amphion One18X Studio Monitors Instruction Manual
- September 24, 2024
- amphion
Table of Contents
amphion One18X Studio Monitors
Specifications
- Manufacturer: Amphion Loudspeakers Ltd.
- Model: Studio Monitors
- Warranty: Two years
- Origin: Handmade in Finland
Product Information
Welcome to the world of Amphion monitors where the focus is on delivering truthful sound that allows users to experience music in a pure, emotionally engaging way. The monitors are designed to provide a clean, transparent listening experience that vanishes, leaving only the music. Handmade in Finland, these monitors come with a two-year warranty and are known for their exceptional quality and performance.
Features
- Passive speaker design for improved resolution and transparency.
- Crossover point at 1600 Hz for seamless driver integration and point-source-like behavior.
- Uniformly Directive Dispersion (U/D/D) waveguide for acoustically stable performance in all rooms.
Technical Specifications
- Crossover Point: 1600 Hz
- Waveguide: Fifth generation waveguide for driver integration and even response
- Origin: Handmade in Finland
Instructions
Setup Guide
- Unpack the studio monitors carefully and place them on a stable surface.
- Connect the monitors to your audio interface or amplifier using high-quality cables.
- Position the monitors at ear level and equidistant from your listening position for optimal sound.
Complete Studio Solutions
Amphion offers complete studio solutions that can be further enhanced by
combining the monitors with their Bass Systems for a 3-way full-range system.
Accessories
Check out the range of accessories available for Amphion monitors to
enhance your listening experience and optimize your setup.
FAQ
-
Q: How do I clean my Amphion studio monitors?
A: Use a soft, dry cloth to gently wipe the monitors. Avoid using any liquid or chemical cleaners as they may damage the finish. -
Q: Can I use the studio monitors with any audio interface?
A: Yes, you can connect the studio monitors to any audio interface or amplifier that is compatible with passive speakers.
Studio Monitors
Reference manual
01/2022
Introduction
Welcome
Thank you for choosing Amphion monitors.
“The human sense of sound is exhilarating, yet at the same time, complex.
Trying to understand how we experience sound, and how it affects us, is a
lifelong journey. Some speaker designers focus solely on measurements. For us
the correct measurements are only a starting point in trying to understand how
to convey emotion.
Our job as a speaker manufacturer is to open a large, clean window to music
and allow our customers to experience music in an intimate, touching way –
regardless of their surroundings. The goal is to come up with a pure, highly
transparent, emotionally engaging loudspeaker that will vanish leaving just
the music.
It is humbling that a growing number of the world’s best sound engineers rely
on our products to weave their magic. We will continue our efforts to provide
them with a tool that allows them to focus on bringing the joy of music to as
many people as possible.”
Anssi Hyvönen
Founder & Managing Director, Amphion Loudspeakers Ltd.
Warranty and support
Warranty
Amphion Create products come with a two-year warranty against defects in
materials and our workmanship. For warranty or out-of-warranty service, in the
first instance please contact your original dealer and provide a copy of the
original sales receipt. If you require additional assistance, please contact
your local sales representative or distributor. If you have difficulty making
contact with either of the above, please contact our headquarters. Please do
not return or ship any product to Amphion Loudspeakers Ltd. nor its resellers
without prior authorisation.
Handmade in Finland
Amphion Loudspeakers Ltd. is awarded the right to use the Association for
Finnish Work’s Key Flag Symbol mark of origin. This mark is granted to
Finland-based organizations that manufacture their products in Finland, having
a minimum domestic content of 50 percent.
Company profile
Amphion Loudspeakers Ltd. was established in 1998.
We design and build loudspeakers that are characterised by a high-resolution,
unstrained low-level reproduction and a pure driver integration. Our
affordable solutions are rather insensitive to room acoustics and fill any
space with a wide and even dispersion. A timeless yet flexible approach with
regard to aesthetics and application make Amphion products easy to match with
individual styles and preferences.
All products are handmade in Finland to ensure enduring listening quality.
