Wicked Audio SYVER True Wireless Earbuds User Manual

Wicked Audio SYVER True Wireless Earbuds

USER MANUAL

IMPORTANT SAFETY INSTRUCTION

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings
4. Follow all instructions.

Attention should be drawn to the environmental aspects of battery disposal;The use of apparatus in moderate climates
This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

SYVER SPEAKER & CHARGING CASE

![SYVER SPEAKER &

CHARGING CASE](https://manuals.plus/wp-content/uploads/2023/08/Wicked-Audio- SYVER-True-Wireless-Earbuds_2.png)

CHARGING the CHARGING CASE and WIRELESS PORTABLE SPEAKER

To charge the Syver Charging Case and Bluetooth Portable Speaker, use the included Micro USB to USB charging cord. Connect the Micro USB (smaller side) into the Charging Case and connect USB side into computer or USB wall charger (not included).

CHARGING THE SYVER EARBUDS

Delicately place the Syver earbuds into the earbud charging nests. Make sure each earbud is placed in its corresponding nest. The cushions on the earbud will face down. A small magnetic pull will help the earbuds fall into the correct position. The Syver earbuds will show a red LED when charging. LEDs will turn off when Syver earbuds are fully charged.

The charging case will shut down automatically if the Syver earbuds both reach full charge or when both of the earbuds are removed from the charging case .

FIRST TIME USE for DUAL EARBUD MODE

(If you want to use a single earbud, please refer to section “Single Earbud Use” on Page 7)

1. Make sure the Syver earbuds are charged (Please refer to section “Charging the Syver Earbuds” on page 2) and Bluetooth device (phone, computer, tablet etc.) is turned on with the Bluetooth feature enabled (this is usually found in settings).
2. Remove charged earbuds from charging case. They will turn on and pair together automatically.
3. Both earbuds will pair together; both will beep and the left earbud will announce “Left” and then the right earbud will announce “Right”, indicating they are now connected to each other.
4. The left earbud will then announce “Pairing” while its LED is flashing Red/Blue. This means your earbuds are now searching for your device to pair with.
5. The right earbud’s LED will be off during the pairing process.
6. Your device will detect the Syver’s pairing name “Wicked Syver BUDS”. Select “Wicked Syver BUDS” on your device to start pairing to your device.
7. Once selected and paired, the left earbud will beep and announce “Pairing Successful”. When paired successfully to your device, both earbuds’ LEDs will be off.
8. You’re ready to go!

FUTURE USE AFTER INITIAL PAIRING THE SYVER TO YOUR DEVICE

(If this is the first time the Syver earbuds are being paired to your Bluetooth device, or if the Syver earbuds were “forgotten”, please see “First Time Use” section on Page 3.)
(If you want to use a single earbud, please refer to section “Single Earbud Use” on Page 7)

1. The earbuds will automatically turn on after being removed from the charging case. If they are already out of the case and turned off, you can turn on the Syver earbuds by holding down the center buttons on both earbuds at the same time.
2. Both earbuds will pair together; . Both earbud LEDs will ash blue while both earbuds “beep” and the left earbud announces “left” and the right earbud announces “Right” and then both earbuds will announce “Second earbud connected.”
3. Your phone will recognize the pairing name “Wicked Syver BUDS” and automatically connect. (If not, please follow the instructions in the “First Time Use” section on page 3. Make sure to check that the Wicked Syver is not already pairing to another device.)
4. Once successfully paired with your phone or device, the left earbud will beep and announce “Pairing Successful”. When paired successfully to your device, both earbuds’ LEDs will be off.
5. You’re ready to go!

TURNING ON EARBUDS

There are two ways to turn on the earbuds:

1. Remove earbuds from their charging case
   OR

2. Hold both center buttons for 3-5 seconds. (This is when the earbuds have shut down outside of the charging case.)
   (For pairing instructions, please see “First Time Use” on page 3.)

TURNING OFF EARBUDS

There are two ways to turn off the earbuds:

1. Place earbuds back into their charging case. They will automatically turn off
   OR

2. Hold center button, on either right or left earbud, for a few seconds until the earbuds beep twice and the LEDs ash red and turn off.
   (Please note when using BOTH earbuds, you only need to hold down ONE center button in order to turn both earbuds off.)

DISCONNECTED

When out of range, or if your device becomes disconnected from the Syver earbuds, the left earbud will beep and announce “Disconnected” followed by “Pairing”. The Syver earbuds will automatically go into pairing mode with the left earbud’s LED flashing Red/Blue while the right earbud’s LED will be off (if you are in dual earbud mode).

PAUSE/PLAY

When both earbuds are paired to your device you can pause and play your music by using a short press on the center button with either the left or right earbud. (Please note when using BOTH earbuds, you can perform this function using EITHER earbud.)

NEXT TRACK

Using the right earbud you are able to skip to the next track by using 2 short presses (double press) on the center button.

ANSWER/HANGUP

When both earbuds are connected, answer or hang up by using a short press on the center button on either the left or right earbud.

INCOMING CALL

When receiving an incoming call, the earbuds will detect the device’s programmed ringtone (this may differ depending on your device)
You can answer by using a short press on the center button on either the left or right earbud.

LOW BATTERY

When using BOTH earbuds together, the left earbud acts as the communicator to your Bluetooth device. Because of this, the left earbud will likely drain its battery quicker than the right.
Please consider charging your Syver earbuds regularly when not in use to retain ample battery life in both earbuds.

