Accell K078C-004B 1×4 HDMI Mini Splitter Owners Manual

Accell K078C-004B 1×4 HDMI Mini Splitter

READ ME FIRST – SETUP INSTRUCTIONS

Thank you for purchasing the Accell UltraAV HDMI Distribution Amplifier. This product is designed to provide exceptional performance and value. Please review the manual before operating and retain for future reference.

CAUTION

1. Ensure the unit has sufficient ventilation. Do not cover ventilation openings. Do not install in a confined space.
2. Do not operate near the source of heat. Do not stack on top, underneath, or between other heat-generating unit/s including other amplifiers.
3. Unplug the power adapter if not used for an extended period.
4. To prevent damage from power surges, the unit should be plugged into a surge protector or surge-protected power source.
5. Do not use near liquid or areas of heavy moisture.
6. Clean the unit with a clean and dry cloth only.
7. This unit cannot be serviced in the field. Contact Accell if service is required.
8. Do not open a case, risk of shock – shock hazard.
9. Do not modify the power cord or use the product if the power cord is damaged.

Introduction

The UltraAV HDMI Distribution Amplifier (Splitter) featuring HDBaseT Lite accepts a signal from a single HDMI-enabled audio/video source and splits the single input into 4 HDMI outputs. The audio/video signal is mirrored on up to 4 HDMI displays, monitors, projectors or TV’s.

• Over-Current and Over-Voltage Protection
  The circuit boards are equipped with both over-current and over-voltage protection and will automatically power down if encountered. The circuit boards will restore automatically once the excessive current or voltage has passed.

Package Contents

• HDMI Distribution Amplifier (Splitter)
• 1 Power Adapter (for Matrix)
• 4 HDBaseT Receivers
• 4 Power Adapters (for Receivers)
• Owners Manual
• 4-Pair IR-TX and IR-RX

1×4 HDMI Splitter with HDBaseT Lite Model: K078C-008B

Specifications

• Connect 1 HDMI Source to up to 4 HDMI Displays
• Supports HD resolutions up to 1080P and 3D
• HDMI 1.4a, HDCP 1.2 compliant
• Data transfer speed of 6.75Gbps (225MHz)
• Audio formats supported: DTS-HD 7.1, Dolby True-HD 7.1
• Deep color up to 36-bit
• Maximum HDMI input/output cable length: Up to 16ft./5m
• Maximum Cat5e/6 output cable length: Up to 230ft./70m
• Shelf or surface mountable
• 9V DC, UL Listed Power Supply for 1×4 Splitter Unit
• 5V DC, UL Listed Power Supplies for Receiver Units (4 Total)
• Input AC: 50Hz to 60Hz, 100-240V
• Splitter dimensions: 10.9”W x 1.1”H x 6.1”D (277W x 28H x 156D mm)
• Receiver dimensions: 4.4” W x .9” H x 3” D (112W x 23H x 76D mm)
• Operating temperature range: 5 to 131°F (-15 to 55°C)
• Operating humidity range: 5% to 90% RH (no condensation)

Setup

Note: All Cat5e/6 cables must be terminated to 568B standards.

• Unshielded (or properly terminated shielded cable), solid core Cat5e, Cat6, Cat6e, Cat7, or Cat7e cables can be used. A stranded core is not suggested as it can reduce signal transfer. Recommended to use a continuous length of cable terminated at the matrix and receiver ends.
  With the splitter power switch in the OFF position, connect the HDMI High- Speed cable from the HDMI Output of the audio/video source to the HDMI Input located on the rear of the splitter.

• Tips: Use the shortest length of HDMI cables possible at each point in the installation. Use only High Quality and High-Speed HDMI cables.

• Next, connect a Cat5e/6 cable to the HDBaseT Out 1 port on the rear of the splitter. Connect the other end of the Cat5e/6 cable to the HDBaseT IN port on the rear of the HDBaseT receiver positioned near the TV. Run a short, High-Speed HDMI cable from the HDMI Out port on the receiver to the HDMI In port on the TV. Plug a provided power adapter into an AC outlet and the other end into the HDBaseT receiver. Using the same steps, connect the remaining displays to the splitter.

• Important: The HDBaseT Receivers when operating are warm and do require space around the housing for air circulation and cooling. Do not enclose the HDBaseT receiver. If placed behind a component such as a TV, ensure that there is adequate space for air circulation and ambient cooling and that there is no heat being generated and transmitted to the receiver from the other device. Damage caused by improper placement and overheating of the splitter or the receiver is not covered by the product warranty.

LED Indicator Lights

On initial power on, all LED lights on the splitter should come on solid blue. If less than the maximum number of Displays are connected to the splitter (not all the outputs are used) there will be no corresponding HDMI OUT blue LED for the unused output. Blue lights will only appear for devices connected.

