.

The battery will be fixed by a velcro loop on the front battery tray. To avoid slipping the battery, a strip of Velcro should also be glued to the wooden board under the battery.

For later adjustment of the center of gravity, this can vary in its position. Only after the exact determination of the center of gravity you make a mark on the battery and the board.

The receiver has its place in the rear of the wooden tray and should be fixed by velcro.

Mount the propeller center section with propeller blades on the motor shaft. Pay attention to a firm but sensitive tightening of the nut. This is an aluminum thread!

Caution: Make sure that all rotating components are properly and firmly seated! Faulty installation can represent a safety risk and cause personal and property damage!

WINGS

Screw the rudder horns of the ailerons tightly into the threads provided. File a small recess so that the rudder can deflect downward.

The control horns of the flaps are glued under their cap with thickened epoxy. Ensure a correct angle of approx. 40° and that the rudder horn including clevis fits under the cap. The rudder horn must not stick out

Install the servos in the servo bay as shown. Use a wire to pull the servo cables through the openings provided. Then fabricate the aileron linkages from the M3 threaded parts and clevises. Hook the aileron linkages into the rudder and servo horns (outer servo). Again, make sure the rudder is neutral with the servo horn at a right angle and adjust this at the clevises if necessary. The linkage length is approx. 86mm.

The green 6-pin MPX connector system should be used as connection to the fuselage. The Scirocco is already provided with appropriate fits for our mounting frames

You can choose the pin assignment yourself, but pay attention to the polarity on the opposite side! Solder the cables to the pins and insulate them with heat shrink tubing.

Glue the connector to the mounting frame with super glue to form a unit and screw it into the recess.

Glue the torsion pins with epoxy. Check the precise fit of the two wing parts to each other beforehand. If necessary, slight corrections can be made at this stage.

The linkage of the flaps is realized by a crossover connection through the surface of the wing. Therefore the rod must initially be connected to the bottom side of the flap servo and routed through the upper side of the wing in order to be connected with the flap`s rudder horn. If the servo horn is positioned in a right-angle (neutral position), the deflection of the flap should read approximately 25mm downwards. To do this, manufacture a linkage approx. 82mm long.

Pay attention to a proper cable guide. Stash the excessive length of the leads away in the wing by surrounding with foam to avoid nasty noises.

Glue the servo and rod covers only after all electronic adjustments with UHU- Por. So the linkage can still be fine-tuned

A transparent strip of adhesive tape is sufficient to secure the surface connection.

Optional ARF: The plywood-reinforced root ribs make it possible to install a Multilock system and firmly glue the electrical wing connection. There are already small recesses in the mold where the wing can be easily separated with a wedge. If you don‘t want to look for the wing connectors every time you build the wing, you can also glue them firmly into the outer wing.

The elevator is connected to the fuselage by the carbon rod and the 2mm steel wire through the bore of the pivot arm.

To fix the elevator on the joiner rod we just recommend high friction.

This higher friction will be achieved by putting speed glue on the carbon tube.

The intensity of friction can be easily adjusted by applying or grin-ding the hardened glue.

Always pay attention to complete curing of the superglue before putting on the elevator

To prevent the pins from being lost so easily during transport, they can also be glued firmly into one tail unit half.

Insert both parts of the wing onto the wing connector and con-nect it together. Use M4 Allen socket screws to connect the wing with the fuselage.

Make sure that no wires are stuck between the fuselage and the wing. For securing the wing connection, a transparent strip of adhesive tape is sufficient.

Turn your transmitter and receiver on. Make sure that the correct model is adjusted on the memory of your transmitter. If possible, try to adjust all rods mechanically.

The next step is to check the running direction and travel ways of the servos. Therefore please note the grid below.

Mark the exact battery position in the fuselage with a felt-tip pen or tape.

The center of gravity is 94-100mm behind the leading edge. For beginner- compatible flight behavior, first set the center of gravity to 94mm. For faster all-rounder behavior, the center of gravity can slowly be moved further back.

