ZKTeco IN710 Fingerprint Reader Device User Guide
- June 12, 2024
- ZKTECO
Table of Contents
- ZKTeco IN710 Fingerprint Reader Device
- Product Information
- Product Usage Instructions
- Overview
- Finger Placement
- Installation Environment
- Device Installation
- Power Connection
- Ethernet Connection
- Type-C Connection
- Door Sensor, Exit Button and Lock Relay Connection
- New User Registration
- Ethernet
- Access Control
- System
- Attendance Record
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZKTeco IN710 Fingerprint Reader Device
Product Information
| Product Name | IN710 |
|---|---|
| Version | 1.2 |
| Dimensions (mm) | 167.00 (W) x 135.00 (H) x 23.50 (D) |
| Features | Microphone, Card Reading Area, Indicator, 5-inch HD |
Touchscreen, Fingerprint Sensor, Speaker, Reset Button
Interface Description| Network Interface, Type-C, 12V Power In, Access Control
Product Usage Instructions
Finger Placement
Recommended fingers: Index, middle, or ring fingers. Avoid using the thumb or
pinky finger, as they are difficult to press accurately on the fingerprint
reader.
Installation Environment
Please refer to the following recommendations for installation:
- Device Installation: The IN710 requires no difficult installation, just fix the device on a flat table.
Power Connection
AC Adapter: DC 12V, 3A
Recommended AC Adapter:
- Rating of 12V and 3A.
- To share the device’s power with other devices, use a power supply with higher current ratings.
Ethernet Connection
After the device is powered on, connect the network connector via the Ethernet
cable.
Type-C Connection
Connect the device and computer via a Type-C cable.
Door Sensor, Exit Button and Lock Relay Connection
Door Sensor and Exit Button:
The system supports Normally Opened Lock and Normally Closed Lock. The NO
LOCK (normally unlocked when power-ON) is connected to ‘NO’ and ‘COM’
terminals, and the NC LOCK (normally locked when power-ON) is connected to
‘NC’ and ‘COM’ terminals. For an example, refer to the below-mentioned NC
Lock:
- Device not sharing power with the lock: +5V, +5V, GND
- Device sharing power with the lock: +5V, +5V, GND
New User Registration
When there is no super administrator set in the device, click on icon > [User
Mgt.] > [New User] to register a new user. The options include entering the
user ID and Name, setting User Role and Verification Mode, registering ID
Card, Fingerprint and Password.
Ethernet
Click on icon > [COMM.] > [Ethernet] to set the network parameters. If the
TCP/IP communication of the device is successful, the icon will be displayed
in the upper right corner of the standby interface.
Access Control
Click on icon > [Access Control] to enter the access control interface and set
relevant parameters of access control.
System
Click on icon > [System] to enter the system interface to set the related
system parameters for optimizing the accessibility of the device.
Attendance Record
Click on icon > [Attendance Search] > [Attendance Record] to enter the
personal record search, input the user ID and select the time range. Then the
corresponding attendance record will be displayed.
Contact Information
ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone: +86 769 – 82109991
Fax: +86 755 – 89602394
Website: www.zkteco.com
Overview
Finger Placement
Recommended fingers: Index, middle, or ring fingers.
Avoid using the thumb or pinky finger, as they are difficult to press
accurately on the fingerprint reader.
Installation Environment
Please refer to the following recommendations for installation:
Device Installation
The IN710 requires no difficult installation, just fix the device on a flat table.
Power Connection
Recommended AC Adapter:
- Rating of 12V and 3A.
- To share the device’s power with other devices, use a power supply with higher current ratings.
Ethernet Connection
After the device is powered on, connect the network connector via the Ethernet cable.
Type-C Connection
Connect the device and computer via a Type-C cable.
Door Sensor, Exit Button and Lock Relay Connection
Door Sensor and Exit Button:
Lock Relay Connection:
The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK
(normally unlocked when power-ON) is connected to ‘NO’ and ‘COM’ terminals,
and the NC LOCK (normally locked when power-ON) is connected to ‘NC’ and ‘COM’
terminals. For an example, refer to the below-mentioned NC Lock:
- Device not sharing power with the lock
- Device sharing power with the lock
New User Registration
When there is no super administrator set in the device, click on to enter the
menu. Add a new user and set User Role to Super Admin, then the system
requests for the administrator’s verification before entering the menu. It is
recommended to register a super administrator initially for security purposes.
Click on icon> [User Mgt.] > [New User] to register a new user. The options
include entering the user ID and Name, setting User Role and Verification
Mode, registering ID Card, Fingerprint and Password.
Ethernet
Click on icon > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface.
Access Control
Click on icon > [Access Control] to enter the access control interface and set relevant parameters of access control.
System
Click on icon > [System] to enter the system interface to set the related system parameters for optimizing the accessibility of the device.
Attendance Record
Click on icon > [Attendance Search] > [Attendance Record] to enter the personal record search, input the user ID and select the time range. Then the corresponding attendance record will be displayed.
ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan,
China.
Phone : +86 769 – 82109991
Fax : +86 755 – 89602394
www.zkteco.com
Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>