Wicked Audio GROWL Rugged Wireless Speaker WI-BTS70 User Manual

: June 13, 2024
: WICKED AUDIO

Wicked Audio GROWL Rugged Wireless Speaker WI-BTS70

Wicked Audio GROWL WI-BTS70

USER MANUAL

In the box

Growl Rugged Wireless Speaker
Travel Carabiner
USB to USB-C Charging Cable
Aux Cable
Instruction Booklet

In the box

FUNCTION

Front LED Light

Solid Red	Charging
Solid Blue	Fully charged
Solid Blue	Bluetooth paired Incoming call On a call
Flashing Blue	Pairing mode Disconnected Bluetooth play mode

Back LED Light

Solid Blue	DC Out (USB Port) is being used for powerbank function

First Time Use

1 – Make sure Growl Wireless Speaker is charged.
2 – Turn on Growl by holding down the power button for 3 seconds 3 – LED on the front of the speaker will ﬂash blue
4 – Your device will detect the pairing name “Wicked Growl.” Select “Wicked Growl” on your device to start pairing your device to the speaker.
5 – Speaker will make a “ding” sound and the blue LED will be SOLID when connected and paired with your device.
6 – You’re ready to go!

Turning on/off speaker

Hold down power button for 3 seconds to turn on your speaker. Hold down power button for 4 seconds to turn off the speaker. You will hear a “growl” sound as the speaker powers off.

Disconnected

When out of range, or if your device becomes disconnect-ed from the speaker, the speaker will make a “growl” sound. Front LED will begin to ﬂash blue.

Incoming Call / Answer / Hangup

When receiving an incoming call, the speaker will detect the device’s programmed ringtone (this may differ depending on your device.) You can answer by using a short press on the Call/Pause/Play button on the top of the speaker.

Low Batteries

Please consider charging your speaker regularly when not in use to retain ample battery life. When the speaker has approximately 10% battery life, the speaker will make a “low charge” sound, indicating the battery is needing to be charged. The speaker will make this announcement 1-2 more times before the battery dies and the speaker shuts off.

CHARGING

Power Bank

Charging External devices with The Growl Speaker External devices like phones or other small electronics that can charge via USB, can be plugged into the USB port on the back of your speaker. Using the device’s charging cord, plug in the USB side of the cable into the USB port on the back of the speaker. If your device requires a cable other than the included USB to USB-C cable, you may substitute another cable that has a USB plug. The speaker does not need to be turned on to use this function. A blue LED will show in the top right corner near the USB port when the power bank function is in use.

Charging Speaker

Plug the USB end of the charging cable into a power supply; then plug the USB-C end of the charging cable into the USB-C port on the back of the speaker.

Linkable Tech

Linking two Growl speakers together

1 – Turn on both speakers. They will go into pairing mode.
2 – When both speakers’ LEDs are ﬂashing blue, DOUBLE PRESS the pause/play button on one speaker. Speaker will beep.
3 – Wait 5-10 seconds. The speaker that was double pressed will continue ﬂashing blue. The other speaker will change to solid blue.
4 – Pair your device to the speaker.
5 – You’re ready to go!

Note: If you have paired a single speaker to your phone or device previously, you must forget the Growl speaker from list of recognized Bluetooth devices before syncing two Growl speakers.

PRECAUTIONS

LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE.
Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced hearing loss
(NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound pressure levels before hearing damage occurs.

SAFE USE & HAZARD WARNINGS

90 dB SPL at 8 hours| 95 dB SPL at 4 hours| 100 dB SPL at 2 hours| 105 dB SPL at 1 hours
---|---|---|---
110 dB SPL at 30 min| 115 dB SPL at 15 min| 120 dB SPL: Avoid as damage may occur

IMPORTANT SAFETY INSTRUCTION

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings
4. Follow all instructions.

Attention should be drawn to the environmental aspects of battery disposal;The use of apparatus in moderate climates

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.