The HDBaseT Receiver has 4 LED indicators:

1. HDCP: A solid LED indicates that the HDCP handshake between the source and display has been authenticated.
2. Link: Indicates a connection between the Matrix and the Receiver.
3. Mode: A flashing LED indicates the correct operation of the system.
4. Power: A solid LED indicates power to the receiver.

Infrared Control (IR)

• The 1×4 Splitter featuring HDBaseT Lite includes 4 pairs of Infrared Extenders, 4 IR Transmitters (IR-TX), and 4 IR Receivers (IR-RX). The front panel of the splitter has 1 IR-TX port. The HDBaseT Receivers each have one IR-TX port and one IR-RX port. Using the included extenders, you can configure the IR to control the source devices when present at any of the displays.
• The port on the splitter labeled “IR” accepts an optional IR-TX, sending commands received from the IR-RX at the display end (HDBaseT receiver) to the IR “eye” on a source.
• Plug an IR-RX into the IR-RX Port of the HDBaseT receiver. Place the end of the IR-RX in an area that is in line of sight to the remote control.
• Plug an IR-TX into the IR port on the splitter. Position the end of the IR-TX in line of sight to the IR “eye” of the source device. The IR “eye” is normally a small circle on the face of the source device that receives the IR signal from its remote control.
• To control multiple source devices with one IR-TX, stack the sources together and position the IR-TX, which is plugged into the IR port on the splitter so that all the source devices can receive the IR signal (Blast) from the IR-TX.
• Note: A remote control is not included. A remote control programmed to control the source device/s is required for IR operation.

1. Ultra-IR Receiver (5 ft.)
   • Dual Frequency: 38KHZ-60KHZ
   • PN: B164B-002B
2. Ultra-IR Transmitter (5 ft.)
   • Dual Frequency: 38KHZ-60KHZ
   • PN: B164B-003B
3. Ultra-IR Receiver and Transmitter Pin Assignment

Troubleshooting

• One of the displays does not show a picture or output audio.
  Check the display’s input setting to ensure it is set to receive a signal from the connected HDMI port.

• One or more of the connected displays will not display a picture while one or more of the displays do display a picture:
  Press the RESET button on the front of the splitter to reset it. Alternatively turn off the power to the splitter, source, and displays. Wait 60 seconds. Turn the source on and the displays on. Turn the splitter on. A2. The HDMI cables on the non-functional display/s cannot support their long length. Use only high-quality High-Speed HDMI cables. Keep the cable length as short as possible. Test by locating the non-working display close to the splitter. Use a short HDMI cable to connect the switch to the TV. A working TV using a short HDMI cable indicates an issue with the HDMI cable.

• The splitter is not down-sampling the video and some of the TVs are not displaying a picture.

  • Go into the TV setup and configure the resolution to match all the connected TVs. The TVs should share the same resolution.
  • In the source devices menu options set the source device to output a resolution that matches all the connected displays.

• My TV’s resolution is not optimized.
  The splitter will query the displays and provide the highest common video resolution amongst them. Example: Using a 1080p source, if 3 of the displays support a maximum resolution of 1080p and 1 display supports a maximum resolution of 720p, all 4 displays will operate at a resolution of 720p. If the 720p TV in the example is then turned off, the other 3 displays can then operate in 1080p resolution. Press the RESET button on the front panel of the splitter to refresh the configuration. The three 1080p TVs will refresh (flicker) then each will display a 1080p resolution picture.

• My TV’s resolution is not optimized.
  The splitter will query the displays and provide the highest common video resolution amongst them. Example: Using a 1080p source, if 3 of the displays support a maximum resolution of 1080p and 1 display supports a maximum resolution of 720p, all 4 displays will operate at a resolution of 720p. If the 720p TV in the example is then turned off, the other 3 displays can then operate in 1080p resolution. Press the RESET button on the front panel of the splitter to refresh the configuration. The three 1080p TVs will refresh (flicker) then each will display a 1080p resolution picture.

• Get the message “This protocol is not supported” or another error message.

  • See answer A1 above and repeat the steps outlined.
    ASSISTANCE: Questions regarding this product or its product warranty, please check out our Web site at: www.accellcables.com. Customer service can be reached by email at support@accellcables.com or by phone at 510-438-9288, toll-free 877-353-0772 (M-F 9 am-5 pm PST).

