PreSonus Eris Sub 8BT Active Studio Subwoofer User Guide

PreSonus Eris Sub 8BT Active Studio Subwoofer User Guide

Introduction

Thank you for purchasing the PreSonus® Eris® Sub 8BT active studio subwoofer. The Eris Sub 8BT lets you take charge of the low-frequency foundation of your mix with a combination of quality components and design, plenty of inputs and outputs, and extensive user controls. Powerful and musical, the Eris Sub 8BT complements full-range monitors without overshadowing them.

This Quick Start Guide provides an overview of the Eris Sub 8BT features, along with basic setup instructions. Register your Eris Sub 8BT to get your manual. Visit my.presonus.com and create or log into your MyPreSonus user account to manage all your PreSonus hardware and software registrations, connect with Tech Support, and more. You can also register using the MyPreSonus app on your mobile device.

What’s in the Box

Hookup

Your Eris Sub 8BT features all the connections and controls needed to use it as the central hub for your monitor system. The onboard high- and lowpass filters let you dial in the correct crossover frequency for your full-range monitors.

Set the Low Pass Filter to 80 Hz and listen to your full system, experimenting with the Low Pass frequency until you system has the most linear response.

Power User Tip : Complete calibration instructions can be found in the Eris Sub 8BT User Manual on the
PreSonus website at www.PreSonus.com.

CAUTION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

POWER

Ac Select

You can pair an additional device, by repeating steps 6-8, and this second pairing will be stored along with the first one.

Note: Audio can only be streamed from one Bluetooth device at a time.

Power User Tip: The next time you switch on your Eris monitors, your stored devices will automatically be paired when powered up.

Connections and Controls

1. Input Gain. Sets the level of the input signal before it is amplified.

2. Low Pass Filter. Sets the upper end of the frequency range reproduced by the Eris Sub 8BT. If you enabled the onboard High Pass Filter, set this control to 80 Hz. Otherwise, set the Low Pass Filter to the lowest frequency that your main monitors can reliably reproduce.

3. TRS Inputs. Balanced 1/4” TRS line-level inputs.

4. RCA Inputs. Unbalanced RCA line-level inputs.
   Note: When both connections are in use, the RCA inputs will sum into the balanced TRS connections.

5. Bluetooth Button. Pressing this button starts the pairing process.

6. Standby used to engage/disengage a power save mode that adheres to the EU Energy Efficient Products Directive to conserve energy when not in use.

7. Polarity. Reverse the polarity of the summed input signal. Power User Tip: Once you have connected your Eris Sub 8BT to your system, try experimenting with each setting while listening to your favorite music. Leave this switch in the position where the bass was the loudest.

8. High Pass Filter. Removes frequency content below 80 Hz from the full-range signal sent form the Eris Sub 8BT outputs. This is useful if your main studio monitors do not provide an onboard high pass filter.

9. TRS Outputs. Balanced 1/4” TRS line-level outputs.

10. RCA Outputs. Unbalanced RCA line-level outputs. 11. Power Switch. This is the On/Off switch, the power status is indicated by the illuminated logo on the front of the cabinet.

11. AC Select Switch. The input-power voltage is set at the factory to correspond with the country to which it was shipped. You should only change the setting if you’re using your Temblor Eris Sub 8BT in a country that uses a different standard voltage.

12. IEC Power Connection. Eris Sub 8BT accepts a standard IEC connection.

Hookup Diagrams

Technical Specifications

Performance:

• Frequency Response:. . . . . . . . . . . 30 Hz to 200 Hz
• Low Pass Filter Frequency: . . . . . . 50 – 130 Hz (variable)
• Signal-to-Noise Ratio: . . . . . . . . . >95 dB
• THD: . . . . . . . . . . . . . . . . . . . . 0.05% @power <160W
• Amplifier Power:. . . . . . . . . . . . . . 50W RMS / 110W Peak
• Amplifier Type: . . . . . . . . . . . . . Class AB
• Peak SPL at 1M: . . . . . . . . . . . . . . 110 dB
• Driver: . . . . . . . . . . . . . . . . . . . . 8”

