tuya DI-VC3F Smart Video Intercom Access User Manual

tuya DI-VC3F Smart Video Intercom Access

Introduction

The device is Touch Key Access Controller with WiFi-enabled Intercom. People can install the APP for intercom with their smartphone. and program the access controller by touch key. It is compatible with both iOS (7.0 above) and Android (4.3 above).

Features

Intercom

• 2.4GWiFi connection
• Android and iOS are available
• Full duplex voice intercom
• 2MP+wide angle camera and night vision
• Support TF card with unlimited capacity
• Support motion d9l&ciion. playback, take picture video, unlock remotely

Access Control

• Touch key with one relay, 1000 users (988 common+2 panic+10 visitors)
• Fingerprint version support 100 fingerprint users
• PIN Length; 4-6 digits
• EM card, Mifare card optional
• Wiegand 26-44 bits input & output
• can be used as Wiegand reader with LED & buzzer
• User data can be transferred
• 2 devices can be interlocked for 2 doors

SPECIFICATION

Carton Inventory

Installation

• Remove the back cover from the unit
• Drill 2 holes(A,C) on the wall for the screws and one hole for the cable
• Knock the supplied rubber bungs to the screw holes(A,C)
• Fix the back cover mllly on the wall with 4 flat head screws > Thread the cable through the cable hole(B)
• Attach the unit to lhe back cover

Wiring

Sound and Light Indication

APP Operation

Hare is just a row of steps to get you started.

1. Free APP Downloading
2. Makasu”‘ WiFi works on your mobile phone

Register & Login
(Make sure the registered email is legal and valid, so that you can recover your password once forgotten. Mobile Number is for China Mobile ONLY)

You will get a verification code in your mail box.

Add Device

You can add device by clicking ‘Add Device’ or clicking ‘+’ on the top. Before Adding the device, please make sure it is in adding mode (Door bell LED flashs slowly).

Note : To better manage the devices and family members, you will need to create a HOME before you begin to manage this device.

Operation

1. Revise device name and location
2. Check IP address, ID and time zone of device
3. Configure one or more devices’ automation
4. Door bell LED ON/OFF; Flip screen
5. Adjust device volume
6. Motion detection ON/OFF, set the detection sensitivity, set alarm timer
7. Check the capacity (Total/Used/Remaining) of TF card, and format TF card
8. Value-added Service
9. If turn on it, a notification will be sent after device stayed offline in 30 minutes.
10. Check the FAQ related to device
11. Share the device by Tuya account, message, email, or chat APPs. (Shared Users can’t unlock the door and set the device, only Family Members can unlock the door.)
12. Add a shortcut to your home screen.
13. Restart the device
14. Remove the device

Intercom Calling and Motion Detection

The APP is online when intercom calling

The mobile is on standby when intercom calling or detecting the motion

1. Click the “You have a visitor” message on the intercom interface
2. Click the “Motion detected” message into the alarm record interface

Note: There are two ways to check the alarm record

1. Click the Message button in the intercom interface
2. Check in the Message Center

Keypad Operation

Basic Configure:

Standalone/Controller Mode

Connection Diagram
Common Power Supply

Attention:
Install a 1N4004 or equivalent diode is needed when use a common power supply, or the keypad might be damaged. (1N4004 is included in the packing)

Access Control Power Supply

Users Management

Tips for PIN Security (Only valid for 6 digits PIN):

• For higher security we allow you to hide your correct PIN with other numbers up to a max of 10 digits.
  Example PIN: 123434

• You could use (123434) or * (123434) (“” can be any numbers from 0~9)

Set Access Mode (for without fingerprint version):

Set Access Mode (for fingerprint version):

Operation Setting:

Note : For connecting the Wiegand reader with 32, 40 bits input, need to disable parity bits

Master Card/ Fingerprint Usage (Master / User Fingerprints for fingerprint version only)

Users Operation & Reset to Factory Default

• Open the door: Read valid user card or input a valid user PIN # or input a valid user fingerprint (for Fingerprint Version)
• Remove Alarm: Enter Master Code # or Master Card or valid user card / PIN
• To reset to factory default & Add Master Card: Power off, press the Exit Button, hold it and power on, there will be two beeps, then release the exit button, the LED light turns into yellow, then read any 125KHz EM card /13.56MHz Mifare card, the LED will turn into red, means reset to factory default successfully. Of the card reading, it is the Master Card.

Remarks:

• If no Master Card added, must press the Exit Button for at least 5 seconds before release.(this will make the previous registered Master Card invalid
• Reset to factory default, the user’s information is still retained.

To reset the WiFi System: Power on, press the bell button in 30s, hold it about 5s, until we hear the voice “System Reset”, means reset system successfully, then release the button.

Remarks:
Reset the WiFi System can’t unbind the device, it must be operated in APP to unbind the device.

Wiegand Reader Mode

Connection Diagram

Set Wiegang Output:

Note : For connecting Wiegand controller with 32, 40 bits input, need disable parity bits

Advanced Application

User Information Transfer (Valid for Card / PIN Users)
The device supports the User Information Transfer function, and the enrolled user (cards, PINs) can be transferred from one (let’s name it Master Unit) to another (let’s name it Accept Unit).

Connection Diagram:

Interlock
Remarks: The Door Contact must be installed and connected as the diagram. Let’s name the two Devices as “A “and “B” for two doors “1” and “2”

Connection Diagram:

If enable interlock, when and only door 2 is closed, the user can read the valid fingerprint/ card or input PIN on Reader A, door will open; then when and only door 1 closed,read valid fingerprint/card or input PIN on Reader B, door 2 will open.

Advanced Setting:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>