TRIBIT BTH78 QuietPlus 78 Headphones User Manual
- June 13, 2024
- Tribit
Table of Contents
TRIBIT BTH78 QuietPlus 78 Headphones User Manual
Package Contents
Product Diagram
- Volume + / Next Track
- MFB Button
- Volume – / Previous Track
- LED Indicator
- ANC/Ambient Button
- 3.5mm Audio Input
- USB Charging Port
- Microphone
Turn on / off
- To power on the headphones, press and hold the MFB button for 2 seconds. The LED indicator will flash white for 2 seconds.
- To power off, press and hold the MFB button for 5 seconds. The LED indicator will flash red for 2 seconds and then go off.
Bluetooth Connection
- Press and hold the MFB button for 5 seconds until the LED indicator flashes white. A moment later, the headphones will automatically enter pairing mode, with the LED flashing red and white alternately.
- Activate the Bluetooth function on your Bluetooth-enabled device. Select the Tribit Quiet Plus 78 from the list of Bluetooth devices found by your device and connect.
Simultaneous Connection with Two Devices
- Follow the instructions in the “Pairing” section to pair the headphones with Device A.
- Once paired, disable the Bluetooth function on Device A.
- Follow the instructions in the “Pairing” section to pair the headphones with Device B.
- Once paired with Device B, reactivate Bluetooth function on Device A and select “Tribit QuietPlus 78” in the list of paired devices.
- You can now make and receive calls from either of the two paired devices.
Noise Cancellation
The Noise Cancellation Function can reduce the unwanted noise to provide you with a clearer, more lifelike audio effect. You can choose your noise cancelling mode based on your listening preference and environment. Noise Cancellation Function under ANC mode (with headphones on): When the headphone is on, press the ANC button once to enter the ANC LOW mode; press the ANC button again to enter the ANC HIGH mode; press the ANC button the third time to enter the pass through mode; press the ANC button the fourth time to turn off the ANC —the button function cycles in this way.
Noise Cancellation Function under ANC mode (with headphones off ): Press and hold the ANC button for 2s to enter the ANC LOW mode; press the ANC button again to enter the ANC HIGH mode; press the ANC button the third time to enter the pass through mode; press the ANC button the fourth time to turn off the ANC —the button function cycles in this way.
Operation of Buttons
Voice Prompt
Charging the Headphones
Connect the USB cable to the USB port on the headphone, and a 5V power outlet (power adapter is not included). The indicator light will glow red to indicate charging. When the headphones are fully charged (within 3 hours), the indicator light will change from red to white.
Customer Service
The headphones have a full 18-month warranty against manufacturing defects starting from the purchase date. For FAQs and more information, please email to support@tribitaudio.com.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>