Yamaha MT09 Fender Eliminator Kit Tail Tidy Instructions

2021-2023 Yamaha MT-09 Fender Eliminator Kit Standard

Part No. FE-Y21MT09

Parts List

x1 Plate holder
x1 Cover plate
x1 License plate LED light
x1 License plate harness adapter
x6 M6x16mm bolt
x4 M6x30mm bolt
x10 M6 nylon lock nuts
x6 M6 washers
x4 M6 large OD washers
x1 OEM Turn signal brackets (L+R)
x1 Aftermarket signal brackets (pair)
x2 Key hole grommet

Tools:

4mm allen tool
7mm socket (recommended) or wrench
10mm socket (recommended) or wrench
Ratchet with extension
Philips screwdriver

1. Remove seat (key)

2. Remove seat latch bridge bracket (4 bolts using 4 mm allen tool)

3. Locate and unplug the license plate light plug (cylindrical light grey connector)

4. Cut the cable ties securing the license plate light and turn signal harnesses

5. Unplug left and right turn signals plugs (black and white connectors)

6. Remove the rear fender (4 bolts using 10mm sockets from the top and push down on 1 plastic rivet at the forward center of the fender), support fender on last nut and drop down carefully while extracting the left/right turn signal and license plate light harnesses.

7. Pop off the factory yamaha rubber grommet on the under tail opening (just rear of the keyhole)

8. Attach the plate holder to the cover plate using two (2) M16x6mm bolts, M6 washers and M6 lock nuts. Note: cover plate mating surface is the flat side. Pop off the key hole grommet (a spare key hole grommet is supplied with the kit)

9. Attach the LED license plate light to the plate holder by feeding the wires one at at time through the center hole then securing with the 2 washers and nuts using 7mm socket/wrench. Ensure the LEDs are facing down towards the license plate. Attach the license plate light adapter harness White>White and Black>Black then feed the harness up through 1 of the 2 feed wire holes.
   Optional attach OEM or aftermarket turn signals – see below

10. Install back the key hole grommet. While feeding the license plate light wire (and optional turn signals wires up though the under tail, mount the plate holder/cover plate assembly to under tail using four (4) M6x30mm bolts, M6 washers and M6 lock nuts.

11. Connect left/right signals and license plate light plugs, then organize the wires

12. Re-install the seat latch bridge bracket

13. Re-install seat

14. Test all lighting before going on a road test

Attaching OEM signals:

1. Disassembly of the rear fender (4 bolts from the top and 4 screws from the bottom – 4 mm allen tool and Philips screwdriver), separate and extract the turn signals by popping off the plastic lock tab inside the base of the signal, then pop off the signal from the fender along with the wires. The turn signals have a rubber neck extension you can remove to shorten the length of the signals or leave them as is.
2. Remount the turn signals onto the OEM signals brackets included with our kit. You can optionally reverse the left and right signal brackets to shorten the length even more.
3. Mount the turn signal brackets to the back of the plate holder using the four (4) M6x16mm bolts, M6 large OD washers and M6 lock nuts. Bolt>License plate>Plate holder>Signal bracket>Washer>Nut
4. Feed the left and right signal plugs up through key hole grommet hole then position them each into the feed wire holes. Pull up on any slack

Attaching aftermarket signals:

1. Mount the 2 aftermarket turn signal adapters to the plate holder mount upper hole.

2. Mount the aftermarket 8-10mm hole mount turn signals.

3. Run the wires through each of the feed holes and wire it to the bike.

4. Feed wire holes

5. Cover plate

6. Key hole grommet

7. Plate holder

Motodynamic™ copyright © 2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>