If you lose battery life in the left earbud while using both earbuds, the left earbud will announce “Low Charge”. After a couple minutes the earbud will repeat the announcement and then shut off. At this point you can shut off the right earbud and charge both earbuds, or choose to use the right earbud for an additional time in single earbud mode.

The right earbud will take over as the communicator with your device once the left earbud runs out of battery. The LED will ash Red/Blue, indicating it is in pairing mode. Please follow  the instructions in the section “First Time Use- For Single Earbud Use” below.
Please note that when pairing the RIGHT earbud to your device (using single earbud), you will notice that “Wicked Syver BUDS” shows up a second time in your pairing name options. Please pair with the newest “Wicked Syve BUDS ” option as this will be directly connected to the RIGHT earbud.

FIRST TIME USE- FOR SINGLE EARBUD USE

1. Determine if you are using the left or the right earbud.

2. Make sure the Syver earbud is charged and your device is turned on with the Bluetooth feature enabled.

3. Turn on the Syver earbud by removing from the charging case or if it is out of the case and turned off you can turn on the earbud by holding down the center button for a couple seconds. The earbud LED will flash blue “beep”. After a few seconds, once the earbud realizes it will not be pairing with the other earbud, the earbud will announce “Pairing” and the LED will then flash Red/Blue indicating it is in pairing mode.

4. Your phone or device will detect the Syver’s pairing name “Wicked Syver BUDS”. Select “Wicked Syver BUDS” on your device to start pairing them together.

5. Once selected and paired, the earbud will announce
   “Pairing Successful” indicating your device has successfully paired with the Syver. When paired successfully to your device, the earbud’s LED will shut off.

6. You’re ready to go!

Please note when using ONE earbud either earbud can perform all functions. (See previous sections)

FIRST TIME USE WIRELESS PORTABLE SPEAKER

1. Mark sure the Syver Speaker is charged and your device is turned on with the Bluetooth feature enabled.
2. Turn on the Syver Speaker by pressing the Center Power Button (short press). The speaker will beep and announce “Pairing”, while the LEDs flash blue.
3. Your phone or device will detect the Syver’s pairing name “Wicked Syver SPKR”. Select “Wicked Syver SPKR” on your device to start pairing them together.
4. Once selected and paired the Speaker will announce “Pairing Successful” indicating your device has successfully paired with the Syver. When paired successfully to your device, the LEDs on the speaker will be a solid blue.

DISCONNECTED

When out of range, or if your device becomes disconnected from the Syver speaker, the speaker will announce “Disconnected” followed by “Pairing”. The Syver Speaker will automatically go into pairing mode with the LEDs flashing Blue.

PAUSE/PLAY

You can pause and play your music by using a short press on the center

PREVIOUS/NEXT TRACK

You are able to play the previous track or skip to the next track by using a short press on either the -/+ buttons.

VOLUME CONTROL

You are able to control the volume of your music by using a long press on either the -/+ buttons.

TURNING OFF SYVER SPEAKER

To turn off your Syver Speaker simply hold down the center button for a few seconds until you hear the “beep”.

TRUE WIRELESS EARBUD RESET

Troubleshooting

True Wireless Earbuds can sometimes un-sync from one another requiring a manual reset to enable them to auto sync to one another. This “un-syncing” can happen when only one earbud is being used (single earbud mode) or when a Bluetooth device connects to one of the earbuds prior to the two earbuds syncing to each other when they are removed from the charging case powered on.

If sound is only coming out of one earbud, these instructions are for you.

For more troubleshooting and help for your True Wireless buds or our other products please head to our  FAQ and INSTRUCTION BOOKLETS.

It’s simple to reset your earbuds to enable them to auto sync to each other again. Please locate your Wicked Audio True Wireless product below.

Note: Some products have had updates to chipsets, which can sometimes slightly change the resetting procedure. If your product shows a couple different resetting options, follow the first set of instructions, and if those don’t reset your earbuds then try the second set of instructions.

Model #: WI-TW3850

1. Forget all “Wicked Syver Buds” in your device’s Bluetooth settings.
2. Turn off Bluetooth setting on your device.
3. Turn off earbuds out of the charging case. To turn them off outside of the charging case, simply hold down both buttons for 4-5 seconds until the LEDS turn red and shut off
4. Turn on Syver earbuds by holding down both buttons on the earbuds for 8-10 seconds. The LEDs will flash blue followed by flashing Red/Blue. The LEDs will then either turn a purple color and shut off or they will flash Red/Blue and then shut off.
5. Replace the earbuds into the charging case
6. Remove the earbuds from the charging case.  The earbuds will turn on and sync together automatically.
7. Turn Bluetooth back on on your device
8. Find/Select “Wicked Syver Buds” on your device

PRECAUTIONS

LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE.

Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound pressure levels before hearing damage occurs.

SAFE USE & HAZARD WARNINGS

90 dB SPL at 8 hours| 95 dB SPL at 4 hours| 100 dB SPL at 2 hours| 105 dB SPL at 1 hours
---|---|---|---
110 dB SPL at 30 min| 115 dB SPL at 15 min| 120 dB SPL: Avoid as damage may occur

LIMITED ONE-YEAR WARRANTY

Keep your receipt to obtain warranty service. Go to
www.wickedaudio.com for more details.

Developed in Utah, U.S.A.
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>