EUPHORIA EDSP31-610 31 Band 10 Channel Digital Sound Processor Instruction Manual
- June 13, 2024
- EUPHORIA
Table of Contents
EUPHORIA EDSP31-610 31 Band 10 Channel Digital Sound Processor Instruction Manual
INTRODUCTION
Congratulations on your purchase of a EUPHORIA EDSP31-610. Your selection of a EUPHORIA car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your EUPHORIA DSP in a new system, you are certain to notice immediate performance benefits.
Keep Your Sales Receipt
Take this time to attach your sales receipt to the manual and put in a safe
place. In case of any unforeseen reason this product may need warranty
service, your receipt will be necessary to establish purchase date.
Recommendation
A DSP’s performance is only as good as its installation. Proper installation
will maximize the system’s overall performance. It is recommended that you
have our product installed by an authorized EUPHORIA retailer. However, if you
decide to install it yourself, please carefully read through this manual and
take your time to do a quality installation. Due to continuing product
improvements and possible manual revisions, we recommend checking our website
for latest product information at
www.euphoriacaraudio.com
IMPORTANT!
BEFOR MAKING ANY CONNECTIONS, DISCONNECT THE CAR’S BATTERY UNTIL THE
INSTALLATION IS COMPLATED TO AVOID POSSIBLE DAMAGE TO THE ELECTRICAL SYSTEM.
Serial# __ Model# _____
PRECAUTIONS
Warning:
Do not place the unit in wet or damp places to prevent a short circuit.
Exposure to high power sound system can cause hearing loss or damage.
Listening to your system at loud levels while driving will
impair your ability to hear trace sounds and emergency vehicles.
Use common sense when listening to your system.
Packing List
Every package should include the items below. If there is a shortage of the
items, please get in touch with your retailer and factory.
- EDSP31-610 Unit… ………………… 1PC
- User Manual.. …………………………. 1 PC
- Warranty Card ………………………… 1 PC
- USB Cable ……………………………….. 1 PC
1. About
1.1 EDSP31-610
The Euphoria EDSP31-610 features a sampling rate of 48KHz. The Digital signal processor is a high resolution 170MHz, 64-bit dual floating point (DSP). It features 10 channel digital audio processing, separate gain controls, signal phasing, 31 Band parametric equalization, input, delays, and fully customizable frequency filters with selectable filter slopes.
1.2 Software Computer Screen
PC software control: Please check (2.) for Software operation details
- Automatically detect whatever the hardware is connecting with the USB cable, if ready it will connect with the DSP unit automatically.
- Display resolution over 1280*760, or else the software will not show fully.
- Compatible with Windows system’s computers.
1.3 Specifications
2. Software Settings
2.1 Software Installation
Plug and play PC tuning software.
Operating system compatibility: Suitable for Windows 8-10.
The installation procedure describes:
Simply download the EDSP31-610 software from the website, double-click the
installation le, and follow the on-screen guide. Once installed follow through
with steps 2.2
2.2 PC to EDSP31-610 First Time Connection
The PC to EDSP31-610 connection must be made through a USB cable between the
PC and the EDSP31-610.
Ensure that the EDSP31-610 is powered on and connected with the supplied USB
cable to the computer through the USB interface, the computer will and the new
device and automatically install the equipment, after a few seconds the
installation is
complete. Double-click the EDSP31-610 icon on your PC to open the software.
The main interface is shown in gore 3.2.1. Refer to the status icon in the top
right corner.
Blue is for a successful connection to the PC, and red is for unconnected to
the PC.
2.3 Software
Software interface units are divided into the following sections:
- As shown in figure 3.2.2, “1” (Input Signal Selection)
- As shown in figure 3.2.2, “2” (Connection Status)
- As shown in figure 3.2.2, “3” (Crossover Settings)
- As shown in figure 3.2.2, “4” (Time Delay)
- As shown in figure 3.2.2, “5” (Output Channel EQ Selection)
- As shown in figure 3.2.2, “6” (Equalization Selection)
2.4 Input Source Settings
On figure 3.3.2 “1”, switch the audio input source to the audio input source of your choice.
Optional: High-Level, RCA, wireless streaming. The default audio source can be selected in the option of “1” zone. The default signal source is high level, but users can choose the RCA default signal source while setting up with the PC.
2.5 Output channel switch and operations
*Select the corresponding channel in the “5” section of figure 3.2.2 (CH 1, CH2, CH4, etc.).
You can switch the corresponding channel to adjust relevant parameters when
editing channels. The crossover and equalization will vary depending on the
channel and change in parameter values.
2.6 Output gain, delay, mute and phase setting
Figure 3.3.1 shows 10 output channels commonly used when parameters are
displayed.
The user can adjust the parameters here and customize the drive type of each
output channel.
- The output gain control for each channel can be set independently as well as the master gain.
- Each channel can be muted, and the phase can also be aligned independently. This can be done by selecting the buttons under each channel section.
- Delay selection units are in milliseconds, centimetres, or inches. The range of milliseconds is from 0.000~7.354; the Range of mm is from: 0~254; the Range of inches is from O to 100.
2.7 Output signal equalizer and crossover operation.
Simply drag the slider to adjust the equalizer frequency points; when the mouse is moved to the left and right of the small red box, press and drag left and right to adjust the equalizer Q. All parameters are displayed simultaneously and adjust the current real-time equalizer. The value EQ parameters are also updated.