Follow us
amphion.fi
Social media
www.facebook.com/AmphionLoudspeakers
twitter.com/amphion_fi
www.youtube.com/user/AmphionLoudspeakers
www.instagram.com/amphion_loudspeakers
Philosophy
Hear it all
Your ears are the most important tool in your studio. Providing them with
detailed, reliable information is the only way for making right, stress-free
decisions. Pushing the acoustic design allows us to keep our products
electrically simple, as well as ensure transparency, resolution, and
exceptional time and phase coherence. All products use time-adjusted drivers
and a 1600 Hz tweeter crossover. This leads into point-source-like behavior
and seamless driver integration. Rock-solid “phantom” center, life-like 3D
imaging and an extremely wide and deep sweet-spot are characteristic of all
Amphion products.
Truthful sound
Amphion’s Uniformly Directive Dispersion (U/D/D) allows the speakers to work
in a predictable and acoustically-stable manner in all rooms. Amphion’s fifth
generation waveguide ensures driver integration, eliminates cabinet
diffractions, and produces a uniform and even response throughout a broad
frequency band. The result is a wide, even listening area, which provides
predictable results in your current room as well as your next. Use of a
passive radiator instead of a vent not only makes for a more natural energy
transfer and improved bass definition, but also enhances the midrange clarity.
Work smarter
Achieving more in less time with minimum revisions, while keeping your clients
happy, is a must in today’s world. To achieve this, your monitoring must
translate well and guide you to focus on the essential information. Being able
to totally trust your monitors leads into substantial time savings and peace
of mind – even when working towards the tightest deadlines. All monitor models
can be elevated into perfectly integrated 3-way full-range system by combining
them with our Bass Systems.
Monitors
Front
Rear
Features
-
Passive speaker
Simplicity leads to improved resolution, transparency and longer lifespan. -
Crossover point
All products have time-adjusted drivers with crossovers at a low 1600 Hz. This leads into point-source-like behaviour and seamless driver integration. Rock- solid “phantom” centre, life-like 3D imaging and an extremely wide and deep sweet-spot are characteristic of all Amphion products. -
Waveguide
Amphion’s Uniformly Directive Dispersion (U/D/D) allows the speakers to work in a predictable and acoustically stable manner in all rooms. Amphion’s signature fifth generation waveguide ensures driver integration, eliminates cabinet diffractions and produces a uniform and even response through a broad frequency band. The result is a wide, even listening area, which allows you to trust your monitors in your current room as well as your next. -
Acoustic centre point
The acoustic center point of Amphion monitors is located in the middle of the speakers. In One -series it is between the drivers (under the waveguide, on top of the woofer), which allows them to be used both vertically and horizontally. In Two -series the center point is in the tweeter. We recommend using Two15 and Two18 vertically to avoid any loss in imaging and depth information. Line the acoustic centre point to your ear-level for optimal performance. -
Passive radiator
Eliminating the reflex ports improves bass control. In addition to improving the speed and tonality of bass this creates a more natural energy transfer and enhances midrange clarity. Due to the passive radiator the speaker can be used closer to the walls, which creates more flexibility for speaker placement. -
DSP free
Amphion´s advanced acoustic design and electrical purity allows harnessing the full power of latest monitor controllers, other signal processing devices, as well as room-correction or other types of advanced software. -
Connections
3-way binding post can be used with banana plugs, spades and bare wire.
Technical specifications
- Operating principle Two-way, passive radiator
- Tweeter 25 mm / 1” titanium
- Mid / woofer 12 cm / 4½” aluminium
- Crossover point 1600 Hz
- Impedance 8 Ω
- Sensitivity 84 dB @ 2.83V/1m
- Frequency response 78 – 20 000 Hz +/-3dB
- Power recommendation 50 – 200 W
- Measurements (H x W x D) 259 x 132 x 220 mm
- Weight 5 kg
- Listening Distances ~ 0.5 m – 1.25 m
- Application Home Studio, Small Post-Production Edit Bays, Mobile Trucks, FOH
Measurements
Impedance
Because all real control rooms have at least one surface (a floor) the speaker low end (below 100Hz) is measured in half free space. This gives a fairly accurate estimation of a very large control room, with the speaker placed far from back and side walls. As the room size decreases, the amount of bass increases, which means that the smaller speaker models are particularly well suited to smaller rooms which will support the bass response of the speaker. In other words, the plotted frequency response corresponds to the minimum amount of bass you can expect in any control room.
