EIZO DuraVision FDX1501-A Color LCD Monitor User Guide

Dura Vision FDX1501-A
Color LCD Monitor
Dura Vision FDX1501T-A
Touch Panel Color LCD Monitor

Dura Vision FDX1501-A Color LCD Monitor

Setup Manual Important:
Please read this Setup Manual and the User’s Manual stored (on the CDROM) carefully to familiarize yourself with safe and effective usage. Please retain this manual for future reference.
Compatible Resolutions
The monitor supports the following resolutions.

*1 Recommended resolution.

SAFETY SYMBOLS

This manual and this product use the safety symbols below. They denote critical information. Please read them carefully.

WARNING| Failure to abide by the information in a WARNING may result in serious injury and can be life threatening.
---|---
CAUTION| Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage.
| Indicates a warning or caution. For example, indicates an “electrical shock” hazard.
---|---
| Indicates a prohibited action. For example, means “Do not disassemble”.
| Indicates a mandatory action. For example, means “Ground the unit”.

About Setup Manual and User’s Manual

Setup Manual (this manual)| Describes basic information ranging from connection of the monitor to a PC to using the monitor.
---|---
| User’s Manual of this monitor 1| Describes the application information of the monitor such as screen adjustments, settings, and specifications.
User’s Manual of Touch Panel Driver 1| Describes the installation and use of the touch panel driver.

*1 PDF file on the CD-ROM (Installation of Adobe Reader is required.)
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are subject to change without notice.

PRECAUTIONS

IMPORTANT

• This product is intended to be used with an industrial device designed to build industrial systems.
  – Transportation systems (Ship, aircraft, train, automobile, etc.)
  – Safety devices (Disaster prevention system, security control system, etc.)
  – Equipment with direct effect on human life (Life support systems, Medical equipment or devices used in the operating room, etc.)
  – Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
  – Main line devices (Operation control for transportation, control systems specific to aircrafts, etc.)

• To ensure personal safety and proper maintenance, please read this section.

WARNING
This product is intended to be housed in an enclosure. Do not use the bare monitor separately.
Attempting to use a malfunctioning unit may result in electric shock, or equipment damage.
If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your local EIZO representative for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in ferrielectric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/ spills into the cabinet, unplug the unit immediately. Have the unit checked by a qualified service engineer before using it again.
Use the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.

• Do not place outdoors.
• Do not place in a transportation system (ship, aircraft, train, automobile, etc.) where it may be affected by strong vibration or shock.
• Do not place in a dusty or humid environment.
• Do not place in a location where water is splashed on the screen (bathroom, kitchen, etc.).
• Do not place in a location where the steam comes directly on the screen.
• Do not place near heat generating devices or a humidifier
• Do not place in a location where the product is subject to direct sunlight.
• Do not place in an inflammable gas environment.
• Do not place in environments with corrosive gases (such as sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, and ozone)
• Do not place in environments with dust, components that accelerate corrosion in the atmosphere (such as sodium chloride and sulfur), conductive metals, and so on

Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal that may leak from the panel is poisonous if it enters the eyes or mouth. If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor.
WARNING
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the cord attached is dangerous. It may result in injury.
Do not install the unit in a closed space.
If the inerior becomes hot, it may result in fire, electric shock or damage.
Do not use the power jack and DC power terminal block at the same time.
This may result in fire, electric shock, or damage to the power supply system.
Periodically check the tightening of screws.
If screws are loose, the monitor may detach and cause injury or equipment damage.

Notice for this monitor

This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:

• Signal cables specified by us

Only use optional products manufactured or specified by us with this product.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to “Cleaning” (page 5)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact your local EIZO representative.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the monitor.
When mounting the monitor in an enclosure, always ground the monitor to avoid the effects of static electricity on the monitor internals and LCD panel.
(Cautions for the Use of the Touch Panel)

• During touch operation

Be careful of the following points. Otherwise, damage may occur to the monitor.

• Do not strongly press, scratch, or poke the panel.
• Do not touch the panel with hard objects such as ballpoint pens or metals.

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
• Do not allow liquid to enter the clearance between the panel and the panel frame.

Note

• The optional Screen Cleaner is recommended for cleaning the panel surface.

If necessary, the stains on the panel surface can be removed by moistening part of a soft cloth with water.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

Package Contents

Check that all the following items are included in the packaging box. If any items are missing or damaged, contact your local EIZO representative.
Note

• Please keep the packaging box and materials for future movement or transport of the monitor.

• Monitor

• Analog signal cable : MD-C87

• USB cable: MD-C93 (for FDX1501T-A only)

• EIZO LCD Utility Disk (CD-ROM)

• Setup Manual (this manual)

• VESA mounting screws M4 × 10: 4 pcs.

• Screws for fixing the clamper M4 × 10 : 2 pcs.
  (Prepare a screwdriver.)

