OSD BLACK T63LCR 6.5 Inch In Wall Center Speaker Installation Guide
- June 12, 2024
- OSD BLACK
Table of Contents
OSD BLACK T63LCR 6.5 Inch In Wall Center Speaker
Product Information:
- Product: T63LCR In-Wall LCR Speaker
- Woofer: Dual 6.5 Carbon Fiber Cone
- Tweeter: 1 Aluminum Dome
- Power Handling: 200W
- Sensitivity: 87dB 1w/1m
- Frequency Response: 45Hz – 22kHz
- Impedance: 8 ohms
- Dimensions: (LxW) 15.9 x 8.9 inches
- Cut Out: 14.3 x 7.4 inches
- Mounting Depth: 3.3 inches
Product Usage Instructions
- Preparation:
- Gather the following tools for installation: Pencil, Drill, Tape Measure, Wire Cutter, Safety Eye Wear, Phillips Screwdriver, Gloves, Utility Knife, and Sandpaper.
- Refer to the Speaker Wire Guide for choosing the appropriate wire gauge based on the distance.
- Consider the best place to install the speakers and ensure they are separated 6 – 10 feet apart.
- Placement:
- Depending on speaker type and application, carefully plan the placement of the speakers.
- Installation may require cutting a hole in your wall or ceiling.
- Refer to Diagram 1 for typical speaker placement in a 5.1 or 7.1 speaker system.
- Installation:
- Refer to Diagram 2 for the cut-out process.
- Tighten the mounting brackets by turning the screws on the front of the speaker baffle clockwise to securely hold the speaker in place.
- Ensure the speaker is fully tightened to the locked position.
- Connection:
- Before connecting the speakers to the amplifier or receiver, ensure the power is off.
- Locate the connection terminals on the back of your receiver or amplifier.
- Connect the audio out from the back of your receiver or amplifier to the speakers following Diagram 4.
- Note that not all Amplifier/Receivers can safely play more than one pair of speakers at once. Refer to your owner’s manual for impedance and wattage compatibility.
- Adjustment:
- To pivot the tweeter, press on it as indicated in Diagram 6.
WARRANTY: This product is covered by a warranty provided by Optimal Speaker Design. For more information, visit osdaudio.com.
Preparation
Tools For Installation
- Pencil
- Drill
- Tape Measure
- Wire Cutter
- Phillips Screwdriver
- Utility Knife
- Safety Eye Wear
- Gloves
- Sandpaper
Speaker Wire Guide
- 18AWG minimum – for distances up to …………………. 10 ft
- 16AWG – from …………………………………..…… 10 to 50 ft
- 14AWG – from ……………………………………… 50 to 100 ft
Considerations
- Where is the best place to install the speakers?
- Where do the speakers sound the best?
- Separate the speakers 6 – 10 feet apart.
Placement
There are many options for proper speaker placement depending upon speaker
type and application. It’s important to carefully plan the placement of your
speakers, as installation requires that you cut a hole in your wall or
ceiling.
(See Diagram 1.) Typical speaker placement for a 5.1 and 7.1 speaker system.
Installation
Cut Out
NOTE: This is the most important part of the entire installation. If you are
not certain whether any obstructions exist behind the desired mounting area,
you should start by cutting a small hole in the center of your penciled
mounting hole with a drywall saw.
Using the Cut Out dimensions measure and trace a template on the wall in the
desired location. Cut along the traced line using a drywall saw or rotary
drill. Use a piece of sandpaper to sand down the cut out edge for a smoother
contour. (See Diagram 2.)
Mounting
Tighten the mounting brackets by simply turning the screws on the front of the speaker baffle slowly clockwise. The quick-turn mounting system and frame will “sandwich” or clamp around the dry-wall to hold the speaker securely in place once fully tightened to the locked position. (See Diagram 3.)
Connection
When connecting any speakers to the amplifier or receiver, always make sure
the power is off. Locate the connection terminals
on the back of your receiver or amplifier. Always make sure to connect audio
out from the back of your receiver or amplifier to the speakers. (See Diagram
4.)
NOTE: Not all Amplifier/Receivers can safely play more than one pair of
speakers at once. Please refer to your owner’s manual for impedance and
wattage compatibility.
Adjustment
On select models a front mounted 3 position ±3dB treble & or bass contour
switch can be used to tailor high frequencies according to speaker placement
or the listeners preference.
(See Diagram 5.)
Pivoting Tweeter
Your Black series speaker comes from the factory with the tweeter centered in
the neutral position. This will provide the smoothest response. However,
select models come with a pivoting tweeter so you can focus the sound directly
towards the listening area if needed. In order to do this, carefully press on
the edge of the tweeter baffle in the direction you wish to focus the sound.
(See Diagram 6.)
CAUTION: When adjusting the pivoting tweeter be sure not to touch the dome as
you may cause damage to the speaker.
Specifications
T63LCR
In-Wall LCR Speaker
- Woofer: Dual 6.5” Carbon Fiber Cone
- Tweeter: 1” Aluminum Dome
- Power Handling: 200W
- Sensitivity: 87dB 1w/1m
- Freq Response: 45Hz – 22kHz
- Impedance: 8 ohms
- Dimension: (LxW) 15.9” x 8.9”
- Cut Out: 14.3” x 7.4”
- Mounting Depth: 3.3”
WARRANTY
-
All Optimal Speaker Design speaker products have Limited Lifetime Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period Optimal Speaker Design will replace any defective part and correct any defect in workmanship without charge for either parts or labor Optimal Speaker Design may replace returned speakers with a product of equal value and performance. In such cases, some modification to the mounting may be necessary and are not Optimal Speaker Designs responsibility.
-
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by Optimal Speaker Design. The unit must be returned to Optimal Speaker Design at the owner’s expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damaged resulting from abuse or from servicing performed by an agency or person not specifically authorized in writing by Optimal Speaker Design
Optimal Speaker Design sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any Optimal Speaker Design product purchased from an unauthorized dealer or other source, including retailers, mail over dealers and on-line sellers will not be honored or serviced under existing Optimal Speaker Design warranty policy. Any sale of product by an unauthorized source or other manner not authorized by Optimal Speaker Design shall void the warranty on the applicable product. -
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at RMA@audiogeargroup.com for a Returned Merchandise Authorization (RMA) number# then the unit must be shipped to Optimal Speaker Design at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
-
This Warranty Does Not Cover: Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any products that have been altered or modified • Any product whose identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal wear and maintenance.
Optimal Speaker Design | Brea, CA | osdaudio.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>