infobit iSwitch 104H150 18Gbps HDMI 1×4 HDBaseT Splitter User Manual
- June 12, 2024
- infobit
Table of Contents
- infobit iSwitch 104H150 18Gbps HDMI 1×4 HDBaseT Splitter
- Product Information
- Product Usage Instructions
- Introduction
- Features
- Package Contents
- Specifications
- Operation Controls and Functions
- EDID Mode
- ASCII Commands
- Application Example
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
infobit iSwitch 104H150 18Gbps HDMI 1×4 HDBaseT Splitter
Product Information
- Product Name: iSwitch 104H150
- Version: 1.0
- Manufacturer: www.infobitav.com
Description: This product is an 18Gbps HDMI 1×4 HDBaseT Splitter that can distribute 1 source signal to any 4 display devices. It supports HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliance, and has a video bandwidth of 18Gbps. The product supports video resolutions up to 4K2K@60Hz, HDR, HDR10+, HLG, Dolby vision, and up to 7.1CH HD audio pass-through. It can extend the signal transmission distance up to 120 meters at the resolution of 4K2K@60Hz, and 150 meters at 1080P@60Hz via a single CAT6/6a/7 cable. The product also features advanced EDID management, support for one-way POC function, and a compact design for easy installation.
Product Usage Instructions
- Connect the HDMI source device to the “IN” port of the transmitter using an HDMI cable.
- If you want to connect another display device directly to the transmitter, connect it to the “LOOP OUT” port using an HDMI cable.
- Connect the HDBaseT receivers to the “OUT(1~4)” ports of the transmitter using CAT6/6a/7 cables.
- If you want to control the transmitter or receiver using an IR or RS-232 device, connect them to the “IR” or “RS-232” ports respectively.
- If you want to extract audio from the HDMI source, connect the audio output device to the “AUDIO OUT” port.
- Connect the power supply to the transmitter using the provided DC 24V power adapter.
- Make sure all connections are secure and properly connected.
- Power on the transmitter using the “ON/OFF” switch.
- The “POWER LED” will turn red to indicate that the device is powered on.
- The “IN LED” will turn green if the HDMI IN port is connected to an active source device.
- The “LOOP LED” will turn green if the HDMI LOOP OUT port is connected to an active display device.
- The corresponding “OUT(1~4) LED” will turn green if the HDBaseT OUTPUT port is connected to a receiver.
Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully
before connecting, operating or adjusting this product. Please keep this
manual for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the
life of your equipment.
Introduction
This 18Gbps HDMI 1×4 HDBaseT Splitter can distribute 1 source signal to any 4 display devices. The HDMI signal transmission distance can be extended up to 120 meters at the resolution of 4K2K@60Hz, 150 meters at 1080P@60Hz via a single CAT6/6a/7 cable. The product supports up to 7.1CH HD audio pass- through. Audio extract function and advanced EDID management are supported.
Features
- HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
- Support 18Gbps video bandwidth
- Support video resolution up to 4K2K@60Hz 4:4:4
- Support HDR, HDR10+, HLG and Dolby vision
- Support up to 7.1CH HD audio pass-through
- Support digital and analog audio de-embedded output
- Extend the signal transmission distance up to 120 meters at the resolution of 4K2K@60Hz, 150 meters at 1080P@60Hz via a single CAT6/6a/7 cable
- Support 1 HDMI input, 1 HDMI loop output and 4 HDBaseT outputs.
