NORDIC CW-B0318 18V Impact Wrench User Manual

NORDIC CW-B0318 18V Impact Wrench

Product Information

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions may result in electric shock, fire and/or serious injury.
Keep safety warnings and instructions for future reference.
The term “power tool” in the safety warnings refers to your mains operated (corded) power tool or battery- operated (cordless) power tool.

WORKING AREA

• Keep working area clean and well lit. Untidy and dark areas can lead to accidents.
• Do not operate power tools in potentially explosive surroundings, for example, in the presence of inflammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders at a distance when operating a power tool. Distractions can cause you to lose control of it.

ELECTRICAL SAFETY

• Always check that the power supply corresponds to the voltage on the rating plate.
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce the risk of an electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an increased risk of an electric shock if your body is earthed.
• Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an electric shock.
• Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of an electric shock.
• When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using a cord suitable for outdoor use reduces the risk of an electric shock.
• If operating a power tool in a damp location is unavoidable, use a power supply protected by a residual current device (RCD). Using an RCD reduces the risk of an electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when operating a power tool may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury.
• Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely.
• Remove any adjusting keys or spanners before turning on the power tool. A spanner or key left attached to a rotating part of the power tool may result in personal injury.
• Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable you retain control over the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelery. Keep your hair, clothing and gloves away from the power tool. Loose clothes, jewelery or long hair can become entangled in the moving parts..
• If there are devices for connecting dust extraction and collection facilities, please ensure that they are attached and used correctly. Using such devices can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not expect the power tool to do more than it can. Use the correct power tool for what you want to do. A power tool will achieve better results and be safer if used in the context for which it was designed.
• Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store power tools, when not in use, out of the reach of children and do not allow people who are not familiar with the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused by using poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
• Use the power tool, accessories and cutting tools, etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work which needs to be done. Using a power tool in ways for which it was not intended can lead to potentially hazardous situations.

SERVICE
Your power tool should be serviced by a qualified specialist using only standard spare parts. This will ensure that it meets the required safety standards.

Special safety instructions for wrenches

• Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a ″live″ wire will make exposed metal parts of the tool ″live″ and shock the operator.
• Let bit cool before touching, changing or adjusting it. Bits heat up dramatically while in use, and can burn you.
• Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact your supplier for a replacement.
• Avoid unintentional starting. Prepare to begin work before turning on the tool.
• Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control.
• When using a handheld power tool, maintain a firm grip on the tool with both hands to resist starting torque.
• Do not leave the tool unattended when the Battery Pack is connected. Turn off the tool, and remove the Battery Pack before leaving.

ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS

WARNING: Use only batteries and chargers applicable for this machine.

BATTERIES

• Never attempt to open for any reason.
• Do not store in locations where the temperature may exceed 40 °C.
• Charge only at ambient temperatures between 4 °C and 40 °C.
• When disposing of batteries, follow the instructions given in the section “Protecting the environment”.
• Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal directly or via accidental contact with metallic objects, the battery is short circuited and an intense current will flow causing heat generation which may lead to casing rupture or fire.
• Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators and other polymer components may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat generation causing rupture or file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning may result.
• Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows:
• Carefully wipe the liquid off using a cloth. Avoid skin contact.
• In case of skin or eye contact, follow the instructions below:
  • Immediately rinse with water. Neutralize with a mild acid such as lemon juice or vinegar.
  • In case of eye contact, rinse abundantly with clean water for at least 10 minutes.
  • Consult a physician.

WARNING: Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the battery.

CHARGERS

• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose to water.
• Do not open the charger.
• Do not probe the charger.
• The charger is intended for indoor use only.

SYMBOLS
In this manual and/or on the machine the following symbols are used:

• Denotes risk of personal injury or damage to the tool.
• Read manual before use
• Wear eye protection
• Wear ear protection
• Wear safety gloves
• Wear respiratory protection
• In accordance with essential requirements of the European directive(s)
• Class II – The machine is double insulated; Earthing wire is therefore not necessary (only for charger)
• Ambient temperature 40°C max. (only for battery)
• Do not expose charger and battery pack to water
• Use battery and charger only in closed rooms
• Do not incinerate battery pack or charger

PRODUCT

1. 1/2” chuck
2. Forward/reverse knob
3. Handle
4. Battery pack release button
5. Battery pack (not included)
6. On/off switch trigger
7. LED work light
8. Belt clip

BEFORE YOU START

CHUCK
Your tool has a 1/2” chuck

FORWARD/REVERSE SELECTOR(RIGHT/LEFT ROTATION SELECTOR)
Your tool has a forward/reverse selector located above the switch trigger.
CAUTION: To prevent damage to the gearbox, always allow the chuck to come to a complete stop before changing the direction of rotation or selecting another speed (HI-LO). To stop, release the trigger switch.

VARIABLE SPEED
Your tool has a variable speed switch.
The rotational speed and torque will in-/ decrease equivalently to applied trigger pressure.