• Metal panel fittings: 8 pcs. (Panel mount type only)
  (Prepare a screwdriver.)

Attention

• This product does not include a power cord. Please provide separately a power cord which meets the usage requirements. For more information, please contact your local EIZO representative.

Controls and Functions

Example : FDX1501T-A (Chassis mount type)

screen, and saves

adjusted values.

4. ▼▲   button| •   Provides the menu selection as well as the adjustment and setting of a function.
•   Displays the Brightness menu.
5. button| Turns the power on or off.
6. Power indicator| Indicates the monitor’s operation status.
Blue : Operating    Orange : Power saving mode    OFF: Power off
7. Power connector| Left : DC power terminal block / Right : Power jack (DC-IN)
8. Input signal connector| Left : DVI-D connector / Right : D-Sub mini 15-pin connector
9. USB upstream port (for FDX1501T-A only) 2| Connects a PC and monitor via a USB cable when this product is used as a touch panel monitor.
10. RS-232C port (for FDX1501T-A only) 2| Connects a PC and monitor via a RS-232C cable when this product is used as a touch panel monitor.
11. Button extension connector| This is an extension connector for using the external control buttons.
12. Screw holes for securing the clamper (2)| Attach the clamper to prevent the cable from falling off. Fit the cable in the clamper and fit it with the set screw (M4 × 10), as shown in the diagram above.

1 For instructions for use, refer to the User’s Manual on the CD-ROM.
2 These ports cannot be used at the same time. When cables are connected to both ports, the USB port is prioritized.

Assembly

Attention

• Before mounting the monitor into the enclosure, please perform all settings and adjustments of the monitor, and installation of the touch panel driver.
• When attaching an arm or stand, the installable orientations and movement range (tilt angle) are as follows:

Chassis mount type

Exterior view
FDX1501T-A

*1 DC power terminal block

Connector Pin Assignment

Power sequencing

**2 Button extension connector: S3B-PH-SM4-TB(LF)(SN) (JST) Connector Pin Assignment

How to assemble

1. Fasten the screws through the enclosure mounting holes of the monitor (2 each on the left and right sides) into the enclosure.

Attention

•  Please prepare screws that have a diameter of 3 mm and are suitable for use with the enclosure. (Screws are not included with the monitor.)

Panel mount type

Exterior view
FDX1501-A

FDX1501T-A

*1 DC power terminal block

Connector Pin Assignment

Power sequencing

*2 Button extension connector: S3B-PH-SM4-TB(LF)(SN) (JST)
Connector Pin Assignment

How to assemble
Attention

• Since the panel mounted on the monitor is tightened with a metal panel fitting screw, please make the selection considering the following points.
  – Flat
  – A thickness of 5 mm
  – A structure having the strength to support fixing with the screw.

1.  Insert the monitor into the mount opening of the panel from the front.
   The dimensions of a fitting opening are the “Panel opening dimensions” shown in the exterior view.

2. Fit the included metal panel fittings onto the monitor (8 locations).

3. Tighten the screws of the metal panel fittings with a prescribed torque of 0.6-0.7 N·m.

Connecting Cables

Attention

• Check that the monitor and the PC are powered off.
• When replacing the current monitor with this monitor, be sure to change the PC settings for resolution and vertical scan frequency to those that are available for this monitor. Refer to the compatible resolution table before connecting the PC.

1. Connect the signal cables to the input signal connectors and PC.
   Check the shape of the connectors, and connect the cables.
   After connecting the signal cable, tighten the screws of the connectors to secure the coupling.

2. Connect the monitor to a power supply.
   There are two options for connecting the monitor to a power supply. Make the connection according to the installation environment and conditions of use.
   • Using the DC power terminal block
   • Using the DC power jack (DC-IN)

Displaying the Screen

1. Press to turn on the monitor.
   The monitor’s power indicator lights up blue.

2. Turn on the PC.
   The screen image appears.
   If an image does not appear, refer to “No picture” (page 15) for additional advice.
   If using the FDX1501T-A proceed with installation and calibration of the touch panel driver.

Attention

• Turn off the monitor and PC after using them.
• For the maximum power saving, it is recommended that the Power button be turned off. Turning off the main power switch or unplugging the power plug completely shuts off power supply to the monitor.

Installing the Touch Panel Driver (FDX1501T-A)

Attention

• The user account to be used for installing the touch panel driver must have the “Administrators” privilege.
• When reinstalling the touch panel driver to update the driver, etc., restart the PC after uninstalling the driver and then install it.

1. Uninstall the other touch panel driver, if it is installed.
2. Install the touch panel driver according to the instructions included in the CDROM. For how to install the touch panel driver, see the Touch Panel Driver User’s Manual (on the CD-ROM).
3. Use the USB cable or RS-232C cable to connect the monitor and the PC.
4. Restart the PC.