Frequency response
- Operating principle Two-way, passive radiator
- Tweeter 25 mm / 1” titanium
- Mid / woofer 15 cm / 5¼” aluminium
- Crossover point 1600 Hz
- Impedance 8 Ω
- Sensitivity 84 dB @ 2.83V/1m
- Frequency response 49 – 20 000 Hz +/-3dB
- Power recommendation 50 – 200 W
- Measurements (H x W x D) 316 x 160 x 265 mm
- Weight 7 kg
- Listening Distances ~ 0.75 m – 1.5 m
- Application Home Studio, Project Studio, Commercial Studio
Measurements
Impedance
Because all real control rooms have at least one surface (a floor) the speaker low end (below 100Hz) is measured in half free space. This gives a fairly accurate estimation of a very large control room, with the speaker placed far from back and side walls. As the room size decreases, the amount of bass increases, which means that the smaller speaker models are particularly well suited to smaller rooms which will support the bass response of the speaker. In other words, the plotted frequency response corresponds to the minimum amount of bass you can expect in any control room.
Frequency response
- Operating principle Two-way, passive radiator
- Tweeter 25 mm / 1” titanium
- Mid / woofer 15 cm / 5¼” aluminium
- Crossover point 1600 Hz
- Impedance 8 Ω
- Sensitivity 84 dB @ 2.83V/1m
- Frequency response 49 – 20 000 Hz +/-3dB
- Power recommendation 50 – 200 W
- Measurements (H x W x D) 316 x 160 x 265 mm
- Weight 7 kg
- Listening Distances ~ 0.75 m – 1.5 m
- Application Home Studio, Project Studio, Commercial Studio
Impedance
Because all real control rooms have at least one surface (a floor) the speaker low end (below 100Hz) is measured in half free space. This gives a fairly accurate estimation of a very large control room, with the speaker placed far from back and side walls. As the room size decreases, the amount of bass increases, which means that the smaller speaker models are particularly well suited to smaller rooms which will support the bass response of the speaker. In other words, the plotted frequency response corresponds to the minimum amount of bass you can expect in any control room.
Frequency response
- Operating principle Two-way, passive radiator
- Tweeter 25 mm / 1” titanium
- Mid / woofer 18 cm / 6½” aluminium
- Crossover point 1600 Hz
- Impedance 8 Ω
- Sensitivity 85 dB @ 2.83V/1m
- Frequency response 45 – 20 000 Hz +/-3dB
- Power recommendation 100 – 350 W
- Measurements (H x W x D) 380 x 191 x 305 mm
- Weight 10 kg
- Listening Distances ~ 1.25 m – 2.25 m
- Application Home Studio, Project Studio, Commercial Studio, Broadcast Studio, Small~Large Studios
Impedance
Because all real control rooms have at least one surface (a floor) the speaker low end (below 100Hz) is measured in half free space. This gives a fairly accurate estimation of a very large control room, with the speaker placed far from back and side walls. As the room size decreases, the amount of bass increases, which means that the smaller speaker models are particularly well suited to smaller rooms which will support the bass response of the speaker. In other words, the plotted frequency response corresponds to the minimum amount of bass you can expect in any control room.
Frequency response
- Operating principle Two-way, passive radiators
- Tweeter 25 mm / 1” titanium
- Mid / woofer 15 cm / 5¼” aluminium
- Crossover point 1600 Hz
- Impedance 4 Ω
- Sensitivity 86 dB @ 2.83V/1m
- Frequency response 44 – 20 000 Hz +/-3dB
- Power recommendation 100 – 350 W
- Measurements (H x W x D) 452 x 160 x 265 mm
- Weight 10 kg
- Listening Distances ~ 1.0 m – 1.75 m
- Application Home Studio, Project Studio, Commercial Studio, Broadcast Studio, Medium~Large Studios
Impedance
Because all real control rooms have at least one surface (a floor) the speaker
low end (below 100Hz) is measured in half free space. This gives a fairly
accurate estimation of a very large control room, with the speaker placed far
from back and side walls. As the room size decreases, the amount of bass
increases, which means that the smaller speaker models are particularly well
suited to smaller rooms which will support the bass response of the speaker.