- IR, RS-232 routed to HDBaseT output
- Advanced EDID management
- Support one-way POC function (only from transmitter to receiver)
- Compact design for easy and flexible installation
Package Contents
- 1 × 18Gbps HDMI 1×4 HDBaseT Splitter
- 4 × HDBaseT Receiver
- 5 × IR Blaster Cable (1.5 meters)
- 5 × 20K~60KHz IR Receiver Cable (1.5 meters)
- 5 × 3-pin Phoenix Connector
- 1 × 5-pin Phoenix Connector
- 10 × Mounting Ear
- 1 × 24V/2.7A DC Locking Power Adapter
- 1 × User Manual
Specifications
Technical|
---|---
HDMI Compliance| HDMI 2.0b|
HDCP Compliance| HDCP 2.2/1.x|
Video Bandwidth| 594MHz/18Gbps|
Video Resolution| Up to 4k2k@60Hz 4:4:4|
Color Depth| 8-bit,10-bit,12-bit(1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4)
8-bit,10-bit,12-bit(4K2K@60Hz YCbCr 4:2:2/4:2:0)|
Color Space| RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 / 4:2:0|
HDR| Support HDR, HDR10+, HLG, Dolby vision|
HDMI Audio Formats| LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD,
Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X|
Coaxial Audio Formats| PCM2.0, Dolby Digital / Plus, DTS 2.0/5.1|
Analog Audio Formats| PCM 2.0CH|
ESD Protection| Human body model—±8kV (Air-gap discharge) & ±4kV (Contact
discharge)|
Connection|
Input| 1×HDMI Type A (19-pin female)|
Output| 1×HDMI Type A (19-pin female） 4x HDBaseT OUT [RJ45] 1x Coaxial Audio
OUT [RCA] 1x L/R Audio OUT [5-pin phoenix connector]|
Control| 1×RS-232 (3-pin phoenix connector） 1x EDID DIP switch [5-pin] 1x IR
IN [3.5mm Stereo Mini-jack] 1x IR OUT [3.5mm Stereo Mini-jack]|
Mechanical
Housing| Metal Enclosure
Silkscreen Color| Black
Dimensions| Transmitter: 220mm (W) × 130mm (D) × 40mm (H) Receiver: 140mm (W)
× 65mm (D) × 18mm (H)
Weight| Transmitter: 853g Receiver: 246g
Power Supply| Input: AC100 – 240V 50/60Hz, Output: DC 24V/2.7A
(US/EU standards, CE/FCC/UL certified)
Power Consumption| 35W
Operation Temperature| 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature| -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity| 20~90% RH (non-condensing)
Operation Controls and Functions
Transmitter
| No. | Name | Function Description |
|---|---|---|
| 1 | POWER LED | When the device is powered on, the red power LED will be on. |
| 2 | IN LED | When the HDMI IN port connects an active source device, the green |
LED will be on.
3| LOOP LED| When the HDMI LOOP OUT port connects an active display device,
the green LED will be on.
4| OUT(1~4) LED| When the HDBT OUTPUT port connects an HDBaseT Receiver, the
corresponding green OUT LED will be on.
Rear Panel
| No. | Name | Function Description |
|---|---|---|
| 1 | RS-232 | Connect to a PC or control system via a 3-pin phoenix connector |
cable for three functions:
1, Firmware update;
2, Control the Splitter via RS-232 commands;
3, RS-232 signal pass-through (from transmitter to receiver or from receiver
to transmitter).
2| IR IN| Connect to IR receiver cable, the IR receive signal will emit to “IR
OUT” port of the HDBaseT Receiver.
3| IR OUT| Connect to IR blaster cable, the IR emit signal is from “IR IN”
port of the HDBaseT Receiver.
4| AUDIO OUT (COAX, L/R)| Coaxial/balanced audio output port, connect to
amplifer or speaker.
5| POWER switch| Press this switch to power on/off the device.
6| EDID DIP switch| Used to set EDID mode. Please refer to Section “6. EDID
Mode” for details.
7
| HDMI port| IN: HDMI input port, connect to HDMI source device such as DVD or
set-top box with an HDMI cable.
LOOP OUT: HDMI loop output port, connect to the HDMI display device such as TV
or Monitor with an HDMI cable.
8| HDBT OUTPUT port (1~4)| Connect to the HDBT IN port of the HDBaseT receiver
with a CAT cable.
9
| Link Signal Indicator lamp (Green)|
- Illuminate: Transmitter and receiver are connected.
- Dark: Transmitter and receiver are not connected.
10
| Data Signal Indicator lamp (Orange)|
- Illuminate: There is signal transmission between the transmitter and the receiver.
- Dark: No signal transmission.
11
|
DC 24V
| Plug the DC 24V power supply into the unit and connect the adaptor to an AC outlet. (Note: The transmitter can power the receiver via a CAT cable.)
HDBaseT Receiver
| No. | Name | Function Description |
|---|---|---|
| 1 | Power Indicator | When the receiver is powered on, the power indicator will |
be on.
2| SERVICE port| Used for firmware update.
3| DC 24V| Plug DC 24V/1A power supply into the unit and connect the adapter
to an AC outlet.( Note: The HDBase receiver also can be powered by the
transmitter via a CAT cable.)
4| HDBT IN| Connect to the HDBT OUTPUT port on the transmitter with a CAT
cable.
5| HDMI OUT| HDMI output port, connect to HDMI display device such as TV or
Projector with an HDMI cable.
6| AUDIO OUT| Audio output port, connect to amplifier or speaker.
7| IR IN| Connect to the IR Receiver cable. The IR signal will send to the IR
OUT port of the transmitter.
8| IR OUT| Connect to the IR blaster cable, the IR signal is from IR IN port
of the transmitter.