1-YEAR MANUFACTURERS WARRANTY

The Accell UltraAV Splitter is warranted for one year from the date of purchase to be free of defects in material and workmanship. In the event of such defects, the Accell product will be repaired without charge or replaced with a new one at our option, if delivered to Accell Corporation prepaid, together with a copy of the sales receipt indicating the proof of purchase date and place of purchase. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use the product in accordance with the instructions. ACCELL CORPORATION SHALL NOT BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, INTERRUPTED OPERATION OR COMMERCIAL LOSS, OR ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. YOU AGREE THAT ACCELL’S MAXIMUM LIABILITY ARISING FROM ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE OF SUCH PRODUCT. SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN DAMAGES, SO THE ABOVE MAY NOT APPLY TO YOU TO THE EXTENT SUCH JURISDICTION’S LAW IS APPLICABLE TO THIS AGREEMENT. This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

LIMITATION OF LIABILITY

• IN NO EVENT SHALL ACCELL CORPORATION, ITS SUBSIDIARIES OR AFFILIATES, OR THEIR RESPECTIVE PARTNERS, OFFICERS, DIRECTORS, EMPLOYEES, SHAREHOLDERS, REPRESENTATIVES OR AGENTS (COLLECTIVELY, “ACCELL”) BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR INDIRECT DAMAGES (INCLUDING BUT NOT LIMITED
• TO, LOSS OF DATA, USE, OR PROFITS), HOWEVER, CAUSED, WHETHER FOR BREACH OF CONTRACT, NEGLIGENCE, OR OTHERWISE, AND WHETHER OR NOT ACCELL HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. YOU AGREE THAT ACCELL’S MAXIMUM LIABILITY ARISING FROM ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE OF SUCH PRODUCT. SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN DAMAGES, SO THE ABOVE MAY NOT APPLY TO YOU TO THE EXTENT SUCH JURISDICTION’S LAW IS APPLICABLE TO THIS AGREEMENT.

WARRANTY RETURNS PROCEDURE

Contact Customer Support to obtain a Return Authorization (RMA) number. RMA numbers are valid for 30 days from the date of issuance. We are unable to accept returns without an RMA number. Returns without an RMA number clearly printed on the outside of the package will be refused and returned unopened. All returns must be shipped prepaid at the expense of the shipper.

Accell assumes no responsibility for any inaccuracies and liability for direct, indirect, special, incidental, or consequential damages as a result. Due to ongoing improvements, Accell reserves the right to make changes to hardware, packaging, and any accompanying documentation without prior written notice.

©2013 Accell Corporation, All Rights Reserved. Accell and UltraAV are registered trademarks of Accell Corporation.

FREQUENTLY ASKED QUESTIONS

What is the Accell K078C-004B HDMI Mini Splitter?

The Accell K078C-004B is a device that allows you to split a single HDMI input signal into four separate HDMI output signals.

What is the purpose of using an HDMI splitter like the Accell K078C-004B?

The HDMI splitter is used to distribute a single video and audio source to multiple displays or devices simultaneously, such as TVs, monitors, projectors, etc.

How many HDMI inputs does the Accell K078C-004B have?

The Accell K078C-004B has one HDMI input.

How many HDMI outputs does the Accell K078C-004B have?

It has four HDMI outputs.

What is the maximum supported resolution of the Accell K078C-004B?

The Accell K078C-004B typically supports resolutions up to 4K Ultra HD (3840 x 2160) at 60Hz.

Does the Accell K078C-004B support audio pass-through as well?

Yes, it usually supports audio pass-through along with video.

Is the Accell K078C-004B compatible with HDCP (High-bandwidth Digital Content Protection)?

Yes, it is usually compatible with HDCP, allowing you to play protected content.

Can I use the Accell K078C-004B for gaming consoles?

Yes, you can use it to connect gaming consoles to multiple displays simultaneously.

How do I set up the Accell K078C-004B?

Connect your HDMI source to the input port and connect up to four HDMI displays to the output ports using HDMI cables.

Does the Accell K078C-004B require external power?

Yes, it often requires external power, which is usually provided through an included power adapter.

Can I use different HDMI cable lengths for the outputs?

Yes, you can use different cable lengths for the outputs, but keep in mind that longer cables might affect signal quality.

Is the Accell K078C-004B a powered or passive splitter?

The Accell K078C-004B is a powered splitter, meaning it requires an external power source to function.

Can I daisy-chain multiple Accell K078C-004B units together?

It's generally not recommended to daisy-chain HDMI splitters, as it can lead to signal degradation.

What's the typical range for the remote control of the Accell K078C-004B?

The range of the remote control can vary, but it's usually within a reasonable distance, around 5 to 10 meters.

Can I use the Accell K078C-004B to extend my desktop across multiple displays?

No, the Accell K078C-004B is a splitter, not an extender. It duplicates the same signal to multiple displays.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>