2.8 Bypass EQ/Restore EQ :
The button shown in Figure 3.3.8, the current channel as long as there is an
equalizer in the open state, this button will appear highlighted in a red
state, indicating that you can click this button to make all the equalizer
bypass. The button will change to
Restore EQ in a white state after that and is ready to “return” back to the
last activated state by clicking on it again.
3. Setting Introductions
Click on the “restore” button to allow all current equalizer channels back to the last activated state.
Note: This operation will change the equalizer gain.
3.1 Reset EQ:
To make all current channel equalizer parameters return to their initial state, select the button shown in Figure 3.3.8. Uniform frequency distribution, Q Value is 7.588, a gain of 0.0dB.
The parameter value of the crossover for the given driver channel or channel
selected is shown in the “frequency selection” column in Figure 3.3.9.
Filter type setting: Drop-down menu to select the type, options are (Linkwitz-
Riley), (Bessel), or (Butterworth).
Frequency setting: You can directly type the input frequency value, select and
scroll with the mouse, or use the up and down keys on your keyboard and other
ways to adjust the low-cut or high-cut frequency.
Slope (slope) settings: 6dB, 12dB, 18dB, 24dB, 30dB, 36dB, 42dB, 48dB per
octave.
3.2 Reset Output Configuration
This button is to re-configure the output signal of the channel type of operation
3.3 Lock output Configuration
Click this button to configure the channels CH7 to CH10 to lock or unlock the operation, it indicates that the configuration settings are locked.
3.4 Memory
Click this ICON to save all system configurations to the PC hard drive or to load a saved PC customized labeled setting.
Preset Buttons 1-6
Right-click/click preset buttons 1-6 to individually save or load 6 fully
customizable DSP settings.
- Computer-stored scene data operation: The amplifier can run in the scene data saved as a computer file or load a previously saved scene computer file.
- Preset 1-6: Right-click preset buttons 1-6 “Load/Save/Delete” item will pop up (Figure 3.4.2)
3.5 Naming Presets:
Select “Save as DSP preset” (Figure 3.4.2) which will bring up a preset naming box (Figure 3.4.4). Enter a name (such as 4-abc) in the preset number you want displayed to save. Select the OK button in Figure 3.4.4 to complete the save as preset.
3.6 Loading presets:
Select the preset you want to load and then click the preset button. A pop-up will appear to indicate the preset is loading, and the loading data window will show you the progress. (Figure 3.4.6)
3.7 Deleting Preset
As shown in figure 3.4.9., right-click the preset #, and select “Delete DSP preset” from the menu to erase a preset setting you do not need.
3.8. Mixer setting :
Select the button on the top left corner of the GUI screen. A pop-up window (Figure 3.4.12) will allow users to route inputs to which outputs they prefer and adjust the input level to each output.
3.9 Saving DSP setting to PC or device
After the EDSP31-610 has been fully configured by the user it is recommended
that the user saves all the to the PC for safekeeping. This can be done by
clicking the memory tab on the top left corner of the GUI screen. When the
pop-up window appears click the Save all presets tab.
This will save all settings on to your PC. Your PC will then ask you to name
the file.
- Speaker I Power I Remote I Dongle
3.9.1 High – level inputs and power connections:
Use the Molex connector to connect your high-level speaker wires from your
factory head-unit. See the diagram below for the configuration
In 1 + Left front
In 1- Left front
In 2 + Right front
In 2 – Right front
In 3 + Left rear
In 3 – Left rear
In 4 + Right rear
In 4 – Right rear
■ +12V connect to 12v positive battery constant power
■ GND connect to chassis ground.
■ REM IN connect to aftermarket head unit REM out wire.
■ REM out connect to aftermarket amplifier or audio accessory requiring
switched turn on.
3.9.2 The REM Out
is triggered either by the High-level audio sensing when using factory radio or the REM In when using aftermarket radio. Make sure to select the appropriate Turn on mode on the EDSP31-610 chassis.
EDSP31-BTD Dongle: An optional Wireless audio streaming and smart phone
control are available. (Sold Separately) the dongle will allow you to stream
audio from your smartphone as well as allow you to use the downloadable
EDSP31-610 DSP control
app. The free apps are compatible with both iOS and Android devices.
Please refer to the Euphoria website for the download links.
www.euphoriacaraudio.com
4. Dimensions
NOTES
EUPHORIA™
LIMITED WARRANTY
Euphoria™ warrants any products purchased in the U.S.A. from an authorized Euphoria™ dealer.
All products are warranted to be free from defects in material and workmanship
under normal use and service for a period of two (2) years.
This warranty applies to the original purchaser only.
Euphoria™ will either repair or replace (as its option) any unit that has been found to be defective and under warranty provided the defect occurs within the two (2) years warranty period.
This limited warranty does not extend to units that have been subjected to
misuse, abuse, neglect, or accident. In Euphoria™ ‘s judgment, products that
show evidence of having been altered, modified, or serviced without Euphoria™
‘s authorization,
will be ineligible under this warranty.
To obtain warranty service please contact your retailer or visit our website at www.euphoriacaraudio.com for more details.
DB Research L.L.P. ■ 302 Hanmore Industrial Parkway ■ Harlingen, TX 78550
Ph: 877-787-0101 ■ Fax:
956-421-4513 ■ tech support:
support@dbdrive.net
DB Drive and Euphoria are Registered Trademarks of DB Research L.L.P.
Designed and Engineered in the U.S.A. ~ Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>