9| RS-232| 3-pin Phoenix connector for RS-232 command transmission. The RS-232
command will pass-through from transmitter to receiver or from receiver to
transmitter
IR Pin Definition
EDID Mode
The defined EDID setting list of the product is shown as below:
| EDID Mode | EDID Description |
|---|---|
| 11111 | 1080P, Stereo Audio 2.0 |
| 11110 | 1080P, Dolby/DTS 5.1 |
| 11101 | 1080P, HD Audio 7.1 |
| 11100 | 1080I, Stereo Audio 2.0 |
| 11011 | 1080I, Dolby/DTS 5.1 |
| 11010 | 1080I, HD Audio 7.1 |
| 11001 | 1080P 3D, Stereo Audio 2.0 |
| 11000 | 1080P 3D, Dolby/DTS 5.1 |
| 10111 | 1080P 3D, HD Audio 7.1 |
| 10110 | 4K2K30Hz_444, Stereo Audio 2.0 |
| 10101 | 4K2K30Hz_444, Dolby/DTS 5.1 |
| 10100 | 4K2K30Hz_444, HD Audio 7.1 |
| 10011 | 4K2K60Hz_420, Stereo Audio 2.0 |
| 10010 | 4K2K60Hz_420, Dolby/DTS 5.1 |
| 10001 | 4K2K60Hz_420, HD Audio 7.1 |
| 10000 | 4K2K60Hz_444, Stereo Audio 2.0 |
| 01111 | 4K2K60Hz_444, Dolby/DTS 5.1 |
| 01110 | 4K2K60Hz_444, HD Audio 7.1 |
| 01101 | 4K2K60Hz_444, Stereo Audio 2.0 HDR |
| 01100 | 4K2K60Hz_444, Dolby/DTS 5.1 HDR |
| 01011 | 4K2K60Hz_444, HD Audio 7.1HDR |
| 01010 | COPY_FROM_LOOP OUT |
| 01001 | COPY_FROM_HDBT OUT1 |
| 01000 | COPY_FROM_HDBT OUT2 |
| 00111 | COPY_FROM_HDBT OUT3 |
| 00110 | COPY_FROM_HDBT OUT4 |
| 00101 | 1080P, Stereo Audio 2.0 |
| 00100 | 1080P, Stereo Audio 2.0 |
| 00011 | 1080P, Stereo Audio 2.0 |
| 00010 | 1080P, Stereo Audio 2.0 |
| 00001 | 1080P, Stereo Audio 2.0 |
| 00000 | PC control mode |
ASCII Commands
The product also supports ASCII command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as b
ASCII Commands|
---|---
Serial port protocol. Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check
bit: 0|
x – Parameter 1 y – Parameter 2
! – Delimiter
|
Command Code| Function Description| Example| Feedback|
Default Setting|
Power|
s power z!|
Power on/off the device, z=0~1 (z=0 power off, z=1 power on)
| power 1!| Power on
System Initializing… Initialization Finished! FW version x.xx.xx|
power on
|
r power!| Get current power state| r power!| power on/power off| |
s reboot!| Reboot the device| s reboot!| Reboot…
System Initializing… Initialization Finished! FW version x.xx.xx| |
System Setup| | | | |
help!| List all commands| help!| | |
r type!| Get device model| r type!| HDC-SPB14H150| |
r status!| Get device current status| r status!| Get the unit all status:
power, in/out connection, edid mode| |
r fw version!| Get Firmware version| r fw version!| MCU BOOT: Vx.xx.xx MCU
APP: Vx.xx.xx| |
r link in!| Get the connection status of the input port| r link in!| HDMI IN:
connect| |
r link out y!| Get the connection status of the y output port, y=0~5(0=all,
1~4=HDBT 1~4, 5 = loop out)| r link out 1!| hdmi loop out: connect
hdbt output 1: connect| |
s reset!| Reset to factory defaults| s reset!| Reset to factory defaults
System Initializing… Initialization Finished! FW version x.xx.xx| |
Output Setting|
s hdmi stream z!
| Set hdmi loop output stream on/off z=0~1(0:disable,1:enable)|
s hdmi stream 1 !
| Enable hdmi loop out stream
Disable hdmi loop outstream|
enable
|
s hdmi hdcp z!
| Set hdmi loop output hdcp on/ off
z=0~1(0:disable,1:enable)|
s hdmi hdcp 1!
| Enable hdmi loop out hdcp
Disable hdmi loop outhdcp|
enable
|
s hdbt y hdcp z!| Set hdbt output y hdcp on/off, y=0~4(0=all) z=0~1(0:disable,
1:enable)|
s hdbt 1 hdcp 1 !