In other words, the plotted frequency response corresponds to the minimum
amount of bass you can expect in any control room.
Frequency response
Instructions
Unpacking
Connecting
Care
Maintenance support
Please contact your local Amphion dealer or sales representative for
additional guidance on cabinet, driver, or radiator maintenance. For more
information, you can also contact Amphion headquarters or our regional offices
in Asia (Japan) and North America (USA).
Setup guide
PLEASE NOTE! Always turn power off before inserting or removing cables.
“Amphion studio monitors are very transparent. Due to this all the pros and cons of the signal chain are revealed. We recommend pairing the monitors with matching Amphion amplifiers and cables, but they work adequately with other products as well.”
Studio-monitor placement
Basic Monitor Setting Video Guide: https://youtu.be/600vjI3YN50
Studio-monitor stencil
Instructions:
- Centre of Template:
- Set Primary Angles:
- Correct Imaging #1 :
- Correct Imaging #2:
- Head/Listening Position
- Monitor(L)— Head* Monitor(R) 11600 Rule”
- Monitors -+ Head + Monitor— Monitor Distance
- Use Tilt + Toe-in for Monitor— Ear Directionality
*Use laser-pen for accurate alignment. Alignment/Angle
Positions:
- Listening Position Location-point
- Front Stereo 30—400 From Centre [LIRI
- 5.1 Surround Sound 100-1200 [LSIRS]
- 6.1 Surround Sound 135-1600 [LSIRS] 1 1800 [B] = Tweeter— Ear
- 7.1 Surround Sound 90-1100 [LSIRS] 1 130-1500 [BLSIBRS]
Complete studio solutions
Power amplifiers
Amphion amplifiers provide abundant, fast, controlled power with low
distortion. After evaluating all the available D-class solutions, suitable
platforms were identified. To reach the needed sonic character and
performance, an in-house designed buffer-stage was added to ensure optimal
impedance matching to complement the merits of D-Class technology. Our amps
are perfect partners to all Amphion monitors and other passive speakers.
Base systems
Making correct decisions regarding the low frequencies is fundamental and
often the hardest part of sound making. Our Bass Extension systems transforms
your 2-way monitor into a cohesive 3-way full-range system and deliver clear,
accurate and dependable low frequency information for making fast, well
translating decisions. The system´s extreme resolution, speed and control make
it easy to pack the maximum energy into your low-end or spot potential
problems before they turn into headaches.
Accessories
Speaker cables
Amphion speaker cables. Specially braided silver coated copper conductor and
chord banana connectors. Available lengths 2.5 m, 3.5 m and 5 m in Black.
Speaker Wire vs Brand
Amphion’s benchmark position on speaker-wire vs brand-name is based on the
principles of physics and sonic delivery. Claims of exotic materials usage,
general brand hype, and exaggerated performance-levels are not genuine
criteria. Reputable cable manufacturers follow the science and practice of
ensuring the following cable performance standards are met whether for
Project, Private, Commercial, or Dolby Atmos studio applications:
Resistance | Conductance | Inductance | Terminations | Build-Quality | Materials
- high-tolerance wire gauge-to-length ratios → SWG, AWG, or IEC 60228 Standards
- high-quality insulation/shielding → prevention of dielectric loss + non-reactive material on wire
- meeting inductive reactance benchmarks → 10m cable length and <1% audible losses
- high-level connectors/materials and build → component QA and assembly QC are met
Wall bracket
Amphion adaptors are available to fit K&M wall brackets, and are suitable for
all Amphion monitors.
Amphion Loudspeakers Ltd.
Telkkistentie 2
70460 Kuopio
Finland
+358 17 2882100
info@amphion.fi
amphion.fi
AE/RMKR/INEN/0122
Documents / Resources
|
amphion One18X Studio
Monitors
[pdf] Instruction Manual
One18X Studio Monitors, One18X, Studio Monitors, Monitors
---|---