Elevator angle of incidence is about 1-1.5°, depending on the adjusted CG. Simpler: with the fuselage level on the fuselage skid and tailplane, the elevator end rail should have 98mm height.

CONTROL THROWS

FLIGHT RECOMMENDATIONS

Now look for a day with suitable weather conditions for the first flight. With the mentioned settings you will be spared bad surprises. We recommend, at least on the first flight, to make the start with a starting helper. Enjoy your new model aircraft and „always happy landings!“.

SPARE PARTS

SCIROCCO XS: 2674 / 2675

SPARE PARTS

Spare part|   Item N.| Piece
Wing center section (without Electronics)| 267401| 1
Outer Wing Set (without Servos)| 267402| 1
Fuselage (w/o electronics)| 267403| 1
Tail plane| 267404| 1
Servo covers| 266807| 1
2-piece aluminum wing protection bag, also for tail plane| 78510074| 1
Aluminum fuselage protection bag| 78510075| 1

SCIROCCO XL: 2672 / 2673

 2-piece aluminum wing protection bag, also for tail plane  empennage horizontal| 78510076| 1
 Aluminums fuselage protection bag| 78510077| 1

SCIROCCO S: 2668 / 2669

SPARE PARTS

Spare part|   Item N.| Piece
Wing center section (without Electronics)| 266801| 1
Outer Wing Set (without Servos)| 266802| 1
Fuselage (w/o electronics)| 266803| 1
Tail plane| 266804| 1
servo covers| 266807| 1

SCIROCCO L: 2670 / 2671

SCIROCCO S/L/XL: 2668-2669 / 2670-2671

SPARE PARTS / PIÉCES DÉTACHÉES SCIROCCO S/L/XL: 2668-2669 / 2670-2671

Spare part|   Item N.| Piece
Canopy| 267005| 1
 Area connector| 267006| 1

SCIROCCO S/L/XL: 2668-2669 / 2670-2671

ACCESSORIES ELECTRO
SCIROCCO S/L/XL: 2668-2669 / 2670-2671

Accessories Electro| Item N.| Piece
RO-CONTROL 6-80 2-6S -80(100A) 5V/5A SWITCH BEC Regler / ESC| 8710| 1
Ro-Power ULTRA HP oder MAXAMP 4-5S 4000-5200mAh LiPo Akku / Battery| 7345/7370/7373/7348| 1
Robbe FS 335 BB MG HV Digital Servo| 9117| 2
Robbe FS 128 BB MG HV Digital Servo| 9114| 4
v BRUSHLESS Motor| 5802| 1
Protection Bag| 263306| 1
Folding Prop| 723475| 1
Alu Turbo Spinner| 263308| 1

DISTRIBUTOR

Telefon: +43(0)7582/81313-0
Mail: info@robbe.com
UID Nr.: ATU69266037
Copyright 2021
Service-Adresse
service@robbe.com +43(0)7582-81313-0
www.robbe.com

Austria
Phone: +43(0)7582/81313-0
Mail: info@robbe.com
UID No.: ATU69266037
„robbe Modellsport“ is a registered Trademark.
Errors, misprints and technical changes reserved.
Copyright 2021
Robbe Modellsport 2021
Copy and reprint only with our permission.
Service-Address
Contact your Dealer or:
Robbe Modellsport, Industriestraße 10,
4565 Inzersdorf im Kremstal
service@robbe.com, +43(0)7582-81313-0

Robbe Modellsport
Industriestraße 10
4565 Inzersdorf im Kremstal
Autriche
Téléphone: +43(0)7582/81313-0
Email: info@robbe.com
UID Nr.: ATU69266037
Copyright 2021
Robbe Modellsport 2021
Service
service@robbe.com, +43 7582-81313
www.robbe.com

References

• Robbe Modellsport - Offizielle Markenwebsite und Shop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>