LED LIGHT
Your tool is equipped with an LED light at the front.

TPR SOFT GRIP
Your cordless drill is equipped with TPR soft grip and protective parts. TPR (Thermoplastic rubber) is elastic, shock absorbing and environmental friendly (recyclable).

OPERATION

CHARGING THE BATTERY PACK
The battery pack for this tool is supplied in a low charge condition to prevent possible problems, therefore, you have to charge the battery before first use.
Note: Batteries will not reach full charge the first time they are charged. Allow several cycles for the item to fully charge. The battery should only be charged indoors.

After normal use, about 1 hour of charging time is required for the battery to be fully charged. The battery pack will become slightly warm while charging, this is normal and does not indicate a problem.
Do not place the charger in an area of extreme heat or cold. Best is at normal room temperature. When the battery becomes fully charged, unplug your charger from the power supply and remove the battery pack from the charger.
Note:

• Allow the battery pack to cool completely before charging.
• Inspect the battery pack before charging, do not charge a cracked or leaking battery pack.

CHARGING INDICATION (FIG 1)
Connect the charger to the power outlet socket

• Solid green: ready to charge
• Solid red: charging
• Solid green: charged

Note: If the battery does not fit properly, disconnect it and confirm that the battery pack is the correct model for this charger as shown on the specification chart. Do not charge any other battery pack or any battery pack that does not securely fit the charger.

• Frequently monitor the charger and battery pack while connected.
• Unplug the charger and disconnect it from the battery pack when finished.
• Allow the battery pack to cool completely before using it.
• Store the charger and battery pack indoors, out of reach of children.

WARNING:

• Note: If battery is hot after continuous use in the tool, allow it to cool down to room temperature before charging. This will extend the life of your batteries.
• Note : Remove battery pack from charger stand which use your thumb or fingers, press the battery’s release button in and pull the battery pack off at the same time.

BATTERY POWER INDICATOR (FIG 1A)
Those 3 LED might show the status of the capacity level of the battery:

• 3 LED’s are lith: Battery fully charged
• 2 LED’s are lith: Battery 60% charged
• 1 LED is lith: Battery almost discharged

INSERTING AND REMOVING THE BATTERY (FIG.2)

WARNING: Before making any adjustments ensure the drill is switched off with the direction of rotation selector in the centre position.

• Hold the tool with one hand and the battery pack (5) with the other.
• To install : push and slide battery pack into battery port, make sure the release latch on the rear side of the battery snaps into place and battery is secure before beginning operation.
• To remove : Press the battery release latch and pull the battery pack out at the same time.

SELECTING CORRECT SOCKET BIT

• Always use the 1/2in drive socket bits.
• An incorrect size bit will not fit, or will result in inaccurate and inconsistent fastening torque and /or damage to the bolt or nut.

INSTALLING OR REMOVING SOCKET BIT

• To install the socket bit, simply push the 1/2in socket bit over the 1/2in square drive anvil as far as it will go. It will lock into position.
• To remove the driver bit, pull the socket bit off the anvil with force and pull the socket bit off

SWITCH
The impact driver is started and stopped by depressing and releasing the ON/OFF switch trigger.

SWITCH LOCK

• The switch trigger can be locked in the center position.
• This helps to reduce the possibility of accidental starting when not in use.
• To lock the switch trigger, place the direction of rotation selector in the center position.

DIRECTION OF ROTATION (FIG.3)
Direction of rotation is controlled by the direction of rotation selector located above the switch trigger.

CLOCKWISE ROTATION:

Right: To select forward rotation, release the on/off switch and push the forward/reverse lever to the left side of the tool.

ANTICLOCKWISE ROTATION:
Left: To select reverse rotation, push the lever to the right side of the tool.

VARIABLE SPEED

• This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure.
• Speed is controlled by the amount of switch trigger depression.

LED LIGHT : The LED work-light can light prior to motor running if you press the switch lightly, which keep the work area to be lighted for checking clearly at first, and it lights also during your operation.
WARNING: Do not stare directly at the light beam. Never aim the beam at any person or an object other than the work piece. Do not deliberately aim the beam at personnel and ensure that it is not directed towards the eye of a person for longer than 0.25s.

CLEANING AND MAINTENANCE

CLEANING

• Keep the ventilation slots of the machine clean to prevent overheating of the engine.
• Regularly clean the machine housing with a soft cloth, preferably after each use.
• Keep the ventilation slots free from dust and dirt.
• If the dirt does not come off use a soft cloth moistened with soapy water.
• Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

MAINTENANCE
Our machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.

REPAIR
This product does not contain any parts that can be repaired by the consumer. Contact a qualified specialist to have it checked and repaired.

ENVIRONMENT
Should your appliance need replacement after extended use, do not dispose of it with the household refuse, but in an environmentally safe way.
Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycle facilities exist. Check you’re your Local Authority or retailer for recycling advice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>