s hdbt 0 hdcp 1 !
| Enable hdbt output 1
hdcp
Disable hdbt output 1 hdcp
Enable hdbt all outputs hdcp Disable hdbt all outputs hdcp| enable|
| | | Enable hdbt output 1| |
s hdbt y stream z!
|
Set hdbt output y stream on/ off, y=0~4(0=all) z=0~1 (0:disable,1:enable)
| s hdbt 1 stream 1 !
s hdbt 0 stream 1 !| stream
Disable hdbt output 1 stream
Enable hdbt all outputs stream
Disable hdbt all|
enable
|
| | | outputs stream| |
r hdmi stream!| Get hdmi loop out stream status| r hdmi stream!| Enable hdmi
output stream| |
r hdmi hdcp!| Get hdmi loop out hdcp status| r hdmi hdcp!| Enable hdmi output
hdcp| |
r hdbt y hdcp!| Get hdbt output y hdcp status, y=0~4(0=all)| r hdbt 1 hdcp!|
Enable hdbt output 1 hdcp| |
r hdbt stream!| Get hdbt output y stream status, y=0~4(0=all)| r hdbt 1
stream!| Enable hdbt output 1 stream| |
EDID Setting|
| Set input EDID from default EDID z, z=1~27
1, 1080p,Stereo Audio 2.0
2, 1080p,Dolby/DTS 5.1
3, 1080p,HD Audio 7.1
4, 1080i,Stereo Audio 2.0
5, 1080i,Dolby/DTS 5.1
6, 1080i,HD Audio 7.1
7, 3D,Stereo Audio 2.0
8, 3D,Dolby/DTS 5.1
9, 3D,HD Audio 7.1
10, 4K2K30_444,
Stereo Audio 2.0
11, 4K2K30_444,Dolby/DTS 5.1
12, 4K2K30_444,HD Audio 7.1
13, 4K2K60_420, Stereo Audio 2.0
14, 4K2K60_420,
Dolby/DTS 5.1
15, 4K2K60_420,HD Audio 7.1
16, 4K2K60_444,
Stereo Audio 2.0
17, 4K2K60_444, Dolby/DTS 5.1
18, 4K2K60_444,HD Audio 7.1
19, 4K2K60_444,
Stereo Audio 2.0 HDR 20, 4K2K60_444,
Dolby/DTS 5.1 HDR
21, 4K2K60_444,
HD Audio 7.1 HDR 22, copy from hdmi loop out 23, copy from hdbt output 1
24, copy from hdbt output 2
25, copy from hdbt output 3
26, copy from hdbt output 4 27, use user1 EDID| | input EDID:1080p, Stereo
Audio 2.0| |
s edid in from z!
| s edid in from 1!| | 1080p,Stereo Audio 2.0|
| | Please toggle EDID dip switch to 00000!| |
s edid user1 00
FF FF FF FF …!| Set user1 EDID data| s edid user1 00
ff ff ff ff …. !| user1 EDID data: 00
FF FF ….
| |
r edid user1!
|
Get user1 EDID data
|
r edid user1!
| user1 EDID data : 00 FF FF FF FF FF FF 00 ………| |
r edid in!| Get EDID status of the input| r edid in!| input EDID: 4K2K60_
444,Stereo Audio 2.0| |
r edid in data!| Get the EDID data of the hdmi input| r edid in data!| EDID
data : 00 FF FF
FF FF FF FF 00 ……| |
| RS-232 BYPASS Setting
|
s rs232 bypass hdbt y!
| Set RS-232 port connect to HDBT out1 Receiver RS-232 port, y=0~5( 0=all,
1~4= hdbt out 1~4 5=NC)|
s rs232 bypass hdbt 1!
| RS-232 connect to HDBT OUT1
RS-232 not connect to HDBT OUT|
y=0
| r rs232 bypass!|
Get RS-232 port connect to HDBT out receiver RS-232 port
| r rs232 bypass!| RS-232 connect to HDBT OUT1
RS-232 connect to all HDBT OUT
RS-232 not connectto HDBT OUT|
|
s device baud w size x stop y parity z!
| Set receiver control device COM port setting, w=2400, 4800,9600,19200,38400,
57600,115200, x=7,8
y=1,2, z=none, even,odd| s device baud 57600 size 8
stop 1 parity none!
| receiver device COM port setting baudrate: 57600 data size :8, stop:1
parity: none|
| s rs232 time x!| set send RS232 command wait time
x=200~5000ms| s rs232 time 200!| send RS-232 command wait time 200ms|
200ms
Application Example
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>