Knightsbridge FLN10 FLN Series Outdoor LED Floodlight Instruction Manual

Knightsbridge FLN10 FLN Series Outdoor LED Floodlight Instruction Manual

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for future reference and maintenance. These instructions should be used to aid installation of the following products: FLN10 / FLN20 / FLN30 / FLN50 / FLNMIC / FLNPIR

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this product is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Do not overload this accessory or subject it to conditions outside its rating
• The FLNxx fittings are Class I and must be earthed
• This FLNMIC and FLNPIR accessories are Class II double insulated
• This product series is IP65 rated

Installation

Note – Microwave sensors may not be suitable for all installations, for exarmple enclosed spaces, as they are able to detect movement through non- metallc surfaces like plasterboard and thin doors. Both sensors can be falsely triggered by changes in temperature, therefore should not be installed near sources of heat such as boller flues.

• Provide power to the required point of installaton refer to BS7671 for correct cabling methods). Suitable |P rated junction boxes should be used where required

• Round cable should be used for the mains supply, with an outer diameter of 5-7.4mm and a CSA of up to 1.5mme, The use of flat cable will cause water ingress to the fitting. A drip loop should be left o the incoming cable

• Using the bracket as a template, mark the location for, and dril the fiing holes ensuring ot to irfinge with any gas/water pipes or electrial cables. This can be done without removing the bracket from the fttng (see Fig. 1)
  

• ix the luminaire to suitable sold surface using the vl plugs and screws provided

• Tilt 50 the cable entry points are accessible

• Unscrew the sealing nut from the compression gland (see Fig. 2) and fit it over the supply cable nscrew the main body of the compression gland from the fiting ensuring that the hexagonal lock ring is ot dilodged (see Fig. 2)
  

• Remove the protective insert from the compression gland, leaving the rubber gasket in place (see Fig. 2), and pass the supply cable through the compression gland

• Prepare the supply cable s shown by stripping back the outer sheath and basic insulation to the correct length (see Fig. 3)
  

• Connect the supply cable ensuring the correct polarity s observed: L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). Please be aware that undue puling or rotating of the termination block will cause damage to the fitting

• Tighten the compression gland and sealing nut ensuring a tight seal is made. Do not overtighten

• Tiltthe fitting to the desired angle and tighten the nuts on the sde

• Switch on and check for correct operation

PIR / MICROWAVE SENSOR ACCESSORY

• Isolate the mains supply to the fitting

• Remove the capping nut, and wsing piyers pull out the protective insert from the fitting & ” (see Fig. 4)
  

• lign the pins on the sensor, push onto the fitting, and tighten ensuring good seal s made. Do ot overtighten

• The rotation and tilt f both sensors can be adjusted once ftted. For the PIR accessory, please ensure it i positioned with the adjustment dials at the bottom

• With the LUX set to Daytime, and the TIME set to the mirimum, perform a walk test to set the SENS setting so the required detection area is covered. Then set the TIME and LUX controls to the desired settings:

Maximurm: upto 10
LUX| Minimurm: 3 lux/ Maximur: 2000 lux| inimum: 10 L/ Maximurn: 2000 lux
TIME| Minimum: 10 sec / Maximurn: 15 min| Minimum: Masirmum: 7 min

Override Function (FLNPIR only)

• Switch the mains supply to the fitting OFF-ON-OFF-ON within three seconds. The light flashes ON-OFF-ON to indicate that it i in override mode. To return to automatic mode, Switch the mains supply to the fitting of o at least 10 seconds, then switch on again
• The FLNMIC has no override function

WARNING
“This product must be disconnected from the drcut if subjected to ary high voltage or insulation resistance testing. Irreparable damage will occur i this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D (FLN10, FLN20)/ E {FLN30, FLN50) to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095. ‘This product cortains a non-replaceable LED light source and a non- replaceable control gear.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm  water only, do not use aggressive cleaning products or solverts which may damage the product. Do not use ary source of high-pressure washers to maintain or clean this lumiaire. “This product is non-dimmable, “This product should be dismantled for disposal when it reaches the end of it Ife. Please website for dismantiing instruction: “This product should be recycled in the correct manner when it reaches the end of it lfe. Check local authorites for where faciites exit.

WARRANTY

This product has a warranty of 3 years from date of purchase. Failuree to install this product in accordance with the current editon of the IEE Wiring Reguiations (BS767), improper use, or removal of the batch code will invalidate the warranty. I this product should fai within its warranty period, it should be returned to the place of purchase for a free of charge replacemert. ML Accessories does not accept responsbilty for any instaliation cated with the replacement product, Your statutory rights are rot affected. ML ries reserve the right to ater product specification without prior notice.

SUPPLIED BY: (UK) MANUFACTURER ML ACCESSORIES LTD, UNIT E CHILTERN PARK, BOSCOMBE ROAD, DUNSTABLE LUS 4LT, WWW.MLACCESSORIES., ouK

(EU) AUTHORISED REPRESENTATIVE SLV LIGHTING GROUP, ML Accessories Limited LUS 4LT DAIMLERSTRASSE 21-23,
‘www.mlaccessories.co.uk 52531 UBACH-PALENBERG, GERMANY EMAIL: EPREL@GROURSLY.COM

Manufacturers Declaration of Conformity For ML Accessories (Knightsbridge) Electrical products n accordance with UKCA marking

ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation

UKCA marking legislation
UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021

Included Legislation
UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE

Safety Standards
Full individual declarations and specific safety standards applicable to relevant product series can be found on our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications. The products comply with all essential requirements of the directives.

Scott Brewer
Head of Technical

Catherine Connolly
CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation

CE marking legislation

In Accordance with the following Directives:
2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive

Including Legislation
1907/2006 REACH
2015/863 RoHS
2021/341 ERP

Safety Standards
Full individual declarations and specific safety standards applicable to relevant product series can be found on our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications. The product complies with all essential requirements of the directives.

Scott Brewer
Technical Manager

Catherine Connolly
CEO

 ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

References

• SLV - Erlebe Licht.
• ML Accessories

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>