SONOFF BASIC-RC Wifi Smart Switch User Guide
- June 13, 2024
- SonOFF
Table of Contents
BASIC/RF
Quick Guide v 1.4
Wi-Fi Smart Switch
Power off
To avoid electric shocks. please consult the dealer or a qualified professional for help when installing and repairing Please do not touch the switch during use.
Wiring instruction
Ceiling lamp wiring instruction
Light fixture wiring instruction
**** Make
sure all wires are connected correctly.
Download the eWeLink App
Power on
After
powering on, the device will enter the Pairing Mode during the first use. The
Wi-Fi LED indicator changes in a cycle of two short and one long flash and
release.
**** The device will exit the Pairing Mode if not paired within 3mins. If you want to enter this mode, please long press button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
Add device
Tap “+” and select “Add Device”, then operate following the prompt on the App.
User Manual
https://sonoff.tech/usermanuals
Scan the QR code or visit the website to learn about the detailed user manual and help.
FCC compliance statement
1.This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. 2.Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
Interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm between the
radiator and your body. This transmitter must not be co-located or operating
In conjunction with any other antenna or transmitter.
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference. (2)This device must accept any interference,
including interference that may cause undesired operation of the device. This
Class B digital apparatus complies with Canadian ICES-003(B). This device
complies with RSS-247 of Industry Canada. Operation is subject to the
condition that this device does not cause harmful interference.
ISED Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
| Scatola | Manuale |
|---|---|
| PAP 21 | PAP 22 |
| Carta | Carta |
RACCO LTA
SAR Warning
Under normal use of condition, this equipment should be kept a separation
distance of at least 20 cm between the antenna and the body of the user.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type BASICR2/RFR2 is in compliance with Directive 2014/53/EU.The
full text of the EU declaration of conformity is available at the following
Internet address: https://www.sonoff.tech/usermanuals
For CE Frequency:
Operation frequency Range:
Wi-Fi:2412-2472MHz
SRD: 433.92MHz (RFR2, Receive Only)
RF Output Power:
14.43dBm(802.11b), 11.94dBm(802.11g),
11.96dBm(802.11n20)(Wi-Fi)
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012 /19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the
recycling of waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about
the location as well as terms and conditions of such collection points.
Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000 Website: sonoff.tech Service email:
support@itead.cc
MADE IN CHINA
To
ensure the safety of your electrical installation, it’s essential either a
Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker
(RCBO) with an electrical rating of 10A has been installed before the device.