Attention

• When using the RS-232C cable with Windows 7 / Windows Vista / Windows XP, set up the device using the following procedure after the restart. For details, refer to the Touch Panel Driver User’s Manual (on the CD-ROM).
  1. Click “Start” – “All Program” – “DMC” – “DMC Touch Panel Configuration” to display “Properties” window.
  2. Click “Add a serial device”, and register a new serial device.
  3. Click “Device”, and specify the COM port number used for the “COM port”.
  4. Click “Apply”.
  5. Click “Close”.

Calibrating the Monitor (FDX1501T-A)

Calibrate the monitor according to the Touch Panel Driver User’s Manual (on the CD-ROM).
Note

• If its installation location has changed, please perform calibration.

Troubleshooting

• No picture
  If a problem still remains after applying the suggested remedies, contact your local EIZO representative.

1. No picture
•   Power indicator does not light.
•   Power indicator is lighting blue.
•   Power indicator is lighting orange.| •   Check whether the power cord is connected properly.
•   Press .
•   Increase “Brightness” and/or “Gain” in the Setting menu.
•   Switch the input signal with .
•   Move the mouse or press any key on the keyboard.
•   Check whether the PC is turned on.
•   Depending on the PC and graphics board, the input signal is not detected and the monitor does not recover from the power saving mode. If the screen is not displayed even after moving the mouse or pressing any key on the keyboard, turn the monitor off and on using its power button. When the screen is displayed, execute the following procedure. The problem may be improved.
1. Press  to turn off the monitor.
2. Hold down  while pressing  to turn on the monitor. “x” is displayed on the menu title of “Information” of the Setting menu.
3. Reboot the PC.
To return to the previous setting, perform steps 1 to 3 again.
2. The message below appears.
•   The message shows that the input signal is out of the specified frequency range. Example:| This message appears when the signal is not input correctly even when the monitor functions properly.
•   Check whether the PC is configured to meet the resolution and vertical scan frequency requirements of the monitor (see “Compatible Resolutions”).
•   Reboot the PC.
•   Select an appropriate setting using the graphics board’s utility. Refer to the User’s Manual of the graphics board for details.

Specifications

Microsoft Windows 10 (32 bit / 64 bit)
Microsoft Windows 8.1 (32 bit / 64 bit)
Microsoft Windows 7 Service Pack 1 (32 bit / 64 bit) Microsoft Windows Vista Service Pack 2 (32 bit) Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Video Signals| Input Terminals| DVI-D connector × 1, D-Sub mini 15-pin × 1
Digital Scanning Frequency (H / V)| 31 kHz – 49 kHz / 59 Hz – 61 Hz (720 × 400 : 69 Hz – 71 Hz)
Analog scan frequency Frequency (H / V)| 24 kHz – 61 kHz / 55 Hz – 76 Hz
Dot Clock| Digital :
Analog :| 65 MHz
80 MHz
Synchronous signal| Separate, TTL, positive / negative
Communication (FDX1501T-A)| Input Terminals| RS-232C :| D-Sub 9-pin (male)
USB (FDX1501T-A)| Port| Upstream port × 1
Standard| USB Specification Rev.2.0
Power| Input| DC 12 V ± 10%, 1.0 A
Maximum Power Consumption| 12.0 W or less
Power Save Mode| 1.0 W or less
Standby Mode| 0.5 W or less (USB device is connected)
Physical Specifications| Dimensions (Width) × (Height) × (Depth)| Chassis mount type| 383 mm × 331 mm × 62 mm
Panel mount type| 357.4 mm × 273.5 mm × 61 mm
Net Weight| Chassis mount type| FDX1501-A :
FDX1501T-A :| Approx. 2.5 kg
Approx. 3.3 kg
Panel mount type| FDX1501-A :| Approx. 3.6 kg
FDX1501T-A :| Approx. 3.7 kg
Operating Environmental Requirements| Temperature| 0˚C to 50˚C (32˚F to 122˚F)
Humidity| 20% to 90% R.H. (no condensation)
Air pressure| 540 hPa to 1060 hPa
Transportation / Storage Environmental Requirements| Temperature| -20˚C to 60˚C (-4˚F to 140˚F)
Humidity| 10% to 90% R.H. (no condensation)
Air pressure| 200 hPa to 1060 hPa

Main default settings

153 Shimokashiwano, Hausman, Ishikawa 924-8566 Japan
www.eizoglobal.com
www.eizo.co.jp
Copyright © 2015 – 2022 EIZO Corporation. All rights reserved.
00N0L908E1
SUM-FDX1501ACP-AL
5th Edition – June, 2022 Printed in Japan.

References

• ユーザー登録 | EIZO株式会社
• EIZO株式会社
• EIZO GLOBAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>