SEALEY APMS01 Premier Modular Storage System Instruction Manual
- June 13, 2024
- SEALEY
Table of Contents
SEALEY APMS01 Premier Modular Storage System
Product Information
The Premier Modular Storage System is a heavy-duty high-end workshop storage system designed to enhance any garage or workshop. It is versatile and durable, with a steel construction that will last for years. The system can easily be adjusted to specific needs, allowing users to purchase a simple base cabinet or create a full workshop storage system. Please read the following instructions carefully to ensure safe and proper usage of the product.
Specifications
Model No| Overall Size (W x D x H)| Small Drawer| Large Drawer| X-Large
Drawer| Full Width Large Drawer
---|---|---|---|---|---
APMS01| 775 x 610 x 955mm| –| –| –| –
APMS02| 1550 x 610 x 955mm| –| –| –| –
APMS03| 775 x 610 x 955mm (x3)| 670 x 535 x 55mm (x2)| 670 x 535 x 130mm (x1)|
670 x 535 x 205mm| –
APMS04| 1550 x 610 x 955mm (x6)| 670 x 535 x 55mm (x2)| 670 x 535 x 130mm
(x2)| 670 x 535 x 205mm (x1)| 1445 x 535 x 125mm
Product Usage Instructions
Safety
- Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these cabinets.
- Locate the cabinets in a suitable work area.
- Keep the work area clean, uncluttered, and ensure there is adequate lighting.
- Use the cabinets on level and solid ground, preferably concrete.
- Keep the cabinets clean and tidy in accordance with good workshop practice.
- Keep children and unauthorized persons away from the work area.
- DO NOT use these cabinets for any purpose other than that for which they are designed.
- DO NOT use the cabinets outdoors.
- DO NOT place the cabinets in a damp or wet location or an area where there is condensation.
- DO NOT clean the cabinets with any solvents which may damage the surfaces or the protective coating.
Assembly
The only assembly required is to fit the worktop supplied separately and the door handles (if applicable).
-
Fit the worktop by screwing from underneath using 4 x hex
flange bolts for standard models or 6 x hex flange bolts for wider models. -
Screw on the handles from the rear using cross head screws.
-
If applicable, remove drawers by pulling them out fully and pushing the black lever in each drawer runner up or down, then pulling out the drawer to release.
Environment Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner compatible with the environment. When the product becomes completelyunserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
- Refer to the instruction manual
- Wear protective gloves
SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these cabinets.
- Locate the cabinets in a suitable work area.
- Keep the work area clean, uncluttered and ensure there is adequate lighting.
- WARNING! Use the cabinets on level and solid ground, preferably concrete.
- Keep the cabinets clean and tidy in accordance with good workshop practice.
- Keep children and unauthorized persons away from the work area.
- DO NOT use these cabinets for any purpose other than that for which they are designed.
- DO NOT use the cabinets outdoors.
- DO NOT place the cabinets in a damp or wet location or an area where there is condensation.
- DO NOT clean the cabinets with any solvents which may damage the surfaces or the protective coating
INTRODUCTION
Heavy-duty high-end Modular Workshop Storage System with an appearance to enhance any garage or workshop. Versatile and durable steel construction that will last for years. Easily adjusts to specific needs; purchase a simple base cabinet or create a full worksh op storage system.
SPECIFICATION
Model No| Overall Size (W x D x H)| Small Drawer| Large Drawer| X-Large
Drawer| Full-Width Large Drawer
---|---|---|---|---|---
APMS01| 775 x 610 x 955mm| –| –| –| –
APMS02| 1550 x 610 x 955mm| –| –| –| –
APMS03| 775 x 610 x 955mm (x3)| 670 x 535 x 55mm (x2)| 670 x 535 x 130mm
(x1)| 670 x 535 x 205mm| –
APMS04| 1550 x 610 x 955mm (x6)| 670 x 535 x 55mm (x2)| 670 x 535 x
130mm (x2)| 670 x 535 x 205mm (x1)| 1445 x 535 x 125mm
Pictured with top fitted, supplied
separately.
ASSEMBLY
-
FIT WORKTOP
The only assembly required is to fit the worktop supplied separately and the door handles (if applicable).
Fit the worktop by screwing from underneath using 4 x hex flange bolts (see Fig. 1) or 6 x hex flange bolts for 60” wide models (see Fig. 2). -
FIT HANDLES
Handles screw on from the rear, using cross-head screws (see Fig. 2). -
REMOVE DRAWERS (if applicable)
Pull the drawer out fully and push the black lever in each drawer runner up or down, then pull out the drawer to release (see Fig. 1).
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
Note : It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important : No Liability is accepted for incorrect use of this product.
Warranty : The guarantee is 12 months from the purchase date, proof of
which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
- 01284 757500
- [email protected]
- www.sealey.co.uk
Limited APMS01, APMS02, APMS03, APMS04 Issue 4 (H,2,3,F) 17/05/23