WiNDHAGER 10645477 Insect Screen Pleated Door Instruction Manual
- June 13, 2024
- WiNDHAGER
Table of Contents
10645477 Insect Screen Pleated Door
Instruction Manual
10645477 Insect Screen Pleated Door
Retractable pleated door
REQUIRED TOOL
CONTENTS
SPARE PART NO.:
|
---|---
INTRODUCTION
In order to ensure the most seamless assembly possible, read the following
safety information and assembly instructions carefully and keep the manual
handy for future reference.
The manual is part of the product and takes you step by step to the finished
insect screen.
Please include when passing the product on to third parties.
PROPER USE
The product protects the user from flying insects in living areas by attaching the former to window and door frames. Application of the product for other purposes, as well as changes to the product are prohibited and can cause personal injuries, and damage the product. The manufacturer takes no responsibility for ensuing damages to the product as well as general damages through assembly. The product is not intended for commercial use. Use during freezing temperatures can damage the product. It is recommended that the product be opened during windy conditions.
LEGEND
WARNING! The signal word is used for medium risk danger, which, when not
avoided, can lead to death or heavy injury.
ATTENTION! The signal word is used for low risk danger, which, when not
avoided, can lead to light or moderate injury.
SAFETY INSTRUCTIONS
WARNING! Potentially life-threatening risk of injury to children and babies!
The product is not a toy. Never leave your child alone or unattended with the
product. The packaging and contents pose a risk of suffocation, strangulation
and injury. Children are not aware of these dangers. Due to the danger of
falling, only attach the product to windows and doors which can be accessed
from outside without risk. When attaching or removing the product, please
don’t lean out of the window and don’t press against the insect screen from
inside.
ATTENTION! There is a risk of injury through improper assembly and use of
tools. Use work gloves, if necessary. Incomplete assembly kits or damaged
parts may, under no circumstances, be used for assembly. Function and safety
can thus be impacted. Protect the product and any flammable parts from heat
waves and fire.
TECHNICAL DATA
Model: Retractable screen door PLUS 100 x 220 cm
Min. reveal measurements (W x H): 60 x 180 cm
Min. reveal depth : 30 mm
The reveal is defined as the expanse of wall surrounding the door frame.
SCOPE OF DELIVERY
Check the scope of deliver directly after unpacking to ensure everything has been included and there are no faults. Begin the assembly only when you are sure that all parts are present and undamaged. Do not accidentally dispose of assembly materials when disposing of the packaging material.
INSTALLATION
Consider the safety information and follow assembly steps 1 to 15. Use the required tools carefully, to avoid injuring yourself or others. M1 Adhesive mounting M2 Screw mounting
ASSEMBLY VIDEO
An assembly video for the product can be viewed on windhager.eu as well as via QR code (see bottom right).
CLEANING
Clean your insect screen regularly with a damp fibre cloth. Only use mild cleaning products, if required, to avoid damaging the product.
DISPOSAL
Dispose of the packaging material (boxes, foils etc.) separately through a
recycling collection point. The disused product can also be disposed of
through a collection point.
Information on this matter can be obtained from your local authority or city
administration.
MANUFACTURER/SERVICE
Do you have questions on the product or assembly?
Contact us:
FROM GERMANY: 0800 6161 123
germany@windhager.eu
FROM SWITZERLAND: +41 4176 6054-0
swiss@windhager.eu
FROM AUSTRIA: 0800 080 616
austria@windhager.eu
FROM FRANCE: +33 390 6459 79
france@windhager.eu
FAQ
What do I do if the delivery is missing some parts?
Only begin assembling the product when a replacement part has been delivered. If the scope of delivery is missing some parts or contains damaged parts, then you will receive a replacement free of charge. Send us your purchase receipt and article number via email. Should parts be lost or damaged by improper use, then they can be purchased through our spare part and accessory range. Contact us!
The retractable screen is stuck or can no longer be opened or closed?
