KFI PRODUCTS UTV-DRS UTV Dash Rocker Switch Instruction Manual
- June 13, 2024
- KFi PRODUCTS
Table of Contents
UTV DASH MOUNTED
ROCKER SWITCH
Instruction Manual
MODEL NUMBER
UTV-DRS
UTV-DRS UTV Dash Rocker Switch
SAVE THESE INSTRUCTIONS
Important Safety Instructions are included in this manual.
721 Sata Drive
Spring Valley, MN 55975
USA /1-877-346-2050
www.kfiproducts.com
CONTROlS AND FEATURES
UTV Dash Rocker Switch
- Rocker Switch – Used to power the rope in or out of your winch drum. This switch is a Double Pole/Double Throw (two contact points per IN or OUT)
WIRING LAYOUT
Switch Wiring Diagram
**Terminal
2, #5, #8 and #10** – Power to Switch (+) (Connect to RED wire on contactor)
– #8 and #10 are for ignition power to LED’s
Terminal #1 and #4 – Signal for Winch -IN- (Connect to small GREEN wire
on contactor)
Terminal #3 and #6 – Signal for Winch -OUT- (Connect to small BLACK wire
on contactor)
Terminal #7 and #9 – Ground (-) for LED (Connect to Frame ground or
Battery (-) NEGATIVE post on the contactor)
INSTAllATION
Note: Before installing make sure you have the correct orientation for the switch with the tab facing towards you.
- Insert the blue diodes (A) first and small spring (B) second into the designated hole on each side shown in Figure 1.
- Insert the two large springs (C) into the designated holes on each side shown in Figure 1.
- Set the clips (D) Face up into the designated location shown in Figure 1.
- Set the white rocker plunger onto the post in the top portion of the switch shown in Figure 2.
- Take the top portion of the switch and set it on the bottom portion. Shown in Figure 3.
- Note: The “In” position is lined up with the (Tab) on the one side of the switch so you know how to attach it back together correctly. Shown in Figure 3.
- There is a clip on each side of the rocker switch. Push the top portion of the switch down and snap the clips into place. Shown in Figure 3.
WARRANTY
WARRANTY
KFI Products
1 YEAR LIMITED WARRANTY
Warranty Qualifications
Kappers Fabricating, Inc. (KFI) will warranty with a copy of your sales
receipt from one of KFI’s retail locations as proof of purchase.
Repair/Replacement
Warranty
Kappers Fabricating, Inc. (KFI) warrants to the original purchaser that the
mechanical and electrical components will be free from defects in materials
and workmanship for a period of one (1) year from the original date of
purchase. We will repair or replace, at our discretion, parts found to be
defective due to materials or workmanship.
This warranty applies only to products which have been properly assembled,
adjusted, and operated in accordance with the instructions contained within
the product manual. This warranty does not apply to any product of Kappers
Fabricating, Inc. that has been subject to alteration, misuse, abuse, improper
assembly or installation, or shipping damage.
Do Not Return The Unit
To The Place Of Purchase
In the event you have a claim under this warranty, contact KFI’s Technical
Service and KFI will troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, KFI will, at its option, authorize
evaluation, repair or replacement of the defective part or component at a KFI
Service Center. KFI will provide you with a case number for warranty service.
Please keep it for future reference. Repairs or replacements without prior
authorization, or at an unauthorized repair facility, will not be covered by
this warranty.
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
This product needs periodic parts and service to perform well. This warranty
does not cover repair when normal use has exhausted the life of a part or the
equipment as a whole.
Other Exclusions
This warranty excludes: Cosmetic defects such as paint, decals, etc. Failures
due to acts of God and other force majeure events beyond the manufacturer’s
control. Problems cause by parts that are not original KFI Products parts.
Failures due to Water intrusion.
limits of Implied Warranty and Consequential Damage
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND
ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR
ALL EXPRESSED WARRANTIES.
THE WARRANTY SET FORTH ABOVE IS THE ONLY WARRANTY. THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow the exclusion of implied warranties or the exclusion
or limitation of liability for incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights.
You may also have other rights that vary from state to state.
Contact Information Address
KFI Products
Customer Service
721 Sata Drive
Spring Valley, MN 55975
www.kfiproducts.com
Technical Service
Mon – Thu, 8:00 AM – 5:00 PM (CST)
Fri, 8:00 AM – 1:00 PM (CST)
Toll Free: 1-877-346-2050
tech@kfiproducts.com
1) Install Switch to desired location on your dash
- Most UTV’s and SxS’s have predefined switch locations that are pre-scribed or marked for mounting and require finish cut with a knife.
- Use the cut-out dimensions shown below to cut-out the switch location If your dash doesn’t have the pre-scribed areas.
- Pull the plug end of the wiring harness through the hole and connect it to the rocker switch outside the hole before inserting the switch.
Note: Insert the switch carefully, if the hole is to small trim some of
the plastic.
This switch comes in two pieces for ease of installation, is not designed to
come back apart after installing.
1-877-346-2050
KFI Products
P.O. Box 32
721 Sata Drive
Spring Valley, MN 55975 USA
www.kfiproducts.com
Made In China
©2016 Kappers Fabricating, Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>