Govee Life H7133 Smart Space Heater Pro User Manual

Govee Life H7133 Smart Space Heater Pro

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injuries to persons, and hyperthermia, including the following:

• Read all instructions before using this heater.
  This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) away from the front of the heater and keep them away from the sides and rear.

• Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.

• Always unplug heater when not in use.

• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.

• Do not use outdoors.

• This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

• To disconnect heater, turn controls to off, then remove the plug from the outlet.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.

• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.

• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.

• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injuries to persons.

• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).

• Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that the heater plug fits tightly into the outlet before using. When using the heater, check to make sure the heater plug is not overheating. If necessary, have a qualified electrician check or replace the wall outlet.

• This heater can only be used when the ambient temperature is normal. When the heater detects that the ambient temperature is too high, it will automatically shut down. Please inspect for any objects on or adjacent to the heater that may cause high temperatures.

• For US: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet in only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

• Hyperthermia can result in death. Symptoms of hyperthermia include high body tempera­ture, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.

• To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confined space around infants, or individuals with reduced physical, sensory, or mental capabilities.

SAVE THESE INSTRUCTIONS

Included in the Box

Introduction

Goveelife Smart Space Heater Pro (Two Positions) can be placed vertically or horizontally. You can lay it flat horizontally to distribute air up and down to warm the whole body. Equipped with PTC heating elements, this smart heater can heat up in 3 seconds after it is powered on, bringing you instant warmth and maximum home comfort during cold weather.

Part Names

Controls

Control Knob
Press the control knob to power on or off.
In Auto Mode, rotate clockwise to increase the target temperature and counterclockwise to decrease the target temperature.

Note:

• The fan will continue working for 15 seconds after powering off to clear any residual heat to increase product lifespan.
• Follow the in-app instructions to press the knob when pairing with the app.
• Rotating the control knob will only work in Auto Mode, Timer Mode, or when adjusting the ambient lighting.

Mode Button
Touch to cycle through Heat Setting I, 11, 111, Auto Mode, and Fan Mode.

Timer Button

• Set a timer: After touching the Timer Button, rotating the knob  clockwise within 5 seconds will increase the time by 1 h, while rotating it counterclockwise will decrease the time by 1 h. After that, wait for a while or operate other functions to complete the setup. The timer can be set for a duration of 1 to 24 hours.
• Check current timer: Touch the button, and the screen will display the remaining time (rounded up to the nearest integer). For more accurate details, check the app.
• Turn off the timer: Press and hold the button for 2 seconds to turn off the current timer setting.

Air Deflector and Lock Button

• Air Deflector (adjust the airflow direction): Touch to turn on the air deflector. It will swing back and forth. Touch again to turn off.
• Lock: Touch and hold for 3 seconds to turn the lock on/off. When the lock is on, other buttons will not respond to any touch, preventing children from accidentally changing any settings.

Note:

• For safety reasons, when using the heater horizontally for the first time, the air deflector will be temporarily unavailable.
• CD will flash when any other button is touched to indicate the lock is on.

Ambient Lighting Button
Touch the button to turn on the ambient lighting. Touch the button for 2s to turn off the ambient lighting.

Brightness Adjustment:
After touching the ambient lighting button, rotating the knob clockwise within 5 seconds will increase the brightness by 5%, while rotating it counterclockwise will decrease the brightness by 5%. After that, wait for a while or operate other functions to complete the setup.

Note: Go to Govee Home App for more brightness settings and lighting scenes.

Recovery Button
Press and hold these two buttons simultaneously for 5 seconds until all indicators flash once to restore the heater to factory settings if it cannot function well. Then the heater will disconnect from Wi-Fi and Bluetooth and automatically reboot.

Note: After restoring the heater to factory settings, go to “My Devices” page on the app to delete this heater first, otherwise it cannot be added to the app again.