Size (HxWxD)
11.6” (295 mm) x 9.84” (250 mm) x 12.75” (324 mm)

Power
100-120V ~50/60 Hz or 220-240V ~50/60 Hz

PreSonus Health, Safety, and Compliance Guide Class B

PreSonus Safety Warnings and Instructions
Electrical information and warning symbols for PreSonus products are located on the rear electrical panel of the unit adjacent to the electrical plug or on the bottom of the unit along with other product compliance information.

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of noninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) AS THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

CAUTION : To reduce the risk of electric shock, do not expose this appliance to rain and moisture. Do not expose this device to dripping or splashing liquids and no object filled with liquids, such as vases, should be placed on the device.

CAUTION: These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operation instructions. Qualified service personnel must perform repairs.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this device near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other device (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the device.
11. Use only attachments/accessories specified by PreSonus.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with this device. Use caution when moving a cart/device combination to avoid injury from tip-over.
13. Unplug this device during lightning storms or when unused for long periods.
14. Servicing is required when the device has been damaged in any way, such as if a power-supply cord or plug is damaged; or liquid is spilled, or objects have fallen into the device; or if the device has been exposed to rain or moisture, does not operate normally, or has been dropped. All PreSonus products in the USA should be serviced at the PreSonus factory in Baton Rouge, Louisiana. If your PreSonus product requires a repair, contact support@presonus.com to arrange for a return authorization number. Customers outside the USA should contact their local distributor. Your distributor’s contact information is available a www.presonus.com.
15. Protective grounding(earthing) terminal. The apparatus should be connected to a  mains socket outlet with a protective grounding(earthing) connection.
16. Where the Mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
17. The use of apparatus is in moderate climates.
18. Please allow 5cm around the apparatus for sufficient ventilation; the ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.

Rackmounting

• Use an equipment rack that is 19-inches wide (482.6 mm) and rated for the total weight of your equipment.
• Use a minimum of (4) 10/32 threaded screws per rack mounted device.

WARNING:
Cancer and reproductive harm – www.p65warnings.ca.gov

PreSonus Compliance Information

European Union (EU)

The CE mark on this product indicates that the device is compliant with the EU Council Directives

• 2014/35/EU Low Voltage Directive
• 2014/30/EU EMC Directive
• 2011/65/EU RoHS Recast
• EC 1907/2006 REACh

For a copy of a specific product DoC, contact PreSonus at support@presonus.com.

RoHS: Recast Directive 2011/65/EU
REACh: Directive EC1907/206

WEEE This symbol on this product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city recycling office or the dealer from whom you purchased the product.

Radio and Television Interference

If these symbols are marked on the product, the device complies as follows:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

USA: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION: Changes or modifications to this device not expressly approved by PreSonus Audio Electronics could void the user’s authority to operate the equipment under FCC rules.

Australian Compliance: This equipment complies with Radio communication Devices Notice 2003; or Radio communication Labeling (Electromagnetic Compatibility) Notice 2008; or Radio communication (Compliance Labeling Electromagnetic Radiation) Labeling Notice 2003.

IC WARNING
IC RSS warning: This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users,the antenna type and its gain should be so chosen that, the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter (identify the device by certifcation number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ICES003: This CAN ICES3 (B)/NMB3(B) digital apparatus complies with Canadian ICES003.

PreSonus Health, Safety, and Compliance Guide. Part# 70-00000013-C
© 2018 PreSonus Audio Electronics, Inc. All Rights Reserved. 18011 Grand Bay Ct. • Baton Rouge, Louisiana 70809 USA • 1-225-216-7887 www.presonus.com

References

• Studio One+
• p65warnings.ca.gov
• PreSonus | Wherever sound takes you.
• p65warnings.ca.gov
• PreSonus | Wherever sound takes you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>