- Retractable screen and guide rails must be constructed in a right angle to one another. - Strings must be evenly tensioned above and below. - It is possible that a string has been caught when attaching the end caps.
What should I be aware of when cutting?
Shorten the aluminium sections with a metal saw. A mitre box will ensure an exact cut. If necessary, attach the parts which are to be shortened via a screw clamp in the mitre box, without squashing it.
Note: Subject to mistakes, changes and setting errors. Current version of the manual as a PDF download on windhager.eu Date of information 04/2022
OVERVIEW
Measure width B by determining the horizontal wall to clearance
distance. Measure height measurement H of the jamb by determining the vertical
wall to wall distance.
Please note: You will need a jamb depth of min. 30 mm and a contact
surface of 35 mm on each side to install the insect screen.
NB: Please be aware that measurements are in millimetres. 1 cm = 10
mm
Shorten the pleated cassette 1 together with
the guide rail 1a on both sides with a metal saw according to the following
formula: (2202 mm – H)/2. Deduct the height measurement H from the total
length of the pleated door (2202 mm) and divide the result by 2. Mark this
measurement on both sides and shorten the cassette accordingly. Note the
position of the cassette. Example: Measured height of the jamb H = 2000 mm >>>
(2202 mm – 2000 mm)/2 = 101 mm Please note: Risk of injury! Take care when
using the saw. Use a file to deburr the raw edges.
Shorten the two guide rails 2 with a metal saw to the length of
measurement B minus 2 mm. Example: Measured width of the jamb B = 900 mm – 2
mm = 898 mm
Please note: Risk of injury! Take care when using the saw. Use a file to
deburr the raw edges. 
 ASSEMBLY VIDEOhttps://qr.windhager.eu/?art=04552&utm_source=packaging&utm_medium=qr
Guide the strings on both sides along the profile groove to the
end of the handle rail 1a and insert them there. 
Connect the corner connectors 3 and 4 to the cassette 1.
Insert the string guides 4a into the side of the handle rail
1a. 
Place the guide rollers 5 into the recesses
provided on both sides of the string guides 4a. The string will now run
through the guide rollers 5.
Connect the guide rails 2 to the corner connectors 3 and 4 on
the pleated cassette 1.
Connect the corner connectors 6 and 7 to
the guide rails 2. Connect the corner connectors 6 and 7 to the guide rails
and gently pull the string through the corner connectors. 
Clip in the corner connectors 6 and 7 using threaded pins 8.
Use the hexagon socket to do so 8a. 
Tension the string on the
pleated cassette through the connectors 6 and 7 and turn the threaded pin 9
using the hexagon socket 8a to attach the string. Do not over tighten the
threaded pins 9. 
Close the fabric using the handle rails 1a
so that the tabs on the string guides 4 are positioned in the corner
connectors 6 and 7. 
Turn the screw 13 in the recesses in the
corner connectors 6 and 7 so that the tabs are fixed in the string guides 4
for assembly. These screws are removed when assembly is complete and are
intended to make installation easier. 
Position the loop tapes 11 on
the back of the pleated frame. Position the Velcro tapes 12 on top and remove
the protective cover on the Velcro tape 12 just before installation.
The pleated door is ready to be installed.
Remove the protective covers on the Velcro tapes 12 and attach them to the
pleated door on the side of the cassette that is flush with the jamb. Then
remove the two screws 13 and position the covers 9a and 9b on the corner
connectors 6 and 7. OPTIONAL M2: if using a screw mounting system, use a drill
bit (ø 2.5 mm) to drill through the recesses in the four corner connectors in
the door frame and screw the folded door in place with screws 10.
DoP-Nr. 2017-01, DIN EN 13561:2015-08
IS PL 06 00 exterior insect protection system resistance to wind loads: npd
Windhager Handelsgesellschaft m.b.H.
Industriestraße 2, A-5303 Thalgau
+43 6235 6161-0, windhager.eu
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>