Indicator Status

| Safety Lock On| Solid White
Safety Lock Triggered| Flashes White|
| Timer is Set| Solid White
Timer is Setting| Flashes White for Ss|
| Air Deflector is Turned On| Solid White
Air Deflector is Initializing| Flashes White|
| Ambient Lighting is On| Solid White
Ambient Lighting is Setting| Flashes White for Ss|
| Wi-Fi is Connected| Solid White
Wi-Fi is Connecting| Quickly Flashes White|
| Displaying Ambient Temperature| Solid White
Target Temperature is Setting| Solid White and Flashes|
| Timer is Setting| Solid White and Flashes
| Wi-Fi Chip is Malfunctioning| Solid White
| Built-in Sensor Failed| Solid White
| Air Deflector Initialization Failed| Solid White

Note: According to related safety standards, the power indicator should always light red when the heater is working.

Functions

Memory Function
This heater will memorize the previous settings (heat settings, air deflection, Wi-Fi connection) when it is powered off. The settings will be active again when this heater is turned on.
24-hour Automatic Shutdown
This heater will shut down automatically when it has been used for 24 hours straight in case the user forgets to power it off.

Overheat Protection
When the heater detects that the ambient temperature exceeds a specific temperature, it will automatically power off.

Tip-over and Motion Protection
When the heater is moved or knocked over, it will automatically power off and stop all functions. This protection can be dismissed by placing the heater on a flat and sturdy surface and keeping it upright before using it again.

Getting Started

1. Remove all packaging and ensure the air inlet and outlet are not blocked by foreign objects.
2. Only plug the heater directly into a 120V wall outlet. Do not use an extension cord.
3. Ensure the power plug is firmly inserted into the outlet. An abnormal outlet connection may cause overheating.
4. Place the heater on a firm, flat, and level surface free from obstructions and at least 3ft (1 meter) away from any wall or combustible materials.
   Note: Do not cover the heater with any cloth or covering, especially over the air inlet and outlet.

Place Horizontally (Optional)

1. If you want to lay the heater flat horizontally to warm your whole body, pull the two built-in stands out.
2. Place the heater on a firm, flat, and level surface free from obstructions and at least 3ft (1 meter) away from any wall or combustible materials.

Note: If the built-in stands are not pulled out properly, the Tip-over Protection will be activated and you will not be able to turn on the heater.

Govee Home App
You can access more features using Govee Home App.

Downloading Govee Home App
To download Govee Home App, scan the QR code or search for “Govee” in the Apple App Store® (iOS) or Google Play Store (Android).

Note:

• Choose “Allow” to the permissions requested when opening Govee Home App for the first time. These permissions allow the app’s features to function normally and are not used to record personal, private information.
• Due to ongoing updates, Govee Home App may be slightly different than shown in this manual. In case of any differences, always follow the in-a pp instructions.

Pairing with Govee Home App

1. Turn on your smartphone’s Bluetooth. Connect to your Wi-Fi router’s 2.4GHz network. 5GHz is not supported.

2. Android users turn on Location Services; 105 users choose Location ->Always On in the pop-up window while adding devices.
   Note:

   • For 105 users, if you chose Location->Never, it might result in notifications/alert excep­tions. It is recommended to follow Settings ->Govee Home ->Location ->Always On to obtain the best experience.
   • Govee Home WILL NOT collect, use, or share your location in any way.

3. Open Govee Home App, tap the”+” icon in the top right corner and search for “H7133.”

4. Tap the device icon and follow the in-app instructions to complete the Bluetooth and Wi-Fi connection.
   Note:

   • Method to turn off Bluetooth and Wi-Fi connection: Press and hold the Ambient Lighting Button and Mode Button for 5s to restore the device to factory settings, then go to “My Devices” page on the app to delete this heater first, otherwise it cannot be added to the app again.

Note:

• You can use Govee Home App to connect your heater to Amazon Alexa or Google Assistant. Follow the in-app instructions to connect to each voice assistant.
• Govee Home App is being continually updated and its features do expand.

