Network Technologies Inc NTI MONTEST-HD4K-PTBLC Mini 4K 60Hz HDMI Video Test Pattern Generator Analyzer Emulator User Manual
- June 13, 2024
- Network Technologies Inc NTI
Table of Contents
MONTEST-HD4K-
PTBLC
Mini 4K 60Hz HDMI Video Test Pattern
Generator/Analyzer/Emulator
User Manual
MONTEST-HD4K-PTBLC Mini 4K 60Hz HDMI Video Test Pattern Generator
Analyzer Emulator
TRADEMARK
The NTI logo is a registered trademark of Network Technologies Inc in the U.S.
and other countries. All other brand names and trademarks or registered
trademarks are the property of their respective owners.
COPYRIGHT
Copyright© 2023 by Network Technologies Inc. All rights reserved. No part of
this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written consent of
Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
CHANGES
The material in this guide is for information only and is subject to change
without notice. Network Technologies Inc reserves the right to make changes in
the product design without reservation and without notification to its users.
Introduction
The MONTEST-HD4K-PTBLC Mini 4K Ultra-HD Video Test Pattern Generator/Analyzer/Emulator generates video test patterns for evaluating and testing HDMI displays and components up to 4Kx2K @60Hz (4:4:4). HDMI signal status (TMDS/5V) and HDCP analysis are supported, along with EDID emulation.
Features
-
Two modes of operation – HDMI signal generator or display emulator (signal analyzer)
o Generates four test patterns and features four built-in resolutions.-
Resolutions supported: 3840×2160 @60Hz 4:4:4; 3840×2160 @60Hz 4:2:0; 3840×2160 @30Hz
4:4:4; 1920x1080p @60Hz
o Emulation mode provides EDID to the HDMI source device from the emulator’s internal memory. -
Supports headless operation – no monitor attached to source.
-
Use to analyze the HDCP version and signal status (TMDS, 5V) of the video input.
-
Supports resolutions up to 4Kx2K (4096×2160 and 3840×2160) @60Hz 4:4:4.
-
-
HDCP v1.4 and v2.2 analysis.
-
4-pin DIP switch for setting video resolution and HDCP version.
-
LED indicators provide TMDS/5V signal and HDCP status information.
-
Portable, compact design.
-
Ideal for many applications, including: installer/integrator diagnostic test tool; HDMI source and sink testing; thirdparty equipment setup; HDCP compliance verification; production testing; R&D design and testing; and remote desktop access to a headless computer.
Materials Included:
- 1x MONTEST-HD4K-PTBLC Mini 4k Ultra-HD Test Pattern Generator
- 1x USB Power Cable
- 1x Brown Cloth Bag
- 1x URL slip with path to this manual
Materials NOT supplied but available:
HDMI-FF — HDMI Gender Changer, Female-to-Female
HD4K-5-MF — 4K 18Gbps HDMI Extension Cable
Cables can be purchased from Network Technologies Inc by calling
800-742-8324 (800-RGB-TECH) in the US
and Canada or 330-562-7070 (worldwide).
Features 
- HDMI OUT: Connects to HDMI display device. The MONTEST is used as a HDMI signal generator to output HDMI signal.
- HDMI IN: Connects to HDMI source device. The MONTEST is used as a display emulator to detect the HDCP content and signal status (5V, TMDS) of HDMI source.
- SIG LED: When the MONTEST is used as an HDMI signal generator the LED turns red when there is HDMI signal output. When the MONTEST is used as a display emulator, the LED turns green when only 5V signal is detected, or turns red when 5V and TMDS signals are detected simultaneously, or OFF when there is no HDMI signal input.
- HDCP LED: When the MONTEST is used as an HDMI signal generator, the HDCP content can be selected using the 4pin DIP switch. The LED turns green when HDCP2.2 is selected, red when HDCP1.4 is selected, and OFF when there is no HDCP.When the MONTEST is used as a display emulator, the LED turns green when the HDCP content of the HDMI sources is HDCP2.2 compliant, or red when it is HDCP1.4 compliant, or OFF when not HDCP compliant.
- POWER: Micro USB port for power cord connection. The MONTEST must be powered ON when it is used as a signal generator. When the MONTEST is used as a display emulator, it can be powered by HDMI source, so the power cord connection is not required. If the HDMI source does not have enough power, both the SIG LED and HDCP LED will blink.
- DIP SWITCH: When the MONTEST is used as a HDMI signal generator, switches 1 & 2 are used for built-in EDID (video) selection, and switches 3 & 4 are used for HDCP content selection.
There are four DIP switches (1~4). The switch represents “0” when in the lower position, and it represents “1” while the switch in the upper position.
Switch Status (1 &2)| EDID|
---|---|---
00| 4K@60Hz 4:4:4, 2CH PCM
01| 4K@6OHz 4:2:0. 2CH PCM
10| 4K@30Hz 4:4:4, 2CH PCM
11| 1080p@60Hz/3D, 2CH PCM
Switch Status (3 & 4)| HDCP| TestPattern
00| HDCP 2.2| Red Screen
01| HDCP 1.4| Green Screen
10| HDCP OFF| Blue Screen
11| HDCP OFF| White/Black Checkered
Application Examples
Specifications
Video/Audio
- Male HDMI connectors for input and output.
- HDMI 2.0 (up to 4K@60Hz 4:4:4) compliant.
- HDCP 1.4 and 2.2 compliant.
- Resolutions supported:
- Signal generator mode: 3840×2160 @60Hz 4:4:4; 3840×2160 @60Hz 4:2:0; 3840×2160 @30Hz 4:4:4; 1920x1080p @60Hz
- Emulation mode: 4Kx2K resolutions up to 4096×2160 and 3840×2160 @60Hz 4:4:4, HDTV resolutions to 1080p @60Hz, and up to 1920×1200 @60Hz (WUXGA).
- Video bandwidth: 600MHz (18 Gbps)
- Supports embedded digital audio.
Power
- Signal generator mode: USB powered using micro USB port (5V/1A).
- 3.4-ft USB Type A to USB Micro-B male-to-male cable included.
- Display emulation mode: Powered by HDMI source.
Environmental
- Operating temperature: 23 to 131°F (-5 to 55°C).
- Storage temperature: -13 to 158°F (-25 to 70°C).
- Operating and storage relative humidity: 10 to 90% non-condensing RH.
Dimensions
WxDxH (in): 2.95×0.87×0.75 (75x22x19 mm)
Regulatory Approvals
CE, FCC, RoHS
Warranty
The warranty period on this product (parts and labor) is two (2) years from
the date of purchase. Please contact Network Technologies Inc at
800-742-8324 (800-RGB-TECH) or
330-562-7070 or visit our website at
http://www.networktechinc.com for information regarding repairs and/or
returns. A return authorization number is required for all repairs/returns.
NTI MAN434 REV
5/30/23
1275 Danner Dr
Tel: 330-562-7070
Fax: 330-562-1999
Aurora, OH 44202
www.networktechinc.com
References
- NTI Network Technologies Inc Environment Monitoring HDMI Extender
- NTI Network Technologies Inc Environment Monitoring HDMI Extender
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>