Care & Maintenance

Cleaning
To achieve the best performance, clean the heater at least once during the operating season or before storing it when it will not be used for a long period of time.

• Turn the heater off and unplug it from power, then use a soft damp cloth to clean its body, air inlet, and outlet.
• Do not submerge the heater in water and never allow water to drip into it.
• Do not risk your safety to detach the heater to clean its blade. Otherwise, it may damage the heater, shorten its service life, or cause serious danger.

Maintenance
Follow the cleaning instructions and allow all parts to dry completely before storing the heater in a cool, dry place.

Troubleshooting

The troubleshooting section below is for solving frequently asked questions. If your problem persists, please contact Customer Support.

For Smart Space Heater Pro

Problem| Possible Causes| Solution|
---|---|---|---
The heater cannot be turned on.| The power cord is not properly plugged into the outlet.| Plug the power cord into a live outlet.
Unsure how to turn it on.| Press the control knob at the top of the product.|
The power plug is hot.| The power plug and the outlet are not securely connected.| Securely reinsert the plug into the outlet. If necessary, have a qualified electrician to check if the power plug prongs are intact.|
The heater suddenly shuts down when hot air is coming out.| Failed to supply power to the heater.| Ensure your circuit breaker or fuse is working properly.|
| Tip-over Protection has been triggered.| Place the heater on a firm and level surface free from obstructions. Keep it upright and turn it on again.|
| Overheat Protection has been triggered.| Unplug from power and wait for 30 minutes for the heater to cool down before plugging back in. The heater will automatically turn on again when the surrounding temperature is below 86°F (30°C).|
The air deflector is malfunctioning.

The screen displays error code “E2”.

| The structure of the air deflector is manually altered.| Power on and try again.|
| Foreign objects have entered the air deflector system.| Check whether there are any foreign objects in the air deflector. Power on and try again.|
The screen displays “E0” or “E1”.| Product exceptions| Contact Customer Support.|

For App & Connectivity

1. Cannot connect to Govee Home App.
   • Make sure your smartphone is powered on and is not connected with other Bluetooth devices.
   • Enable the smartphone’s Location Services.
   • Try connecting with another smartphone.
   • Make sure your app is updated to the latest version.
   • Make sure you connect to your Wi-Fi router’s 2.4GHz network and that the network is working correctly.
   • Make sure the Wi-Fi password you entered is correct.
   • Shorten the distance between the heater, Wi-Fi router, and the smartphone.
   • Make sure your heater and the Wi-Fi router are located away from appliances that produce electromagnetic radiation (e.g. microwave ovens, refrigerators, etc.)
   • If you are using a VPN, try turning it off and then connecting the heater.
   • Disable portal authentication for your Wi-Fi network. If portal authentication is enabled, this heater will not be able to access your Wi-Fi network, and setup will fail. Portal authentica­tion means that you need to sign in to your Wi-Fi network through a web page before you can use the Internet. 12
2. Cannot find the device on “Bluetooth Device Nearby” page of the app. The heater may be connected with another smartphone. Disconnect it from the other smartphone first.
3. The heater is offline.
   • Make sure the heater is plugged in and powered on, then refresh “My Devices” page in Govee Home App by swiping down on the screen.
   • Make sure your router is connected to the internet, and your smartphone’s network connection is working.
   • If the Wi-Fi password has been changed, the heater will automatically go offline. Try connecting it to the network again.
   • Delete the offline heater from Govee Home App, then add and reconfigure the heater again in the app.

Appendix
After-Sales Service

Warranty: 12-Month Limited Warranty

Support: Lifetime Technical

Email: support@govee.com

Official Website: www.govee.com

@Govee I)

@govee_official

@govee.official

@Goveeofficial

@Govee.smarthome

Specifications

Low: 700W

Deflection Angle| Standing Status: 60 degrees

Lying Status: 40 degrees

Net Weight| 8.26Ibs/3.75kg
Dimensions| 165.4161 567.2mm/6.56.322.3inches

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>